Question about 2007 Nissan 350Z

Open Question

How to replace rear window wiper blade on 350Z

The rear window wiper blade arm appears to be locked in position as I cannot raise it to take off the old blade - do you know how to raise the arm?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 97 nissan sentra windshield wiper linkage arm disconnected

Most likely you will have to replace the wiper linkage from the center pivot to the left or drivers-side wiper pivot. The plastic piece in the linkage gets brittle over time and breaks down. To save a hassle in the future, replace both linkages. It should be under $20.00 for parts.

Posted on Sep 14, 2008

  • 512 Answers

SOURCE: Jeep Liberty Rear Wiper Blade

you should be able to raise it just enough to disengage it from the park ramp according to jeep...if that doesnt work try turning it on then shutting key off in mid stride

Posted on Oct 01, 2008

bibleman01
  • 334 Answers

SOURCE: remove rear wiper blade on saab 9-5 estate

Best way go to a parts store and ask for help and they would probably slip it on for you
God Bless you Greg

Posted on Dec 03, 2008

stormbrewin
  • 426 Answers

SOURCE: front blades not working fuse ok

The motor is usualy central to the wiper arms and either bolted to the firewall or inside the plenum chamber at the bottom of the windscreen.If you can hear the motor you can find it, track it down by listening.Your probly right about linkage however if that is the case you should be able to move the wipers with your hand and they should move freely if they dont you may have other problems.

Posted on Dec 17, 2008

dgjtex
  • 405 Answers

SOURCE: 04 dodge ram 1500 wiper arm goes down before going up

remove wiper arms at the shaft, right at the cowl. each will have a nut on them but it is covered by a piece of plastic that will snap up for access. take nuts off and remove wiper assembly. turn key on turn wipers on make sure shafts turn when on, then turn off the shafts to stop in park position. then reinstall wiper assemblies in their park position .

Posted on Dec 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the rear wiper arm on my Hyundai getz 2006


If it has a plastic cover then there will be a retaining nut under it that holds the arm on the post, if not raise the wiper arm up and pull out the little blade lock with a pocket screwdriver.

Apr 14, 2017 | Hyundai Cars & Trucks

1 Answer

I need to have 'step-by-step' instructions for replacing the driver side windshield wiper arm on my 2000 Ford Explorer. Can you help me with this?


  • Turn your wipers off, using the stalk on the left side of your steering column. Turn your ignition off and remove the key.

  • 2

    Pull the wiper blade up to lift it to the service position. Pull the front part of the blade down to position it at an angle.

  • 3

    Pull back the lock pin on the center part of the wiper blade (where it connects to the wiper arm). This unlocks the blade from the wiper arm.

  • 4

    Grasp the blade on each side and pull it down (away from the extended wiper arm) to release it from the "U" clip.

  • 5

    Repeat the process for the other wiper blade, if desired. Removing the driver's side and passenger's side wiper blade is the same.

  • 6

    Install the new wiper blade. Open the lock pin on the new blade, and then insert it into the wiper arm "U" clip. Close the lock pin and lower the wiper blade to its normal position.

  • Jan 29, 2011 | Ford Explorer Cars & Trucks

    1 Answer

    How do you replace the rear wiper on a 2009 Scion XD?


    You can make use of following procedure to replace rear wiper in ur scion xd.
    Pull the rear wiper arm away from the rear window in order to access the wiper blade.

  • Locate the hinge where the blade mechanism meets the wiper arm and squeeze the plastic tabs on the blade in order to release it from its locked position on the arm. In some cases, instead of tabs, there is a small button that must be pressed to release the wiper from the arm.
  • Detach the blade from the arm and slide the old blade out. Insert the new blade into the wiper arm and lock the blade in place.
  • Return the wiper arm to its set position. Before driving, wet the window and test the wiper to make sure it is operating properly.
  • Dec 14, 2010 | 2009 Scion xD

    1 Answer

    How do I replace wiper blades


    First, pull on the wiper arm until it raises and locks into the service position. The wiper arm will stand by itself once you raise it past a certain point.
    Then find the clip on the underside of the wiper arm (rotate the blade slightly to get to it.
    Press the clip in while simultaneously pulling the old wiper blade off the wiper arm. You can then discard the old blade.
    Align the new wiper blade with the wiper arm track. Slide it along the track until you hear it click.
    Repeat this process with the other wiper blade to complete the replacement of wiper blades on your Highlander.
    Return the wiper arms to their normal position against the windshield. Done!

    Dec 05, 2010 | 2005 Toyota Highlander

    1 Answer

    I need to adjust the wiper arm on a 1997 suburban, it hits the side of the window.


    Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:
    1. Turn ignition switch to ACCY position.
    2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
    3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.
    To Install:
    1. Insert wiper arm hook through opening in wiper blade.
    2. Place wiper blade pivot in the inside radius of wiper arm hook.
    3. Pull on wiper blade pivot into hook until it locks into place.
    4. Check wipers for proper operation.
    Wiper Arm To Remove:
    NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.
    1. Remove washer hose.
    2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
    3. Remove wiper arm from shaft.
    To Install:
    1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
    2. Press arm assembly on shaft and push retaining latch IN.
    3. Connect washer hose.
    4. Remove windshield markings and check wipers for proper operation.
    prev.gif next.gif

    Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

    1 Answer

    Windsheild wiper does not remain in contact for the full stroke.The blade actually raises off the windsheild.1995 volvo wagon. three sets of blades, two sets replaced by mechanics.


    Try this:

    With ignition on, turn on wiper switch. When wiper arm gets to point where blade does not touch screen, turn off ignition switch so that wipers do not return to park position. It may take a few goes to stop arm in the right position so repeat process until it is in the best position.

    Check main wiper arm and bend slightly towards windscreen so that blade touches screen and there is some spring pressure from the arm to keep blade on screen. Also check that there is no interference between main arm and the section which supports the rubber blade. If you get blade chatter as the arm sweeps, twist the end of the main arm slightly in the opposite direction to the movement that produces the chatter. It may take a bit of trial and error to get it all right.

    Oct 04, 2010 | Volvo 850 Cars & Trucks

    1 Answer

    I installed a new wiper motor. I ran it before installing the wiper arms. it will not stop at zero. it over travels down into the cowling. I try to rest them higher then they stop some where in the middle...


    Try to run the motor without the wiper arms tightened down and turn it off so it can cycle down to its rest state. Then install the wiper arms.

    Make sure, that the car's windshield wiper wiring is correct for this motor.
    ---
    Wiper Arm & Blade Removal & Installation Front To Remove:
    CAUTION
    When the wipers are parked (off), the driver’s wiper arm must be above the passenger’s wiper arm.
    1. Remove the clip holding the outside end of the wiper arm cover to the arm.
    2. Lift the arm cap up to expose the nut.
    3. Remove the wiper arm mounting nut.
    4. Using a suitable two jaw puller, remove the wiper arm from the wiper pivot.
    To Install:
    1. Verify that the wiper motor and linkage are in the parked position.
    2. Place the wiper arm in position over the wiper pivot.
    3. Install the nut to hold the wiper arm to the wiper pivot. Torque nut to 26 ft. lbs. (35 Nm). CAUTION
      Make sure to tighten the wiper arm nut properly.
    4. Push the arm cap cover down.
    5. Secure the clip holding the cover to the wiper arm.
    Rear To Remove:
    1. Lift and hold the wiper arm away from the rear window.
    2. Lift the lock securing the wiper arm to the pivot.
    3. Slowly release the wiper arm so it rests against the lock.
    4. Remove the wiper arm from the pivot.
    To Install:
    1. Install the wiper arm on the pivot.
    2. Pull the arm outward and release the lock.
    3. Gently release the wiper arm until it rests on the rear window.
    prev.gif next.gif

    Aug 22, 2010 | 1996 Dodge Grand Caravan

    1 Answer

    How to replace the wiper insert at the back of


    moz-screenshot.jpg
    1. REMOVE RR WIPER BLADE
      1. Raise the rear wiper blade to the position as shown in the illustration where the meshing of the claw disengages with a clicking sound. NOTE: Be careful not to break the claw.
      2. Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.1722d05.gif

    1. REMOVE REAR WIPER RUBBER
      1. Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
    f54b10a.gif
    1. INSTALL REAR WIPER RUBBER
      1. Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
    0dd144d.gif
    b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
    8f40009.gif
    c. After passing the rear wiper rubber through the rear end side claw, protrude it from the rear end stopper and pass it through the front tip side claw.

    Sep 12, 2009 | 2005 Toyota Matrix

    1 Answer

    No instructions on how to remove rear wiper blade on 2004 Town & Country touring. The wiper arm only raises about three inches from window, and there is no indication of a normal wiper removal at that...


    there is a plastic cap where the arm connects to a post. pop this cap off with your finger nail or small screw driver. this cap hides a nut. remove the nut (10mm socket needed?) and pull the arm off to replace the blade

    May 16, 2009 | 2004 Chrysler Town & Country

    1 Answer

    Jeep Liberty Rear Wiper Blade


    you should be able to raise it just enough to disengage it from the park ramp according to jeep...if that doesnt work try turning it on then shutting key off in mid stride

    Sep 25, 2008 | 2002 Jeep Liberty

    Not finding what you are looking for?
    2007 Nissan 350Z Logo

    Related Topics:

    824 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    74945 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    705 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...