Question about 1998 Jeep Grand Cherokee

1 Answer

I cant figure out how to change the driver's side headlight

I cant find what screws and stuff i need to use to change the headligt assembly, which has water in it, on my 98 jeep grand cherokee

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

You have two screws at the top of the trim cover. remove them and tilt top towards you and remove from slots at bottom.
There are four screws holding the ring around the lamp. spray them with solvent and remove them the rest is just unplug and plug back in don't put it back upside down. (use a really good new screwdriver and if screws on ring won't come out after soaking tap the back of the screwdriver with a hammer to break rust in threads)

Posted on May 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace low beam drivers side headlight on 1993 olds cutlass supreme convertible


Remove turn signal assembly (uses a torx 15 driver). This will expose the two 10mm bolts on the one side of the headlight assembly. Remove the plastic front grill (uses a torx 15 driver - there are about 6 screws). This will expose the other two 10mm bolts on the headlight assembly. Remove the four 10mm bolts to remove the headlight assembly and this will allow you access to the headlight you need to replace.

Feb 18, 2011 | 1993 Oldsmobile Cutlass Supreme

2 Answers

How do you replace the front turn signal on a 2005 Buick Terraza?


Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

Sep 07, 2010 | 2005 Buick Terraza

2 Answers

Need to change one of the daytime running light bulbs. Cant see how to get to it.


You will need to take the tire off of the side that the light is burned out on. Then remove plastic fender well insert. This will give you the enough room to change out any burned out light in the headlamp assembly.

Jul 10, 2010 | 2007 GMC Acadia SLE

1 Answer

How to change headligt bulb in 1999 vw bettle


ahhh... the ultimae "bug" kwirk. heres how it goes

Theres a lever on the side of the housing you must turn. but to turn it you have to push the lock in. then the entire headlight housing will slid out the front of the car. Then unplug the wiring and remove the plactic backing. replace the headlight and re-assemble your bug :)

Nov 12, 2009 | 1999 Volkswagen Beetle

1 Answer

Remove driver side headlight assy to replace side marker light


There are two screws holding the headlight in. The screws are just above the headlight. After removing the screws you'll need to carefully pull straight out on the headlight assembly. There's a ball/socket type joint just behind the headlight. This joint needs separated for the assembly to come all the way ouit. Reaching and replacing the side light bulb requires a bit of arm twisting.
Reverse the order to re-install the headlight.

Sep 26, 2009 | 2002 Buick LeSabre

1 Answer

1999 Toyota Camry - Healight Assembly Removal


you need to remove the side light as there may be a screw holding the assembly down.

Aug 07, 2009 | 1999 Toyota Camry

1 Answer

I can't find directions on line to change the driver's side headlight out of the headlight assembly. I took the assembly out of the car, not a simple task, you have to remove the bumper, but I can't figure...


If I can remember, there should be two small screws on the bottom left of the headlight. This is the spring load. remove the screws and also remove the two small screws on the upper right. this will help remove the adjusting screw. the installation is in reverse.

Jun 28, 2009 | 1990 Honda Accord

1 Answer

I cant remove headlight from 1993 ford taurus.


Very easy, remove the orange turn signal light assembly. After that, unscrew the 2 screws that hold the headlight assmbly in place.

Then you remove the 3 screws that are holding the head light assembly in position....that's it.

Mar 19, 2009 | 1993 Ford Taurus

1 Answer

Headlights not working


BAD HEADLIGT SWITH BAD RELAY ON MOTOR COMPARTEMENT DRIVER SIDE OVER THE WHEEEL

Mar 18, 2009 | 1994 Chevrolet Caprice Classic

1 Answer

How do you change the drivers side headlight assembly?


You need to remove the bumper assembly to remove the headlight.

Oct 14, 2008 | 2003 Nissan Altima

Not finding what you are looking for?
1998 Jeep Grand Cherokee Logo

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...