Question about 2006 Hyundai Sonata

2 Answers

My high level brake light has bruned out,(third brake light). I was informed by the dealer the back window panel has to be removed to replace the 3.00 dollar bulb, total cost 75.00 dollars. With some

The third high level brake light has burned out on my 2006 Hyundai Sontata

Posted by on

  • ernie2889 May 26, 2009

    When removing the "C" pillar covers does this mean you have to remove the curtain airbags too.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Replace the bulb...??? This requires you remove the rear package deck (to access the bulb & socket). to do this, remove the seat bottom (two bolts hold the rear seat bottom to the chassis, then remove the bolts which hold the shoulder cushions (LH & RH - 12mm bolts) then remove the cosmetic molding around the trunk access (7 to 8 screws) then remove the "C" pillar covers (SRS curtain airbag LH & RH) to access the rear deck package & access the third brake lamp bulb. replace it, then reassemble.

Posted on May 26, 2009

  • Paul McGrath
    Paul McGrath May 26, 2009

    replace the bulb...??? This requires you remove the rear package deck (to access the bulb & socket). to do this, remove the seat bottom (two bolts hold the rear seat bottom to the chassis, then remove the bolts which hold the shoulder cushions (LH & RH - 12mm bolts) then remove the cosmetic molding around the trunk access (7 to 8 screws) then remove the "C" pillar covers (SRS curtain airbag LH & RH) to access the rear deck package & access the third brake lamp bulb. replace it, then reassemble.

  • Paul McGrath
    Paul McGrath May 27, 2009

    No... do not remove the curtain airbag initiators... only the C pillar covers (they need to be moved out of the way so you can remove the rear deck package and access the 3rd brake light fixture/assy.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

**** this car

Posted on Jun 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Odd problem oil light illuminates when I hit brake real hard 2006 hyundai elantra


Low oil level in crankcase? Check that out since hard braking will cause the fluid to move to one end and perhaps give a low false reading.

Sep 17, 2016 | 2006 Hyundai Elantra

2 Answers

How do I replace the high mount brake light on my 2011 Chevy Malibu?


You need to take the back seat out. Remove the C-Pillar trim panels. Lift up on the package shelf. Unplug the wiring connector. I've had mine out when I changed the speakers.

BTW, Its Not a Bulb. Its a LED Assembly. Replaced as a whole unit. Unless your good with electronics and soldering.

Jul 16, 2015 | 2011 Chevrolet Malibu

2 Answers

HOW TO REPLACE HIGH MOUNT BRAKE LIGHT 2002 CADILLAC DEVILLE


The light will be fitted from inside the trunk. You might need to remove any trim or lining on the trunk lid. There will be 5 small nuts on the inside of the trunk lid. 2 each end and one centre. The light should drop out. It could be tight so GENTLY rock it up and down to free it.
** NOTE ** The light fitting is likely to be a sealed unit so you will have to replace the whole light as you cant get access to the bulbs.

Mar 01, 2018 | Cars & Trucks

1 Answer

3rd light diagram


Found these online for you... hope they help.
This first link is specific to your 1st Generation Ody....it's a great forum and hope you get your answers there
http://www.odyclub.com/forums/28-1995-1998-odyssey/20360-need-help-96-third-brakelight.html



http://www.odyclub.com/forums/52-2005-2010-odyssey/57976-how-replace-high-mounted-rear-brake-light.html
In my 2002 Honda Odyssey, the high brake light is accessed by removing a small triangular red piece from the right side of the cover. This piece often breaks but I was successful by soaking the area with STP silicone spray, waiting 15 minutes and then prying the piece up in the slot on the left side with a miniature flat bladed screwdriver. You then remove the underlying screw amd remove the housing. Twist the bulb holder out and remove the bulb by pulling straight out. Push the new bulb in - I usually hold it in a paper towel because by this time my hands are dirty. Twist the bulb holder back in. Push the housing back in starting on the left side. Replace the screw. Put in the triangular piece starting with the right side clip. I then pry the housing open with my screwdriver very carefully to fit the left clip in. If you break the piece it's under $10 at the Honda dealer. The piece is not well designed but you can make it work if you're patient.

Also, be sure you purchase the replacement light bulb lamp first before you tear everything apart. See sources and related links below for more light bulb information.

Read more: http://wiki.answers.com/Q/How_do_you_replace_high_rear_brake_light_on_a_Honda_odyssey#ixzz1nFpCWpiu

Feb 23, 2012 | 1996 Honda Odyssey

1 Answer

None of the brake lights on my daughters 2010 Hyundai Accent, come on when she steps on the brake pedal. why?


You listed this vehicle as a 2006 Accent, yet you write it's a 2010.

If 2006, it's probably the brake lamp switch. However, I've seen all three brake light bulbs burn out within days of each other.

If 2010, it's still under warranty.

Aug 29, 2011 | 2006 Hyundai Accent

1 Answer

After having my 2006 santa fe serviced at 60000 miles, my cruise control doesn't work. I had it lubed, radiator flush, oil change, brakes checked, timing belt replaced, water pump replaced.


Try checking all of your rear brake lights to see if they are working.If you have a burned out bulb the control cannot complete the circuit and the cruise will not work. Dont forget the third brake light sometimes have more than one bulb in them so check closely to make sure that all bulbs are good.

Jun 11, 2011 | 2006 Hyundai Santa Fe

1 Answer

How to replace the third brake light (hatch) on a 2005 hyundai accent. I took off the 4 screw on the the plastic cover and it still won't come off. Tried taking off cove of back hatch but don't want to...


Above the third brake light is a small panel, remove this panel using small screwdriver.
1. You'll see four (4) bolts, remove the three bolts that are painted black, do not remove the center bolt holding the plastic molding, this is for the door molding, and has nothing to do with the light.
2. Once those three bolts are out, you'll see two more small screws, remove them and you'll have access to the third brake light bulb.

Be careful when pulling out the bulb, my bulb broke, and I'm still trying to get pieces out! - Good luck.

Jan 16, 2011 | 2005 Hyundai Accent

2 Answers

Where is the bank 1 sensor 1 o2 sensor located in a 2006 hyundai sontata gls v6?


The bank has to do with which side of the engine. The 'Sensor 1' indicates that it is upstream of the catalytic converter.

Heated Oxygen Sensor Removal & Installation Heated Oxygen Sensor (Front) (2.4L) hyundai-04-24-5822.gif

Heated Oxygen Sensor (Rear) (2.4L) hyundai-04-24-5823.gif

Heated Oxygen Sensor (Bank 1/Sensor 1) (3.3L) kia-04-00-5213.gif

Heated Oxygen Sensor (Bank 1/Sensor 2) (3.3L) kia-04-00-5214.gif

Heated Oxygen Sensor (Bank 2/Sensor 1) (3.3L) kia-04-00-5215.gif

Heated Oxygen Sensor (Bank 2/Sensor 2) (3.3L) hyundai-04-33-5855.gif

prev.gif next.gif

Jan 13, 2011 | 2006 Hyundai Sonata

2 Answers

Wondering how to change the third brake light (one located in back window) on a 2006 hyundai sonata


High Mounted Stop Lamp Removal & Installation To Remove:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Disconnect battery negative cable.
  2. Disconnect high mounted stop lamp electrical connector from inside trunk.
  3. Remove package tray.
  4. Replace bulb from package tray.
To Install:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Install package tray.
  2. Connect high mounted stop lamp electrical connector from inside trunk.
  3. Connect battery negative cable.
prev.gif next.gif

Oct 12, 2010 | 2006 Hyundai Sonata

2 Answers

Rear brake lights, rear turn signals inoperable. bulbs replaced and are working, simply not responding to brake or turn signal?


If the third brake light always works, then it is the turn signal switch. If the third brake light does not work, it is probably something else. The turn signal switch is in the steering column. You have to remove the airbag and steering wheel, take out all of the componets and replace the turn signal switch. Special tools are required and a moderate level of mechanical ability. Watch the airbag, it can go off and cause serious injury!!

Sep 24, 2010 | 2004 Chevrolet Malibu

Not finding what you are looking for?
2006 Hyundai Sonata Logo

1,330 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...