Question about 1990 Ford Bronco

1 Answer

1990 ford bronco cuts off after it warms up

It getting gas fine but it will cut off on the freeway or street i sit still for maybe 2 to 10 minutes and it will start again!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,036 Answers

Sound like ignition module problems.it act up when engine is warmed up.

Posted on May 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where to cut ecces hole f0r fuelpump replacement


Not a good idea to do this. If you cut threw a fuel line while cutting the floor, You will catch the vehicle on fire. This would be very difficult to put out, because the fire would be between the floor and gas tank.

Apr 15, 2016 | 1990 Ford Bronco

2 Answers

Rough Idle when starting when motor is warmed up


My brother has a Ford F150 that does this the problem turned out to be a bad mass air sensor (little black box with plug in on it located next to the air box on the air intake pipe

Jan 29, 2014 | Ford Bronco Cars & Trucks

1 Answer

I have a 1995 Bronco with the 5.8, starts and runs great when cold, but when its warmed up and I turn it off and let it sit for 10 minutes and try to start it sputters, idles rough and sometimes dies. If...


No codes will show but one of the mechanics would have known whats wrong so try another dealer ,i suspect a temperature sensor is giving the wrong information to the computer but as i have never seen one of these vehicles i couldnt tell you what and where sorry about negative answer but ?? now a citreon or a renault i can answer

Jan 29, 2014 | Ford Bronco Cars & Trucks

1 Answer

Engine cut out


Has anyone checked fuel pressure cold and hot ? Check engine light on ?

Sep 26, 2013 | Chevrolet Lumina Cars & Trucks

1 Answer

My 83 Ford Bronco keeps cutting off at every stop. it puffs like it's fighting to stay on before it go's out please help.


Sounds like your Carb needs to be tuned. If that doesn't do it rebuild or Buy a new one.

When I get in my Chevy First start of the day I press the gas pedal to the Floor 2 times and then hit the key to start it and it starts right up at a fast idle then you have to manually kick it down to a lower idle by putting it to the floor and letting off real fast kicking it to a normal running idle.
It could benefit you to let it warm up a bit longer also. I have to give my chevy 5-10 minutes before I drive off in it..


Might try and run some fuel stabilizer through it. Stuff that will remove water and other things that will make your motor run worse (maybe run a better grade of fuel in it).


When was the last time you replaced the Spark plugs? That could also benefit you. Just the general tune up things could make a world of difference.


Also if it does this when the motor is fully warmed up you might turn up your idle as that could be a problem. Let me know what works for you.

Mar 24, 2013 | 1983 Ford Bronco

1 Answer

Ford Focus cutting out


Here is the most common cause of surges and stalls, it is the idle speed control air-bypass valve and throttle valve, they get full of gunk over the miles and cause idle issues (stalls) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

Dec 03, 2008 | 2000 Ford Focus

1 Answer

Ford Freestar--engine cutting out


I'd like to come into contact with to purchase your vehicle

Nov 18, 2008 | 1990 Suzuki Swift

3 Answers

Need 2 get truck started


I had a geo metro that sat a long time and the gas turned to varnish. You will need to drop the tank, clean out the gunk, put in a new fuel pump and and filter and flush the fuel lines out to the injectors.

Sep 05, 2008 | 1990 Ford Bronco II

Not finding what you are looking for?
1990 Ford Bronco Logo

Related Topics:

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...