Question about 1995 Honda Accord

1 Answer

Set timing what way all pulley marks line up to, camshaft,crank,etc. set timing on 95 honda accord 4 cyclr.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

V teck or single, single cam says up on it crank has 2 b on combustion duall cams r facuing each other crank d same
easy call me 559 5796874 california

Posted on May 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set the timing on a 1994 Toyota Tercel with timing belt removed


Refit timing cover , line up marks on crank pulley with mark on timing cover T D C, turn camshaft till No. 4 cylinder valves are just rocking , line up marks on crank gear with mark on head or block, we now have compression stroke on No. one cylinder, fit belt and rotate engine and recheck marks

May 02, 2017 | 1994 Toyota Tercel

1 Answer

How do I set timing on a 97 honda civic dx


On the crankshaft the is a "dot" on the timing gear(behind the crank pulley), it has to line up with an arrow on the oil pump housing(the arrow will be toward the back of the car. Then for the camshaft, it has 3 little "dash" marks on the pulley, two have to be lined up with the cylinder head, and the third will be pointing up!

Apr 27, 2012 | 1998 Honda Civic

1 Answer

How to set the time belt?


4 Cylinder diesel(4JX1) :
1 - Timing mark
2 - Cam pulley
3 - HP Oil pump pulley
4 - Tensioner pulley


suzman_0.jpg

6 Cylinder petrol:
Align crank(C) timing notch mark (1) to oil pump mark.
Align cam pulley(L+R) marks(3) to cylinder head marks
The cam belt has 3 marks, 2 lines and one mark that is actually a row of dots. Align the dots to the crank pulley groove mark(2) and align the other 2 lines to the cam pulley marks. Using a clothes peg to hold the belt to the cam pulleys works wonders to keep it in place while fitting. Please note the arrows on the belt and have them point in the direction of rotation - right to left side of engine
W - water pump pulley
I - Idler pulley
T - Tensioner pulley.

If for some reason you need to realign the cams on each bank :
Standing in front of the car and starting from YOUR left , looking at the cams you should see RE, RI, LI, LE on each of the camshafts.(R for right bank, L for left bank, I for intake and E for exhaust) Right bank camshafts are marked with one dot, left bank with 2 dots on the shaft itself. To align the camshafts to each other each cam shaft gear has a mark on it. Draw an imaginary line between the centre of the camshaft and the centre of the pulley. The alignment mark should be between the two along this imaginary line. The result will be that RI an RE will be at the top of each gear. The same with the left bank.


suzman_2.jpg

Nov 08, 2010 | 1998 Isuzu Rodeo

1 Answer

How do you set the timming on a 95 honda accord


1990–95 4-Cylinder Accord and 1992–95 Prelude
  1. .
  2. Fig. 10: On all engines except VTEC, the belt adjuster arm must be locked in place using one of the lower cover mounting bolts 86803136.gif
    NOTE: There are two belts in this system; the one running to the camshaft pulley is the timing belt. The other, shorter one drives the balance shaft and is referred to as the balancer belt or timing balancer belt. Use a piece of chalk or a marker to place an identifying arrow on the belts. The arrow can identify the direction of rotation or the outer edge of the belts. The belts must be reinstalled so it moves in the same direction. Protect the belts from oil, coolant, etc. It's an even better idea to replace the belts at this point.
  3. Loosen the timing belt adjustment nut. Push on the tensioner to relieve tension from the balancer belt, then tighten the nut. Remove the balancer belt.
  4. On all models except Prelude with VTEC, loosen the lockbolt installed earlier and the adjusting nut. Push on the tensioner to release the timing belt, then tighten the nut. Carefully remove the timing belt. On Prelude VTEC models, remove the timing belt from the pulleys, then remove the bolts securing the auto-tensioner. Remove the auto-tensioner from the engine. To install:
  5. Check the position of the timing marks. The timing pointer must be perfectly aligned with the TDC (white mark) on the flywheel or flex-plate; the camshaft pulley must be aligned so that the word UP is at the top of the pulley and the marks on the edge of the pulley are aligned with the surfaces of the head. Additionally, the face of the front timing balancer pulley has a mark which must be aligned with the notch on the oil pump body. This pulley is the one to the left crank when viewed from the pulley end.
  6. Fit the timing belt over the pulleys and tensioner. On DOHC engines without VTEC, remove the 5mm pin punches from behind the cam pulleys.
  7. Except Prelude VTEC models:
    1. Temporarily install the crank pulley and bolt.
    2. Loosen the tensioner adjusting nut 1 turn, then tighten it. Rotate the crankshaft counterclockwise until the camshaft pulley has moved 3 teeth to create tension on the belt. Loosen the nut again, then tighten it to 33 ft. lbs. (45 Nm). NOTE: Always rotate the crankshaft counterclockwise when viewed from the pulley end. Rotating it clockwise will cause improper adjustment and possible damage.
    3. Tighten the lockbolt installed earlier to lock the timing belt adjuster arm. Remove the crank pulley.
  8. On Prelude VTEC models:
    1. Hold the auto-tensioner with the maintenance bolt facing up. Loosen and remove the bolt. NOTE: Handle the tensioner carefully so the oil inside does not spill or leak. Replenish with clean engine oil if any does leak. Total capacity is 1⁄4 fl. oz. (8 ml).
    2. Clamp the mounting flange of the tensioner in a vise using a cloth or blocks of wood to protect it. Insert a flat blade screwdriver into the maintenance hole. Place the stopper (tool number 14540-P13-003) or an equivalent clamp on the tensioner, then turn the screwdriver clockwise to compress the bottom. Be careful not to damage the threads or the gasket contact surface.
    3. Install the maintenance bolt on the tensioner with a new gasket. Tighten to 6 ft. lbs. (8 Nm).
    4. Make sure no oil is leaking from around the maintenance bolt, then install the tensioner on the engine. Make sure the stopper stays in place and tighten the bolts to 16 ft. lbs. (22 Nm).
    5. Remove the stopper. Fig. 11: On VTEC engines, the tensioner must be compressed before installing it on the engine 86803137.gif
      Fig. 12: Remove the stopper after installing the tensioner on the engine 86803138.gif

  9. Make sure all timing marks are positioned correctly (as described earlier).
  10. Align the rear timing balancer pulley (to the right of the crank pulley) using a 6x100mm bolt or rod. Mark the bolt or rod at a point 2.913 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the rod into the hole. Align the 74mm mark with the face of the hole. This pin will hold the shaft in place during installation.
  11. Loosen the tensioner adjusting nut and verify that the timing balancer belt adjuster moves freely. Fig. 13: The balancer shaft must be held in position during timing belt installation 86803139.gif

  12. Fit the balancer belt over the pulleys. Remove the bolt or rod from the maintenance hole.
  13. Temporarily install the crank pulley. Rotate the engine one turn counterclockwise, then tighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm). Double check the positions of the timing marks and make sure they still line up. If not remove the belts and repeat the procedures. NOTE: Both belt adjusters are spring-loaded to properly tension the belts. Do not apply any additional pressure to the pulleys or tensioners while performing the adjustment.
  14. Remove the crank pulley. Remove the lockbolt installed earlier on the timing belt adjuster arm. Install the maintenance bolt with a new washer. Tighten it to 22 ft. lbs. (30 Nm).
  15. Install the lower cover, making certain the rubber seals are in place and correctly located. Tighten the retaining bolts to 9 ft. lbs. (12 Nm).
  16. If applicable, raise the lower beam and engine into place. Install the rear bolts for the lower beam. Tighten them to 28 ft. lbs. (39 Nm) on 1990–91 Accords, 37 ft. lbs. (50 Nm) on 1992–95 Accords and 43 ft. lbs. (60 Nm) on 1992–95 Preludes.
  17. Install the key on the crankshaft and install the crankshaft pulley. Apply oil to the bolt threads and tighten it to the following:
    • 1990 Accord: 166 ft. lbs. (230 Nm)
    • 1991–93 Accord: 159 ft. lbs. (220 Nm)
    • 1992–93 Prelude: 159 ft. lbs. (220 Nm)
    • 1994–95 Accord and Prelude: 181 ft. lbs. (245 Nm)
  18. Install the dipstick tube and dipstick.
  19. Install the side engine mount (refer to engine removal and installation for procedures). Remove the jack from under the engine.
  20. Install the upper belt cover.
  21. Install the side engine mount support bracket if it was removed.
  22. Install the valve cover.
  23. Install the compressor and/or alternator drive belt; adjust the tension.
  24. Route the wiring harness over the valve cover and connect the wiring to the alternator.
  25. Install the power steering pump and install the belt.
  26. Reinstall the cruise control actuator. Connect the vacuum hose and the electrical connector.
  27. Double check all installation items, paying particular attention to loose hoses or hanging wires, untightened nuts, poor routing of hoses and wires (too tight or rubbing) and tools left in the engine area.
  28. Refill the engine coolant.
  29. Install the splash shield under the engine.
  30. Connect the negative battery cable.
  31. Start the engine, allowing it to idle. Check for any signs of leakage or any sound of the belts rubbing or binding.

Jul 18, 2010 | 1995 Honda Accord

1 Answer

How to line crank and cam for timing belt on 1988 no crank marks


Hard to explain here... but I believe that car also has the balance shaft which needs to be timed as well. The camshaft has 2 lines which line up to the top of the head, and a "up" or "top" mark at the top.
Crank is set to 0 degrees.

May 02, 2010 | 1988 Honda Accord 4 Door

2 Answers

1995 Honda Passport timing alginment 3.2 ltr 6VD1 engine


The crankshaft should have the timing mark on the crank pulley (Notch in the outer edge of the pulley near the keyway) It should align with the timing mark on the oil pump. (With the keway turned to about the 3 O'clock position.)

Align the marks on the camshaft timing pulleys with the corresponding dots on the front plate.

If you are installing a new belt, it should have 2 solid white lines printed on it that you would align with the timing marks on the cams and a dotted white line to align with the timing mark on the crank.

It makes a difference which way you put the belt on. (Which edge faces the front of the engine.) Most, but not all brands of belts have arrows and the word "FRONT" on them to tell you which edge of the belt shoud face the front of the motor. If there is no mark to tell you which edge is front, the letters on the belt must be able to be read correctly as viewed from the front of the vehicle.

Oct 30, 2009 | Honda Passport Cars & Trucks

1 Answer

Need diagram showing timing adjustment for a 1992 honda accord 2.2 engine see no timing marks how do i set timing


Check the position of the timing marks. The timing pointer mustbe perfectly aligned with the TDC (white mark) on the flywheel orflex-plate; the camshaft pulley must be aligned so that the word UP isat the top of the pulley and the marks on the edge of the pulley arealigned with the surfaces of the head. Additionally, the face of thefront timing balancer pulley has a mark which must be aligned with thenotch on the oil pump body. This pulley is the one to the left crankwhen viewed from the pulley end.

Also, in here, 1994-Honda-Accord-Coupe-Section-01-Engine (page 47 and next / TDC marks) you can find referenece information about Accord Engine.

If you need more details, visit autozone.com (free register) and select your model vehicle.

I hope help you (remember rated this help) Good luck.

Sep 25, 2009 | 1992 Honda Accord

1 Answer

I have a 1996 Honda Accord and I have replaced the timing belt...I need to know if anyone can help me with the camshaft and crankshaft markings.


There should be markings on the gears or pulleys for both parts. It would be a diamond or dot. The top part should be your cam and the mark would go on the bottom directly over the mark on the crank. The crank mark should be at high noon. They should not offset, they should be directly inline. Single overhead cam only.

Jul 07, 2009 | 1998 Honda Accord

1 Answer

Broken timing belt


hi the one on the crankshaft is on the timming sprocket behind the crank pulley the camshaft one is on the cam sprocket towards the bottom also line your balance shaft marks you if you lined them up ok and it wont, start test your compressions you may have a bent valve yates210456

Oct 08, 2008 | 1998 Honda Accord

Not finding what you are looking for?
1995 Honda Accord Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...