Question about 2003 Honda Accord

1 Answer

I have malfunction indicator lamp on how i can fix that

Have malfunction indicator lamp on how i cac fix that

Posted by on

  • tinda20 May 28, 2009

    thank you very much

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 4,369 Answers

Go to autozne and have them do free engine computer scan. They will tell you fault codes.

Or, try disconnecting the battery for 1/2 hour. Then reconnect and drive 10 miles. It may have fixed itself already.
MIL light on is not a big issue. only if flashing

Posted on May 27, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

StormStrikes
  • 104 Answers

SOURCE: Malfunction indicator lamp

The Malfunction Indicator Lamp or MIL (Also called the check engine light or service engine soon light) comes on when the on board computer detects an issue with the operation of the engine or transmission.

The best thing to do is to take the vehicle to an auto parts store like Autozone and have them hook up their scan tool to the vehicle and read the code. They can read it, tell you what it is and also tell you what the code means.

If it is pointing to a faulty component or sensor and you replace or repair the component the the light will go off on its own after the computer sees that the malfunction is no longer present.

You can have the code cleared, but if whatever caused the light to come on in the first place is not addressed then it will just come back on eventually.

Posted on Dec 31, 2008

beduncan
  • 73 Answers

SOURCE: Malfunction Indicator Lamp

Take your car to your local autoparts store and have them pull the codes - this is free at most stores. Post the codes when you're done. This can be caused by anything - even as simple as not tightening your gas cap (you should hear the clicks - it doesn't damage the cap).

Posted on Aug 07, 2009

  • 67 Answers

SOURCE: i have malfunction indicator lamp on how i can fix that

Same thing...Let them scan it so you can get the code

Posted on Feb 16, 2010

emissionwiz
  • 75197 Answers

SOURCE: malfunction indicator lamp in my toyota corolla is on how i fix?

The check engine light also called the malfunction indicator comes only when the computer control unit (called the PCM) senses a fault in the electronic controls of the engine and/or the emission system, there are about 200 possible faults that turn the light on, to know what has developed a problem you must have the system tested, this is called an OBD2 fault code test, Kragen and Autozone parts stores do this testing for free.

Posted on May 27, 2010

emissionwiz
  • 75197 Answers

SOURCE: malfunction indicator lamp illuminated on daewoo lacetti

The check engine light comes only when the computer control unit (called the PCM) senses a fault in the electronic controls of the engine and/or the emission system, there are about 200 possible faults that turn the light on, to know what has developed a problem you must have the system tested, this is called an OBD2 fault code test

Posted on Jun 02, 2010

Testimonial: "Thanks, You have confirmed what I thought needed to happen, will organise one tomorrow."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuses ok,light in dash tested and works. But check engine light does not come on when you turn on the ignition. What else should I check? This is a ford ranger XLT 4x4 4.0L V6-245cid engine (pushrod)


The instrument cluster (10849) carries out a display proveout to verify that all warning/indicator lamps and monitored systems are functioning correctly. When the ignition switch (11572) is in the ON position with the engine (6007) off, the following indicators will illuminate:
  • CHECK ENGINE/malfunction indicator lamp (MIL).
  • CHECK GAGE warning indicator.
  • Charge system warning indicator.
  • Anti-lock brake warning indicator (ABS).
  • Safety belt warning indicator (60second proveout).
  • Air bag indicator.
  • An indicator is inoperative - CHECK ENGINE/malfunction indicator lamp (MIL)
  • Bulb.
  • Circuitry.
  • Instrument cluster printed circuit.
  • Powertrain control module (PCM) (12A650).
  • GO to Pinpoint Test N .

Feb 15, 2016 | Cars & Trucks

1 Answer

Push button for four wheel drive isn't working


Do you have any lights on the dash lit ?
SERVICE indicator (4WD/AWD) Lamp
The SERVICE indicator (4WD/AWD) lamp is an integral part of the cluster and cannot be serviced separately. This lamp is used to inform the driver of the vehicle of malfunctions within the automatic transfer case (ATC) system. The SERVICE indicator (4WD/AWD) lamp is controlled by the transfer case shift control module via CKT 1567. this system will set DTC'S if there is a problem .
Diagnostic Trouble Codes DTC B2725 ATC Mode Switch Circuit Malfunction DTC C0300 Rear Speed Sensor Malfunction DTC C0305 Front Speed Sensor Malfunction DTC C0308 Motor A/B Circuit Low DTC C0309 Motor A/B Circuit High DTC C0310 Motor A/B Circuit Open DTC C0315 Motor Ground Circuit Open DTC C0323 T-Case Lock Circuit Low DTC C0324 T-Case Lock Circuit High DTC C0327 Encoder Circuit Malfunction DTC C0367 Front Axle Control Circuit High DTC C0374 General System Malfunction DTC C0376 Front/Rear Shaft Speed Mismatch DTC C0387 Unable to Perform Shift DTC C0550 ECU Malfunction DTC C0611 VIN Information Error you probably should take this to a repair shop !

This tt

Feb 22, 2015 | 1999 Chevrolet Silverado 1500

1 Answer

Why is the malfunction indicator lamp on?


the malfunction lamp is on to tell you that there is a fault in the system of the engine and/or gear box. It requires you to have the fault codes read and to have the fault fixed. It is there to notify you that something has gone wrong and to have it fixed before it becomes expensive.

Jun 20, 2014 | 1994 Volvo 850

1 Answer

Malfucnction Indiator lamp


The malfunction indicator lamp(MIL) indicates a faulty sensor/s in the ECM system management. If it is flashing it will be a code as to the fault and the faults can be read by a scanner to determine the nature of the fault. Once the fault has been fixed then a scanner can be used to reset the MIL

May 31, 2014 | Pontiac G6 Cars & Trucks

1 Answer

My malfunction indicator lamp has been on for at least 14 hours, we put in some new oil and check the gas cap this morning and put it tight but the malfunction indicator lamp is still on what else could we...


The light could mean many possible issues. You will need to get someone to read the code to determine what is the potential problem. You have numerous sensors that can set the light off,

Feb 19, 2011 | 2006 Chevrolet Cobalt

1 Answer

Malfunction indicator lamp illuminated on daewoo lacetti


The check engine light comes only when the computer control unit (called the PCM) senses a fault in the electronic controls of the engine and/or the emission system, there are about 200 possible faults that turn the light on, to know what has developed a problem you must have the system tested, this is called an OBD2 fault code test

Jun 02, 2010 | 2000 Daewoo Lanos

1 Answer

Malfunction indicator lamp in my toyota corolla is on how i fix?


The check engine light also called the malfunction indicator comes only when the computer control unit (called the PCM) senses a fault in the electronic controls of the engine and/or the emission system, there are about 200 possible faults that turn the light on, to know what has developed a problem you must have the system tested, this is called an OBD2 fault code test, Kragen and Autozone parts stores do this testing for free.

May 27, 2010 | 2002 Toyota Camry

2 Answers

I have malfunction indicator lamp on how i can fix that


Same thing...Let them scan it so you can get the code

May 27, 2009 | 2003 Honda Accord

1 Answer

Malfunction Indicator Lamp


it is safe but how long is a piece of string you really need to get to a dealership asap to determine why eml light is on

May 26, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Malfunction indicator lamp


The Malfunction Indicator Lamp or MIL (Also called the check engine light or service engine soon light) comes on when the on board computer detects an issue with the operation of the engine or transmission.

The best thing to do is to take the vehicle to an auto parts store like Autozone and have them hook up their scan tool to the vehicle and read the code. They can read it, tell you what it is and also tell you what the code means.

If it is pointing to a faulty component or sensor and you replace or repair the component the the light will go off on its own after the computer sees that the malfunction is no longer present.

You can have the code cleared, but if whatever caused the light to come on in the first place is not addressed then it will just come back on eventually.

Dec 31, 2008 | 2006 Toyota Tacoma

Not finding what you are looking for?
2003 Honda Accord Logo

Related Topics:

683 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...