Question about 2002 Dodge Intrepid

1 Answer

Door handle and window

The hole that holds the door mechanism broke cam i replace that one piece or do i have to replace the inside of the hole door also the window goes up slow and keeps going off the track what can i do.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 129 Answers

What you'll need to do is replace the door regulator with a good used one or a new one. The fact that it's broken probably is the cause of the glass going off track. Call your local Recycle Yard or NAPA for a replacement part.

Posted on May 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replacing door handle on a 2007 Chevy Equinox and wife had turned on child safety lock. Door shut and can not open? How can I open when there is no door handle on it and child safety lock on?


Are you saying the door handle is broken off? Then you must remove the door panel from the inside with the door closed, it is difficult but can be done by most deals with seasoned techs that have done it before.

Sep 12, 2012 | 2007 Chevrolet Equinox LS New Cars

1 Answer

The front passenger door will not open with the outside door handle or the interior door handle. after taking the inside door cover off, i discovered the interior door handle is broken and the connector...


The locking mechanism is manufactured with carbon composite and plastic levers that the door handles attach to. It is hard to tell what parts that you do need. Remove the passenger side door panel. It will have some screws and maybe a bolt on the inside handle. The panel has snap plug on it and they fit into designated hole in the door. After getting the door panel off, be careful here, there are sharp metal edges that can cut. There are some peep hole to see the rods and connector inside the door. If the plastic hooks on the door locking mechanism are broken. The hole door lock assembly will need to be replaced.

Try your local wrecking yards and tell them what type of vehicle you have and year. Also, state what door it is and what you will need.

Now, if the interior door hand hook on the lock mechanism isn't broke off. The get a cloths hanger and straighten it out and attach it to the opening latch on locking mechanism. This will give you inside temporary handle, while you are trying to fix the door. Safety. GB...stewbison

Sep 06, 2011 | Nissan Sentra Cars & Trucks

1 Answer

How do I fix the door/lock of my 1991 Acura Integra? I can only open the driver side door from the outside


There are only 2 places that you have the problem on the inside door handle. one is at the handle,and the little plastic holder that holds the rod to the handle broke, or the plastic clip the the door lock mechanism broke. the first can be removed without taking the door apart. the inside door handle has a screw holding it in place. you can remove the handle and see if its broken. the second requires you to remove the door panel, to replace the clip that hold the rod to the lock. I door handle in the car is a dealer item only(sorry to tell you that), the clip for the lock, you can get at the auto parts store. hope this helps

Jan 11, 2011 | 1991 Acura Integra Hatchback

1 Answer

The front door handle lacks tension and the door won't open from the outside. However, the door will open from the inside.


I just bought a 96 transport with that same problem on both front doors they would open from the inside but not the outside. They have a design flaw, basically when you pull the handle it pushes a piece that pivots and in turn pushes a linkage rod downward that actuates the door latch, well that pivot point is the weak spot, the pin that it hinges on is too small and will break, (I found the pivot piece and the linkage rod laying in the bottom of the door)
If you pull the door panel off their are 2 nuts holding the door handle on, take those off and the door handle will come off, the pivot pin is on then inside of the door handle, what I did was to drill a hole and put a small self tapping screw in to replace the pivot pin, and hold the pivot piece and linkage in place then put it all back through the door handle hole in the door, and set the linkage down in it's hole in the door latch assembly. The screw I used was not exactly the same size as the original pin was so the pivot piece had some play in it and did not quite push the down far enough to unlatch the door so I put two small nuts to act as washers on the bottom of the linkage rod so it would push down a little more, now it works like a charm, on the other door the linkage rod had just come out of it's hole in the door latch assembly, all I had to do was pull the inside door handle, which lowered the door latch piece and guided the rod back into its hole as I released the inside door handle and now it works too, took about an hour for both doors, a fairly easy fix, hope this helps.

Dec 15, 2010 | 1996 Pontiac Trans Sport

1 Answer

Driver's inside door handle broke. How do I get


found this while looking to replace speakers:

DOOR WITH POWER LOCKS AND WINDOWS First remove the triangle piece in the top corner of the panel (piece closest to the outside mirror). This can be done with a plain screwdriver and just a little
prying and it will snap off. Second, remove the door lock inset, same screwdriver, little prying and it snaps out. Next remove the cover inside the door handle, same screwdriver, pry and snaps out
(turn it upside down and slide it off. Now you will need to remove the cover that holds the window
and door lock buttons, same screwdriver and pry upwards just a little and should pop off. Ok now you
will need a small socket to take out three screws. One is inside the button panel you just took off,
the second is inside corner of the door arm, (the handle you grab to shut the door, look under it,,
see it yet, yeah thats it). The last screw in on the very bottom of the whole door panel, you will
have to get on your hands and knees to see this one (yeah thats it right there). Now would be a good
time to remove the door light on the corner, same screwdriver, pry from the red lens side outward,
once out, remove the wire termial. Ok.... now grab the under side of the panel where that last screw
was and lift upwards, apply a little more pressure till the panel pops upward about an inch. Now your
door panel is loose, you can lift it off a little but you will need to remove the wire from the tweeter.
The termial has a locking tab you need to press down to remove it.

Apr 30, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

How to replace a door handle on a 2006 hyundai sonata, i either broke the handle and need to replace it or I am trying to figure out how to fix the drivers side handle


Step1: First, unscrew the 7 screws holding on the door panel
Step2: Next you carefully pry off the tweeter cover that is where the mirror is.Lift the panel up and off of the door . Undo all of the wiring connections except for the window controller.
Step3: Open the 2 black rubber view ports (Circled in Yellow) and roll the window up or down until you see the 10mm bolts that hold the window in place.
Step4: Loosen, but don’t remove these bolts. Slide the window up, and tape it up, or remove the window and set aside. Next, unplug the door lock plug and move the door panel out of the way.Unscrew the gold 10mm bolts that hold on the metal inner door panel . Also remove the Phillips screw that holds the inner door handle on
Step5: Unscrew the small bolt that holds on the lock cylinder that is behind the quarter-sized black cap on the side of the door. Be careful with that little bolt or it will fall into never land .Pull the lock cylinder out and set aside.
Step6: Now grasp the door handle, and with your free hand smack your hand holding the handle towards the back of the car. This will release the door handle.Under the door handle is a Phillips screw. Loosen this screw a few turns but don’t remove.
Step7: Now undo the 3 black star shaped screws on the door lock.You can now wiggle the inside of the door handle until it comes free. See the tabs that hold it onto the door . When you go to put it back on be sure the tabs get back in the right place.Pull the whole inner door panel and lock mechanism free by wiggling it out of where it sits.
Step8: Now you can undo the 3 cables; 1 from the outer door handle yellow mechanism, 1 from the inner door handle mechanism, and 1 from the inner door lock lever.Put on the new lock and put it all back together. Be sure to test it as you go. I had to turn the lock cable to the inner door lock lever 180 degrees because it was not unlocking properly when I put it back together the first time.
A couple of other notes, there are 2 pieces of plastic that are for the robots to use when putting the door together for the first time. one is a 3 pronged white plastic thing riveted to the inside of the metal door panel. The other is a white plastic thing covering the lock mechanism. You can cut off the fingers and throw the plastic cover away they are both useless and in the way.When you put it all back together, just go in the opposite order of disassembly. It is a little tricky to get the yellow plastic outer door handle holder into place. Be sure that the little tabs grab the metal of the door or things will not fit together properly.Be sure to test the power window after you put the window back in place. Do not overtighten the bolts on the window, it is glass…..

Apr 08, 2010 | 2006 Hyundai Sonata

1 Answer

2005 volvo s60 inside door latch broke


That is not true.
The handle fell off on the inside. You can remove all the screws, remove window and lock controls. Then take a large flat-tipped screwdriver gently pry off door panel. Pull up and off when loose. You will now have access to inside off door and put the rod back in the handle hole. If the plastic holder piece is broke you will need another one. Cheap.


Oct 01, 2009 | 2002 Volvo V70

1 Answer

2003 Ford Explorer back door latch will not open


Mine just did the exact same thing. The latch may be moving freely because it is not hooked to the latching mechanism anymore. In my case, the handle had broken where the handle hooks to the rod that operates the mechanism. Go to the Ford dealer and buy a new handle. Here in S.C. it was $24. You can't get this at the parts houses. Start by removing the plastic "Ford" cover that is over the liscense plate lights. You then have to remove the aluminum rivets that hold the handle to the tailgate from the outside and remove the broken latch. Remove the pull handle loop on the interior side of the tailgate (2 screws), unsnap the inside plastic tailgate interior panel, and pull down the black plastic sheeting that is underneath the panel to make access to the mechanism inside of the tailgate. There is also a hard plastic cover that you will see that needs to be pulled loose to open another access hole. Install the new tailgate latch handle by sliding back into the mounting holes and attach with two 10-32 screws and nuts. The new handle will come with a new yellow rod attachment piece on the handle. You will see inside of the tailgate a small rod hanging down, most likeky it will have the same rod attachment piece as the one on the new handle. Note the position of the yellow piece on the rod, as you will connect the new piece in the same place. Once the rod is hooked up, relubricate the metal mechanism with a light machine oil, replace the black plastic cover, replace the black plastic sheeting, (secure with a small amount of duct tape), replace the tailgate interior panel, replace the pull handle loop, shut tailgate, replace "Ford" cover over lights, and you're done!

Mar 23, 2009 | 2003 Ford Explorer Sport

2 Answers

Hyundai accent '02 inside door handle & Lock removal


Removing the door is very tricky, trust me on this. I ended up breaking it the first time, so please learn from my mistake.

1. Remove all visible screws: 2 at bottom of door, 3 on front near hinge, 1 on inside the door lever. You will need an average size phillips screwdriver to do this.

2. On the door handle itself, you will see two circles. Pop the front one out. You will need a LARGE size phillips screwdriver to do this.

3. Once screws are removed, take a (standard) flat-head screwdriver, preferable one with a large face, and pry the triangular piece of plastic (that covers the outside SIDE mirror) off. This will aide in puting the door panel back on...TRUST ME!!!

4. Take the same flat-head screwdriver, and pry behind the door lock (at the same time, push forward toward the door hinge). The assembly should pop out.

5. Gently pry the door panel from the door, making sure not to break any unnecessary pieces along the way. The door panel should be hanging by the window sill opening.

6. This is where it will get tricky. It is advised that you use help with this part: Angle the door panel at a 45 degree angle. AT THE SAME TIME, slightly bend and twist the door lock handle until it fits through the hole. You will see the 3 pegs the held it in the door from before. Also note: Be careful not to break the 2 poles that are attached to the lock.

7. After popping the lock through the hole, you should be able to lift the door upward, and off the sill. Repeat these steps in reverse order to re-attach door panel.

Be careful not to rip sound-deadening paper found on inside of door unless you intend to remove or replace it! Not only does it prevent dirt and moisture from entering your door (and possible rusting it from the inside out), but it makes your speakers sound better too!

-SportTunerFreak

**It is also recommended to put a tiny bead of silicone on the inside of the door panel to help suppress any rattling, and prevent moisture and dust from entering. It also helps your screws obtain a tighter fit. Hope this helps!

Mar 07, 2009 | 2002 Hyundai Accent

2 Answers

Removing the door panel to a 1996 Audi A6 Quattro


This info is wrong, remove the screws at the top of the panel along the edge ( one on the hinge edge and one on the latch edge. Remove the cover from the interior door handle by locating the hole on the bottom edge of the handle, insert a punch to release the cover, once the cover is released remove the 2 screws holding the handle on. Remove the handle.Once the handle is removed take the black trim piece that the handle seats into off. Pull the interior latch handle forward enough the remove the cable. Remove the latch handle. There is a small hole in the vynal under the latch handle, the last remaining screw that holds the panel on is inside this hole, remove it. The hole is hard to see, this took me several hours to find not knowing it was there. Remove the window switch module by sliding a screwdriver under the edge that faces the latch end of the door, push in the metal clip and pry up on the switch assembly. there are 2 plastic tabs that hook into the arm rest on the hinge end, that is why you must pry up from the latch end. Disconnect the plugs from the switch. Now you are ready to remove the panel. grasp the panel through the hole for the latch handle and pull up about 1" the panel should com free from the door. Do not pry the panel out from the door or you will break the plastic tabs that hold the panel on. Once you lift the panel up and off the door you will need to disconnect 2 electrical connectors and remove the white foam plug that seals the window switch harness into the arm rest and remove the window control wires from the panel.

Dec 13, 2008 | 2002 Audi A6

Not finding what you are looking for?
2002 Dodge Intrepid Logo

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...