Question about 1988 Toyota Cressida

1 Answer

My gear doesn't works

My autogear doesn't works properly.my mechanic also checked gear box clutch plates are fine.there isn't any problem. please solve my problem soon.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 166 Answers

You vaguely describe your problem. If not the clutches, depending on the exact problem you are having with your gear, these articles may be able to assist you on that:
http://yourhandymanzone.com/Your_Handyman_Zone_How_To_Pages_Vehicle_Car_Zone_Cars_Trucks_Vans_Transmission_System.htm

Posted on May 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why will the gears of my actros truck not workafter fitting new clutch


well a description of the problem would be a big help
does the gear crash when the clutch is pressed in
can the gears be engaged cleanly when the engine is stopped
did you install a single plate clutch or duel plate clutch
if the gears worked properly before removing the box , then the problem will be in the clutch plate fitting ( wrong way round and the hub is hitting on the flywheel bolts or duel plate on clutch bub is incorrect hitting on the other clutch hub)or the gear shifter installation after fitting the box

Sep 13, 2014 | Mercedes-Benz Mercedes Bentz Actros Semi...

1 Answer

Manual transmission re-submit


IT is possible that the transmission was damaged during clutch replacement. IF the box didn't slip home easily but was pulled into place with the flange bolts the damage would be in the clutch plate but it may have put pressure in the input shaft and bearing. The jumping out of gear is indicative of a misaligned gear box to bell housing situation Undo all the flange bolts and check that there is nothing caught between the faces of the box and housing . Re-tension going around the bell housing tightening each bolt a bit at a time . Check that the flange face and the bell housing are together all the way round.5 th gear is in effect outside the gear box proper and is inside the extension housing and is remote from the problem if the box is properly aligned . If misaligned then the wobble in the input shaft will wobble the output shaft which will work the 5th gear out of mesh

Feb 23, 2014 | Kia Cars & Trucks

1 Answer

Manual trans won,t shift 87f150


When there is an issue with a manual gear box not working after a clutch replacement I am always suspicious that the clutch plate has been fitted the wrong way and the crank bolts are fowling on the cluch plate center . If the gear box was fine before and i now faulty I would go to what was done with the clutch. Also check that the clutck slave cylinder is working ok.

Feb 22, 2013 | 1987 Ford F 150

1 Answer

Car shakes when i take off its a 960 volvo


do you mean that on the attempt to move first gear? if is that probably you will have a clutch problem.Either is you clutch disc broken springs,your pressure plate doesn't release the disc properly,or your hydraulic clutch system -if it is hydraulic- doesn't work properly.

Sep 04, 2012 | Cars & Trucks

1 Answer

94 toyta pickup chage starting hard shifting gear replace slay slender not solve -change clutch not slove problem change clutch hyd master cylender not sloved broblem some one say chage transmission- what...


If you're sure that the clutch hydraulics are working properly ... then you are going to need to pull the transmission to see why the release isn't working .... bad throw out bearing, problem with pressure plate or ??

Trouble shooting here:
http://www.ncttora.com/fsm/1993/clutch/1troubles.pdf

Aug 21, 2011 | 1994 Toyota Pickup

1 Answer

First gear selection problem.Sometimes goes in easy but sometimes not at all until I pump the clutch a couple of times.Mechanic says its not hydrolic fault but believes it to be a syncromesh problem,What...


Not a transmission problem. Sounds like the clutch isn't disengaging which could be caused by anything from a bad slave or master cylinder to a bad pressure plate release mechanism. First make sure that the reservoir is full of fluid, if not check for leaks. Then I would try to bleed the system at the slave cylinder. If the slave cylinder piston is moving properly but the clutch doesn't disengage you have a bad pressure plate.

Jul 02, 2011 | Kia Sedona Cars & Trucks

1 Answer

I am having a gear shifting problem with my Kia Sportage (4x4 Gasoline engine, 2009 version). taking off from an incline drive it is difficult to shift from first to second gear (grinding noise). Also...


Check your clutch fluid box located by your breaks master cylinder. Your clutch works like your breaks in that when you press the clutch pedal it uses hydraulics to disengage your clutch plate. If it's low or not working properly your clutch plate won't fully disengage and could lead to more problems.

May 27, 2011 | 2000 Kia Sportage

1 Answer

Peugeot 206 NEW clutch pressure and clutch plates were replaced including the bearing. Clutch is making a rattling noise but not when pedal is down. Having difficulty getting into 1st and 2nd gears....


its likley to be the clutch center plate cush springs are loos and the center plate is warped so wnen you try to get into gear the clutch is draging the gear box around,,,bipping the clutch stops the clutch spinning so no noise! all you can do is strip the lot down again and fine the fault and fix it

Feb 08, 2010 | 1987 Peugeot Liberte

1 Answer

Have a mazda 323 2001 astina it is a manual gear box when driving a long the car starts to kangaroo hop in 1st gear, 2nd gear and 3rd gear 4th and 5th gear are fine can you tell me if this is a gear box...


Sounds like oil on the clutch plate lining, burned or glazed facings. Could be worn or loose engine or transmission mounts. Sometimes it is worn splines on clutch plat hub or a warped pressure plate or flywheel.

Sep 14, 2009 | Mazda 323 Cars & Trucks

1 Answer

Sound in gear box when shiftting gear (Manual Trans)


it maybe can be clutch plate also clutch bearing.
It can be also in side the gearbox front main shaft when the bearing is worn out it makes noise.

Jun 10, 2008 | 1986 Toyota Corolla 2 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...