Question about 1999 Ford F150 Regular Cab

2 Answers

1999 f150 2wd transmission clunk

When I put it into gear reverse or drive it shifts easily but there is a loud clunk, would it be the ujoints or rearend going out.
It is an automatic transmission and shifts nicely while driving though.

Posted by on

  • andrew08 May 26, 2009

    motor1258, no, there is no squeek or vibration while driving.

  • Mike Butler
    Mike Butler May 11, 2010

    Any squeek or vibration when driving?

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,674 Answers

You can usually tell by grabbing the driveshaft & turning it by hand back & forth & push up & down, side to side looking for play in the joint.

Posted on May 26, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Ujoints I would check out first mainly the rear one. if it wobbles in the sockets its worn

Posted on May 24, 2009

  • frank thomas wilson
    frank thomas wilson May 26, 2009

    You will only hear it when shifting out of park and when you slow down to brake at the early stages of wear in the u joints. After a few thousand miles it will break off more than likely

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 Toyota Land Cruiser, It will not move in drive or reverse, it's making a loud sound, and appears to be locked in gear when you mash the gas. Do you think the transmission is gone? or


Take a loom at the manual gear shift. Not the auto one. I mean the 4wd one. I think you will find it is not where it should be. Push it back into place.

Jan 29, 2013 | 1999 Toyota Land Cruiser

3 Answers

When put my automatic 2001 Saturn SL1 into reverse it makes a Loud clunk noise before it reverses also it clunks before accelerating into the next gears..? why?


2001 Saturn SL1. Transmission (automatic) shifts hard when putting it in gear and every gear there after. The only codes I get is PO442 and PO410. Any help would be greatly appreciated.

Jul 08, 2010 | 1999 Saturn SL

1 Answer

2005 Corolla's manual trasmission shifts gears, it clunks


hi mate , sounds like the SPIGOT bearing its a little bearing that allows the gearbox to be at a different seed than the engine flywheel and if this is in bad condition it will take the gearbox front shaft to a higher speed than comfortable for gearshift , in the meantime when you go for 1st or reverse gear just engage a gear like 4th without taking your foot off the clutch and then go for 1st or reverse, this will stop the gearbox spining long enough for a smooth shif, oNLY USE THIS METHOD WHILE STaTIONARY and see a professional when you get time.

Mar 29, 2010 | 2005 Toyota Corolla

1 Answer

Transmission leaks, clunks into gear


Well your clunking noise is most likely the u-joints the leaking pan is the tranny pan what you would have to do is get a tranny kit and change the pan gasket tranny filter and fluid or take to a shop and have a tranny service done.

Sep 02, 2009 | 1999 Chevrolet Blazer

1 Answer

No reverse and shifts hard if forward gears


best bet is call scrap yard they are fairly decent priced unless you want new

Aug 25, 2009 | 1996 GMC Jimmy

2 Answers

Tranny clunks when shifting gears


Check motor and transmission mounts.

Jun 15, 2009 | 1999 Buick Park Avenue

1 Answer

2004 Jeep Wrangler - Clunking Noise when shifting out of Park


It could be lash in the differential which is normal, but it could also be a loose u-joint in the driveshaft. Check the rear driveshaft u-joints.

Mar 12, 2009 | 2004 Jeep Wrangler

1 Answer

I get a very loud clunk when I put the transmission into drive or reverse. I remove my foot from the accelerator to allow the transmission to go to the next gear otherwise it goes above 3,000 rpm to...


Try replacing your fluid filter in your transmission first. If that does not work, your tranny could have the gears wearing out. To solve the shifting problem, have a shift kit put in your transmission.

Jul 30, 2008 | 1990 Toyota Camry

Not finding what you are looking for?
1999 Ford F150 Regular Cab Logo

527 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...