Question about 2006 Kia Sorento

1 Answer

Need to replace bearing on sedona but cant get axel out of bearing hub

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Try this website to see if they have your listed if they do you be able to get pictures and diagrams as well www.autozone.com and another one to try is www.alldatadiy.com for more repair information.

Posted on May 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there something more to removing the front hubs of a 09' focus then just pushing the axel out of the bearing?


The 3 or 4 bolts at the back side of the steering knuckle
it is bolted to

Have to loosen the bottom ball joint I believe in order to get the axle out

Mar 07, 2013 | 2009 Ford Focus

1 Answer

Removing half axel pass side kia sedona 02


Hi Kieth, Yep you just pry them out with a flat large blade (don't use anything sharp and watch out where you put your legs. Remember you have arteries which need protecting. Cussing and swearing loudly helps the work too, especially if you hit a nail on your fingers or thumb. Regards John

Jul 01, 2012 | 2002 Kia Sedona

1 Answer

How to remove knuckle / hub from front axle? Splines are binding, I've applied a puller, ball and tie rod ends removed and strut to knuckle bolts are loosened. I need to replace the outer CV joint. Any...


most likely the bearings in the hub are rusted to the axel. If you work at it you can use a point air chisel to push the axel shaft out you will have to replace the bearing in the hub. worst case you could take the hub and axel off together and press the axel out in a press. either way you will have to replace the hub bearing.

Mar 20, 2011 | 2000 Kia Sephia

3 Answers

How to replace a front wheel hub assembly on a 1999 blazer 2wd


remove tire
remove axle nut
remove 3 bolts holding hub in
sometimes may need to hit hub with hammer after all bolts out to get it to release

Dec 22, 2010 | 1999 Chevrolet Blazer

1 Answer

Rear wheel bearing


if its like the 99 winstar:

safely support the van, remove rear wheel, remove brake drum, remove grease cap. remove caged locknut assembly (38mm socket i think.) then pull the hub assembly from the axel. you may need to cut away the inner race if the bearing falls apart. clean axel, apply alittle anti size compound, then push on the new hub assembly. tighten down the hub nut to specifications (should be on the leaflet in the new bearing package), install dust cap, install drum, install wheel, lower and drive :)

May 25, 2010 | 1998 Ford Windstar

2 Answers

2004 Kias Sedona. I have the replaced the Front Wheel Bearing (Passenger Side) 4 Times in the last 6 months. The last one lasted 2 Days. It was sluggish going uphill, jerking, and then there was a loud...


My guess is the original shim that came with the factory bearing and hub assembly was discarded and never installed on the new bearing (That does not come with a shim) causing the new bearing to fail.

Jan 16, 2010 | 2004 Kia Sedona

1 Answer

I replaced hub on front axel but the noise is


It sounds like it is a front end suspension problem. The following should be checked: upper and lower ball joints, the sway bars links, and even the shocks. Replace what is problematic, and your front-end noise should disappear, if it is a front suspension problem. Hopefully, this will FixYa problem!

Jan 04, 2010 | 2001 Ford Excursion

1 Answer

How do I go about changing the bearings in my front hub?


In order to change them you must do the following.
1) Remove tire
2) decompress the brake caliper
3) unbolt brake caliper and lay it to the side (no need to disconnect brake line
4) remove castle nut from axel
5) unbolt stearing linkage from ball joint (on van door side of hub)
6) unbolt strut from hub (make sure the vehicle is jacked up high enough to allow the hub/wheel assymbly to hang as low as possible.
7) remove CV axel from hub
8) unbolt lower ball joint from hub
9) take hub out
10) remove seal and retainer ring form front and back of hub (retainer ring is on the front side seal is on the back side
11) I highly recommend a press (rent one it is worth it, trust me) and remove the old bearing.
12) insert new bearing and press in (again I recomend renting the press)
13) put everything back the way it came off and your done.
NOTE: I strongly suggest placing the bearing in the freezer for several hours before you start working on the replacement. This lets the metal contract slightly and makes it easier to get it into the hub.
Also you might need a small propain torch to heat the hub up to make it easier to remove the old bearing (especialy if you do not have a press, again RENT THE PRESS)
Good luck.

Oct 18, 2009 | 2003 Kia Sedona

1 Answer

Can't get the bearing hub out to replace the bearing


You'll need to remove the 2 strut bolts holding the hub to the strut, remove the axle nut. Pull the hub towards you and try taping on the axleshaft to try to push it out. You might try spraying some WD-40 where the axleshaft goes thru the hub.

May 24, 2009 | 2006 Kia Sorento

Not finding what you are looking for?
2006 Kia Sorento Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...