Question about 2007 Hyundai Azera Limited Sedan

1 Answer

To repair my rolled over Azera

I need Front Windshield
Rear windshield
Both front door windows
Sunroof

Posted by on

  • yadayada
    yadayada May 11, 2010

    This is not a parts locator site, check the local wrecking yards and run a Goggle search.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Contact a Hyundai Parts Department for the door windows and sunroof. You can get aftermarket windshield and rear window by shopping around.

Posted on May 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why aren't electric windows, sunroof and windshield wiper delay and slow speed working?


[PDF]mini body control module - BMW-Planet.com

www.bmw-planet.com/lib/mini/BODY%20CONTROL.pdf
Always check ALL the fuse that supply power to the BC1. ... the heated rear windowand optional heated front screen until the voltage level exceeds 12.2 ... Convenience Opening and Closing of windows and sunroof ..... intermittent wipe, slow, and fastspeeds. .... Road speed has no influence over wiper speed 1 (Slow).

Nov 19, 2015 | Cars & Trucks

1 Answer

How many airbag sensors in a 2008 gmc acadia


1) Front End Sensor - Right--Located under the front hood in the engine compartment (2) I/P Air Bag--Located at the top right under the instrument panel (3) Roof Rail Air Bag - Right--Located under the headliner, extending from the passenger front windshield pillar to the passenger rear windshield pillar (4) Side Impact Sensor (SIS) - RF--Located under the right front door trim near the lower rear of the door frame (5) Sensing and Diagnostic Module (SDM)--Located underneath the vehicle carpet under the center console (6) Seat Belt Pretensioner - RF--Located under the trim near the bottom of the center pillar (7) Side Impact Sensor (SIS) - RR--Located under the right rear door trim near the lower rear of the door frame (8) Roof Rail Module - Right--Located behind the garnish molding on the upper rear pillar (9) Roof Rail Module - Left--Located behind garnish molding on the upper rear pillar (10) Side Impact Sensor (SIS) - LR--Located under the left rear door trim near the lower rear of the door frame (11) Seat Belt Pretensioner - LF--Located under the trim near the bottom of the center pillar (12) Side Impact Sensor (SIS) - LF--Located under the left front door trim near the lower rear of the door frame (13) Roof Rail Air Bag - Left--Located under the headliner, extending from the driver front windshield pillar to the driver rear windshield pillar (14) Steering Wheel Air Bag--Located on the steering wheel (15) Vehicle Battery--Located at the front left of the engine compartment. (16) Front End Sensor - Left--Located under the front hood in the engine compartment

Aug 12, 2015 | GMC Cars & Trucks

2 Answers

How to install replacement sunroof motor on a 1999 Pontiac grand prix


Important: This sunroof system is timed from the factory in order to allow the actuator to shut off automatically when the sunroof window reaches a certain position. Use extreme care when removing the actuator from the sunroof module. This may cause the timing to be thrown off. This may damage to the sunroof. Anytime the actuator needs to be removed from the module, ensure that the sunroof window is in the fully closed position.
Remove the sunroof window. Refer to Sunroof Glass Panel Replacement .
Slide the sunshade fully rearward. Move the sunroof window to the vent position. Remove the sunroof screws (two on each side). Remove the sunroof window from the module.
Place the sunroof module in the fully closed position. Remove the headliner. Refer to Headlining Trim Panel Replacement in Interior trim.
Tools Required ?€¢
J 38778 Door Trim Pad and Garnish Clip Remover


?€¢
J 2772-C Headliner Installer

  1. Remove the sunshades. Refer to Sunshade Replacement .
  2. Remove the overhead console, if equipped. Refer to Roof Console Replacement .
  3. Remove the sunshade retainers. Refer to Sunshade Anchor Replacement .
  4. Remove the power sunroof switch, if equipped. Refer to Sunroof Switch Replacement in Roof.
  5. Remove the sunroof trim lace, if equipped. Refer to Sunroof Seal/Molding Replacement in Roof.
  6. Remove the dome light, if equipped.
  7. Remove the coat hooks. Refer to Coat Hook Replacement .
  8. Remove the assist handles. Assist Strap Replacement
  9. Remove the rail lamp. Refer to Roof Side Rail Lamp Replacement in Lighting.
  10. Remove the windshield side garnish molding. Refer to Windshield Pillar Garnish Molding Replacement .
  11. Remove the upper quarter trim panels. Refer to Rear Quarter Upper Trim Panel Replacement .
  12. Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement .
  13. Pull down on the door opening weatherstrip seal on both the front and the rear doors.
  14. Remove the 2 rear retainers (2) using J 38778 Door Trim Pad and Garnish Clip Remover. Disconnect the headliner electric harness at the right side of the rear window shelf. Rotate the right front seatback to a horizontal position. Remove the headliner from the vehicle through the right front door.
Disconnect the electrical connector from the actuator.
Important: Before removing the actuator, ensure that the pins J 41718 are tight and holding the cable.
Thread the J 41718 into the front sunroof window screw hole in order to retain the cable adjustment. Remove the sunroof actuator screws. Remove the sunroof actuator from the module. Did you look for a video on youtube ?

Feb 27, 2015 | 1999 Pontiac Grand Prix

1 Answer

Wet carpet passenger side


DRAIN HOLES IN BOTTOM OF DOORS? UNDER BONNET BELOW WINDSCREEN CAN COLLECT A LOT OF STUFF

Jan 23, 2014 | Jaguar S-Type Cars & Trucks

1 Answer

Why does my 2006 RT Charger with sunroof leak from the overhead light near the windshield? The sunroof remains dry


check to see if the drain hose is blocked,there's one on each side front corner of sunroof that go down through roof supports,along each side of windshield

Feb 10, 2013 | Dodge Charger Cars & Trucks

1 Answer

I have a 1999 chevy blazer I cannot close the


The sunroof is powered by the same circuit breaker that power's your power window, so if your windows work than the circuit breaker should be good. You needed test the switch to verify if works with; on the factory sunroof system the roof is controled by a sunroof module the module receives a signal from the switch then throws voltage to the sunroof motor. The motor and module are located between the sunroof assembly and windshield underneath the head liner. You would reconnected the switch and test to see if the sunroof motor is getting power when the switch is in use by testing the dark green wire when closing and a light green wire when opening. Test these wires at the sunroof motor with a ohm meter or test light. Also, check this procedure to repair...

GM S-Series Pick-ups and SUV's 1994-1999 Repair Guide Power Sunroof - REMOVAL & INSTALLATION

Glass
  1. Close the sunroof and open the sunshade.
  2. If the piece of glass being removed is to be reinstalled, mark the location of the screws, this will ensure proper alignment during installation.
  3. Unfassten the screw that attach the sunroof glass to the sunroof assembly.
  4. Remove the glass from the vehicle.
To install:
  1. Place the glass into position and install the screws that retain the glass. Do not fully tighten the screws just yet.
  2. Adjust the glass so that the fit between the glass and the opening is equal at all four sides. The rear edge of the glass may be slightly higher than the front edge to reduce the wind noise.
  3. After the glass has been adjusted, tighten the screws to 31 inch lbs. (3.5 Nm).
  4. Check the operation and fit of the glass.

Motor
  1. Disconnect the negative battery cable.
  2. Remove the sunroof opening trim by starting at the **** joint and pulling the trim strip from the sunroof opening.
  3. Remove the headlines as follows:
    1. If equipped, remove the overhead or sunroof console.
    2. If equipped, remove the dome lamp.
    3. Remove the coat hooks and the assist handles.
    4. Remove the sunshade-to-roof screws, while pulling down on the sunshade base, push in on the extended screws, loosen the screw that attaches sunshade to the roof and pull down on the sunshade retainer while pushing in on the extended screw. Remove the retainer.
    5. Remove the windshield garnish moldings using trim removal tool J 38778 or its equivalent. Pull the molding away from the pillar and up to remove it.
    6. On four door models, remove the body lock pillar trim panels.
    7. Remove the roof rear header garnish molding using the trim removal tool. Insert the tool into the front edge of the trim and work along the front of the panel, from one end to the other. Unplug the cargo lamp electrical connection and remove the trim.
    8. On two door models, remove the rear seat upper seat belt anchor bolts.
    9. Remove the upper and lower front seat belt anchor bolts.
    10. Remove the rear seat belt lower anchor nut (two door models only).
    11. Remove the end gate or liftgate opening sill plate.
    12. Remove the jack storage cover (left side).
    13. Remove the upper body side trim panel screw (left side).
    14. Remove the upper body side trim panel and the body side front lower trim panel.
    15. Remove the headliner from the vehicle.
  4. Remove the sunroof console mounting bracket.
  5. Remove the straps that retain the wiring harness.
  6. Tag and unplug any necessary electrical connections.
  7. Unfasten the screws that attach the motor to the sunroof assembly.
  8. Remove the motor from the vehicle. Make sure that you do not move the sunroof mechanism while the motor is not in place.
To install:
  1. Place the motor into position and install the retaining screws. Tighten the screws to 31 inch lbs. (3.5 Nm).
  2. Attach all electrical connections that were unplugged.
  3. Attach the straps that retain the wiring harness.
  4. Install the sunroof console mounting bracket.
New headliners must be pierced to accommodate actual vehicle accessories.
  1. Install the headliner as follows:
    1. Install the body side front lower trim panel and the upper body side trim panel.
    2. Install the upper body side trim panel screw (left side).
    3. Install the jack storage cover (left side).
    4. Install the end gate or liftgate opening sill plate.
    5. Install the rear seat belt lower anchor nut (two door models only). Tighten to 59 ft. lbs. (80 Nm).
    6. Install the upper and lower front seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
    7. On two door models, install the rear seat upper seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
    8. Install the roof rear header garnish molding. Attach the cargo lamp electrical connection, place the trim in position and engage the molding retainers.
    9. On four door models, install the body lock pillar trim panels.
    10. Install the windshield garnish moldings. Place the molding into position, align the retainer clips with the slots and press into place.
    11. Place the sunshade retainer in position, install the screw and tighten to 10 inch lbs. (1.1 Nm). Position the sunshade, install the screws and tighten to 10 inch lbs. (1.1 Nm).
    12. Install the coat hooks and the assist handles.
    13. If equipped, install the dome lamp.
    14. If equipped, install the overhead or sunroof console.
  2. Install the sunroof opening trim. Start the trim in the center of the front of the sunroof opening and work around the perimeter.

Hope helps (remember rated this) Good luck.

Jun 03, 2010 | 1999 Chevrolet Blazer

1 Answer

Leak on front passenger floor only when strong rain .


This is just a shot in the dark-- but ya never know, right? If you have a sunroof check the drains. They are lines that typically run from the inner corners of the sunroof housing down to empty out at the low point on the vehicle body. You may find the opening on the inside door jamb near the hinges, or on the pillar between front & rear doors. Look for a little nipple type rubber fitting.
Another thought...have you checked your heater core and hoses?
Good luck!

Feb 25, 2010 | 1998 Jeep Grand Cherokee

1 Answer

Interior Carpet Getting Wet


It sounds like a plugged drain line from the air conditioner. Most cars now run in the a/c mode whenever u turn on the climate control (even when heat is on). The passenger side front is where it would be wet, and the carpet and carpet pad act like a sponge and will soak up the water. Let me know how u make out.

Oct 25, 2008 | 2003 Honda Accord

Not finding what you are looking for?
2007 Hyundai Azera Limited Sedan Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...