Question about 1994 Ford Explorer Limited

1 Answer

Need to now how to change lower ball joint drvers side

Bottom ball joint drivers side

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Try these two websites its www.autozone.com and the other one is www.alldatadiy.com

Posted on May 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the easiest way to replace the front drivers side lower ball joint on a 1998 Nissan Altima?Or would it just be easier to replace the lower control arm?The ball joint is definetly done-for.


just need to get a ball joint splitter , pronged shaped device that you hammer between the ball joint and control arm ,after stripping down the assembly, little tip, when fitting new ball joint apply slight pressure from below when tightening the nut , this will stop the joint from just spinning , i usually use a scissor jack for this

Jun 03, 2017 | Nissan Cars & Trucks

2 Answers

Creaking groan from front driver side tire


The creaking is coming from either the shock ,ball joint, or a-arm bushings. Have someone with you and one person pushing up and down, the other, safely feeling each component till the vibration can be felt. If it is in fact the ball-joint then as long as it is safe (not loose), then just add grease to it as needed and it should go away.

Jun 08, 2009 | 2000 Ford Ranger SuperCab

1 Answer

I have a 1994 Ford Bronco Xlt with a 302 V8 Automatic.. When the truck was on a lift the front passenger side wheel had alot of negative camber I believe.. The wheel was slanted like this \ . The stearing...


To check the joints jack the wheel off the ground by the lower control arm and putting one hand on the top of the wheel and the other on the bottom try moving the wheel in and out. If you can then one or both ball joints are bad. Have someone move the wheel and watch the joints you will see if one or both are bad. While the wheel is off the ground move the wheel from side to side, that will tell you if you have bad steering linkage. You don't have to hold the steering wheel straight when changing the joints. But you will need an alignment when your done. Note; When installing the new parts try to get them as close to up and down as you can. Also if you change the tie-rods count the turns and install the new tie-rods to the same turns.

Apr 12, 2013 | Cars & Trucks

1 Answer

Trying to change my upper ball joint. Passager side


For your problem,check out this few help links.

Click the link below to go through its procedure:----Upper Ball Joints inspection and replacement? http://howtobyme.blogspot.in/2012/02/upper-ball-joints-inspection-and.html------- How to Test Upper and Lower Ball Joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-test-lower-ball-joint.html------- How to inspect Upper and Lower Ball joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-inspect-lower-ball-joint.html------ How to Service Ball Joints on Car? http://repairhelpcenter.blogspot.com/2011/12/how-to-service-lower-ball-joints-on-car.html----------- How to Replace Ball joints? http://repairhelpcenter.blogspot.com/2011/12/how-to-replace-lower-ball-joints.html--------- Lower Ball Joints replacing on Mitsubishi car? http://howtobyme.blogspot.in/2012/02/lower-ball-joints-replacing-on.html
-------------These details will help.For more help,keep updated,with car brand,model and year.Thanks.Helpmech.

Oct 05, 2012 | Cars & Trucks

1 Answer

How to change a Xantia bottom ball joint


Depressurize the hydraulic system. Jack the front and put on jack stands (both left and right side). Remove wheels. Slacken and unscrew the ball joint nut partially. Release ball joint from knuckle using a proper separation tool. Once dislodged, remove ball joint nut and pull out strut/knuckle away from lower arm. You may need to push down the arm with a lever. Remove dust cover from the ball joint. The ball joint can be removed by unscrewing it using a tool that locks into the notches on the sides of the ball joint. Install new one by screwing in the ball joint back into the knuckle.Tighten well.

Sep 01, 2012 | 1998 Citroen Xantia

1 Answer

How to replace a lower ball joint on 2004 mercury mountaineer?


Remove the brake caliper by removing the two bolts that connect it to the steering knuckle. Remove the lower ball joint cotter pin and retaining nut. Pry the steering knuckle up and away from the lower ball joint. Unscrew the grease fitting from the bottom of the lower control arm. Press the lower ball joint out of the control arm using a ball joint remover set.
Press the lower ball joint into the control arm using a ball joint installation tool. Remove the block of wood supporting the upper control arm. Install a new cotter pin through the ball joint stud.Install the grease fitting on the bottom of the ball joint. Use a c-clamp to push the piston back into the brake caliper. Reinstall the wheel assembly. Here you can find the quality parts http://www.buyautoparts.com/steering_system.htm

Aug 29, 2011 | Mercury Mountaineer Cars & Trucks

1 Answer

Ball joint repair and how do you do it


To perform the following procedure, the lower control arm must be removed from the vehicle. Refer to Removal And Installation for that procedure.

  1. Using a screw driver or other suitable tool, pry the seal boot off of the ball joint assembly
  2. Position receiving cup, Special Tool 6758 to support lower control arm when removing ball joint assembly. Install Remover, Special Tool 6919 on the top of the ball joint assembly.
  3. Using the arbor press, press the ball joint assembly completely out of the lower control arm.

NOTE: When installing ball joint in lower control arm, position the ball joint in control arm so notch in ball joint stud is in the direction shown. This will ease assembly of the ball joint to the steering when installing pinch bolt.

  1. By hand, position ball joint into ball joint bore of lower control arm. Be sure ball joint is not cocked in the bore of the control arm, this will cause the ball joint to bind when being pressed into control arm.

 

  1. Position control arm with installed ball joint, in an arbor press with Receiving Cup, Special Tool 6758 supporting the lower control arm. Then center Installer, Special Tool 6908-4 on the bottom of the ball joint
  2. Carefully align all pieces. Then press the ball joint into the lower control arm until it is completely seated against surface of lower control arm. The ball joint is correctly installed when there is no gap between the ball joint and the lower control arm. Do not apply excessive force against the ball joint or the lower control arm.
  3. Install a NEW seal boot by hand as far as possible on the ball joint. Installation of the seal boot is to be with the shield positioned as shown.

CAUTION: Do not use an arbor press to install the sealing boot on the ball joint. Damage to the sealing boot will occur if excessive pressure is applied to the sealing boot when it is being installed.

  1. Place Installer, Special Tool 6758 over seal boot and squarely align it with bottom edge of seal boot. Apply hand pressure to Special Tool 6758 until seal boot is pressed squarely against top surface of lower control arm.

CAUTION: A replacement ball joint is not pre-lubricated. Properly lubricate the replacement ball joint using Mopar Multi-Mile grease or an equivalent. Lubricate ball joint after seal boot is installed but prior to top of seal boot being pushed down below notch in ball joint stud. Air must vent out of the seal boot at notch when grease is pumped into ball joint, failure to do so will balloon and damage seal boot. Do not over grease the ball joint, this will prevent the seal boot from pushing down on the stud of the ball joint.

CAUTION: After the ball joint is properly greased, clip the end of the grease fleeing off below the hex. The ball joint seal boot is non-purgeable and further greasing is not required and can result in damage to the seal boot.

  1. Reinstall lower control arm on vehicle.

Mar 07, 2011 | 2000 Dodge Caravan

1 Answer

Drivers side upper ball joint replacement


It appears your car only has lower ball joints, the link below will take to detailed instructions on how to replace the lower ball joints.

Lower Ball Joint Replacement Instructions

Please rate my advise.

Jan 14, 2011 | 1988 Toyota Camry

3 Answers

How many ball joints does a 99 dodge stratus have?


It has two,lower ball joints,one on each side.

Feb 11, 2010 | 1999 Dodge Stratus

2 Answers

Ball Joint connecting lower control arm and spindle 99 Grand Prix


put a jack stand under the ball joint lower car, this applies pressure on the ball joint so the shaft of the ball joint does not turn.
heat the nut as well.

May 12, 2009 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
1994 Ford Explorer Limited Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...