Question about 1997 Lincoln Continental

2 Answers

SERVICE ENGIN SOON LIGHT

HOW DO I TURN OFF SERVICE ENGIN SOON MESSAGE WHEN THE PROBLEM IS FIXED (REPLACE UPPER AND LOWER MANIFOLD GASKETS)

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 410 Answers

You need an OBD II code reader.  Hook it up to your car like you would when you read the code initially and then erase the code.  If you don't have a code reader then you can go to your local auto parts store and they should be able to erase the codes for you.  Thanks for rating my response and for using FixYa!

Posted on May 25, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Try this take the positive side off the battery for about 3- secs and put back on if all the problems are fix with the car it should stay off

Posted on May 25, 2009

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ftw1952
  • 10319 Answers

SOURCE: SERVICE ENGIN SOON MESSAGE

disconnect the negative ground to your battery for 5 minutes than re attach it. Once you drive the car for 50 to 100 miles the computer will be reset

Posted on May 25, 2009

  • 316 Answers

SOURCE: TURN OFF SERVICE ENGIN SOON

You have to have the codes reset. Take your vehicle to your local autozone, they will do it for free.

Posted on May 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REPLACE UPPER AND LOWER GASKET


This is going to be a pain, due to the age and rust. I assume when you say upper exhaust gasket. You are referring to the manifold to head gasket. If so you need to soak the stud/nuts with PB Blaster lube then back out the nuts, to remove the manifold. For the lower gaskets I assume you are referring to the donut gaskets where the pipes meet, I am pretty sure this model does not use donut gaskets.

Feb 14, 2014 | 2000 Ford Taurus

2 Answers

How do i fix emission codes p1131 p1151 p0171


TSB
05-22-6
ISSUE:
Some 2001-2003 F-150, 2004 F-150 Heritage and 2001-2003 E-150/250 vehicles equipped with a 4.2L engine may exhibit the malfunction indicator lamp (MIL) on with diagnostic trouble codes (DTCs) P1131 and/or P1151 (system too lean bank 1 or 2). This condition may be due to leaking isolator bolts/port gaskets in the upper-to-lower intake manifold mounting area. This condition is sometimes intermittent and may not be apparent on a warmed-up engine.


SERVICE PROCEDURE

Perform a self test. If DTC P1131 and/or P1151 are the only codes stored in the powertrain control module (PCM) proceed to Step 2. If any additional DTCs are present, follow normal diagnostic procedures found in the PC/ED Manual.

Remove the upper intake and replace only the port gaskets (9H486) and isolator bolt assemblies (9S479). The new isolator bolt assemblies use a rubber material that is green in color, do not install the old isolator bolt assemblies with the black rubber material. Do not replace any other intake parts or gaskets.
While the upper intake manifold is removed, check the exhaust gas recirculation (EGR) orifices that are pressed into each primary port of the lower intake manifold. If any of the orifices are plugged with soot, clean and unplug them with a pick and solvent.

PART NUMBER PART NAME
1L3Z-9H486-AA Port Gasket
3F2Z-9S479-AA Isolator Bolt

Jan 13, 2010 | 2003 Ford F150 Regular Cab

1 Answer

Blown upper air intake manifold on gm 3800 series two engine


Parts stores carry a kit including a manifold and gaskets. When I do the job I always replace the lower intake gaskets because they leak too. Make sure the lower manifold is not warped around the rubber gaskets towards the throttle body side, a new or used loewr manifold might be needed to ensure a correct repair.

Sep 22, 2009 | 1998 Buick LeSabre

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

1 Answer

TURN OFF SERVICE ENGIN SOON


You have to have the codes reset. Take your vehicle to your local autozone, they will do it for free.

May 25, 2009 | 1997 Lincoln Continental

1 Answer

WAS TOLD THAT THERE IS A P[RODUCT THAT CA BE PURCHASED FOR A VERO


disconnect the battery to clear the KAM and all fault codes. 1/2 hour. Then reconnect and drive for 10 miles. It may run rough until it relearns engine controls. please rate as solved if this fixes issue

May 25, 2009 | 1997 Lincoln Continental

1 Answer

SERVICE ENGIN SOON MESSAGE


disconnect the negative ground to your battery for 5 minutes than re attach it. Once you drive the car for 50 to 100 miles the computer will be reset

May 25, 2009 | 1997 Lincoln Continental

1 Answer

TURN OFF SERVICE ENGIN SOON MESSAGE


take it into a dealership they will have a tool to take it off

May 25, 2009 | 1997 Lincoln Continental

3 Answers

CODES P0171 & P0174 EMISSION SYSTEM SERVICE


if you have the 3.8 liter its more than likely bad intake manifold gaskets or a cracked manifold. Ford has had several TSBs on this issue. O2 sensors do not go bad as often as mechanics say they do. I have a 1999 that after 100 dollars at the parts store solved all lean conditions on the top end. The manifold has three parts to it. A lower aluminum that houses the butterfly blades for the variable intake runners( known vacuum leak were rods protrude at passenger side of lower bad bushings likely cause). Middle riser which uses oring seals which dry out and cause major vacuum leaks. upper is more or less the top cover which uses one large oring to seal. Hope this helps!

Feb 06, 2009 | 2000 Ford Windstar

1 Answer

Manifold gaskets


If you are talking about 3.4L engine there are only two manifold gaskets. But there are Four Intake gaskets two for the upper intake and two for the lower intake.

Oct 08, 2008 | 2001 Pontiac Grand Am SE

Not finding what you are looking for?
1997 Lincoln Continental Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...