Question about 1992 Ford F250

2 Answers

TRANNY WONT WORK

YESTERDAY I WAS DRIVING MY TRANNY STARTED SLIPPING, THEN SMOKING WHEN I PULLED OVER ALL THE FLUID BOILED OUT AT THE BELLHOUSING, WHERE IT MEETS THE ENGINE ANY IDEAS?? WES

Posted by on

  • littlefordjr May 25, 2009

    thanks, i was hoping it was something not so seriuos.. thanks again

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,623 Answers

Hello....Sounds like the front converter seal has failed...common on these transmissions. The fluid overheats and blows the seal, moreso if any towing is done.
To prevent this...install a trans. temp gauge and a good aftermarket fluid cooler.
Good luck...hope this answers your question.

Posted on May 25, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

Yes you blew the front pump seal you prob need too replace or rebuild the tranny!!!!!!1

Posted on May 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I ran through water transmission was submerged now when you start it will go in every gear and pull no slipping then it wont pull in any gear I clean the filter and replace the transmission fluid


If water got into the tranny itself there is close to no way to remove it.
A tranny flush only removes a small portion of fluid in the tranny.

Mar 06, 2016 | Cars & Trucks

1 Answer

My 2003 chevy blazer revs up but will not shift in gear


The fluid being brown is a sign that the clutch packs have been slipping (burning out). You may have got to the point were the slipping has boiled the transmission fluid.

Feb 08, 2015 | Cars & Trucks

1 Answer

1997 Buick LeSabre Custom 3.8L has been shifting hard from park to reverse. My son was driving to work and said smoke or steam was coming inside the car from the defrost vents on the dash, the rpms were...


Hi, smoke or steam is likely coolant, possibly from bad heater core. Unrelated to transmission. Transmission....if you already had the fluid and filter changed, it is likely the bands are slipping on the transaxle and it is time to replace it....check your fluid level first. Engine/transaxle warm on level surface in park.... If coolant level OK, if you can get it to go, drive it home. At least you will get it closer to home if the tranny goes completely out, lessening the potential tow bill. I'll always save a few bucks where I can. If the tranny is going out anyway, you cant really hurt it..MIke

Jun 20, 2011 | 1997 Buick LeSabre

1 Answer

Driving down the road and tranny started slipping so I pulled to the side of the road, then let the truck sit for 10 minutes, then the tranny worked again but within 1500 feet was slipping again, and will...


It sounds like you either have a dirty filter, or a solenoid is faulty in the transmission. Change the fluid and filter, put some Lucas transmission oil in it and see if that resolves the issue. If the solenoid is dirty then it will cause the transmission to shift improperly, the Lucas will clean it.

Apr 08, 2011 | Chevrolet Avalanche Cars & Trucks

1 Answer

Tranny slipping?


Dose it make a normal sound when you start the engine, then more then likely fly wheel ok, anf it's going to be the transmission, if not normal it's the fly wheel.

Jul 14, 2010 | 2006 Chevrolet Express

1 Answer

Symtoms of a bad timimg chain/belt...but ran real


Problem is not solved but I did change the fuel filter, coil pack,ICM and have proper fuel pressure to the motor. Car starts but dies right away. I cant seem to find out if the fob on the key ring has something to do with stopping the motor. This fob says Radio Key by Secure Key with a number 35077 stamped on this thing.. Still trying to find out what this is and does it effect the cars ability to run

Mar 15, 2010 | 2004 Oldsmobile Alero

1 Answer

Tramission is dumping fluid , the rear is not leaking, or the front seal is not leaking Sooo!what could the problem be?


it could be coming up the dip stick pipe? if the box is getting over heated becouse the oil cooler is blocked then the gear oil will boil up and in time it will cook your gear box up to the point it wont work any more
if your driving it very hard and its slipping a bit it will get very hot the oil boils away,,, as smoke!

Nov 15, 2009 | 1993 Dodge Dakota

1 Answer

My 1997 ford explorer overheated and the transmission slipped


Tranny fluid may have been contaminated with coolant since tranny cooler lines go to radiator or condensor.
I would fix your leak on radiator, then completely drain tranny fluid and filter and replace.

Aug 06, 2009 | 1997 Ford Explorer AWD

2 Answers

Tranny slips & wont shift past 2nd gear


Ok, you will need to first check the fluid level in this transmission. if the trans is sealed, you will need to take to the dealer for a fluid check. assuming that the fluid level is proper, this will usually be caused by a faulty transmission control module and faulty shift solenoids as well. these devices are located on and inside the trans and i recommend testing each device for flaws.


Most slips are the result of gear ware but, the solenoids and TCM will cuse this issue as well.

May 21, 2009 | 1998 Acura CL

1 Answer

Truck wont start


Check your crank sensor, it bolts to the block on right rear and goes down into the trans bellhousing . You might have got the wire pinched between the trans and the engine.

Mar 24, 2009 | 1995 Dodge Ram

Not finding what you are looking for?
1992 Ford F250 Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...