Question about 2000 Oldsmobile Alero

1 Answer

The turn on lights does not flash

Oldsmobile alero 2000 turn light problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Oldsmobile Master
  • 3,854 Answers

Check out this recall below:
Bulletin No.: 04098A

SPECIAL POLICY
Subject:
04098 - Special Policy Adjustment - Turn Signal/Hazard Warning Flashers 

Condition
Some customers of 1999-2002 Chevrolet Malibu, Oldsmobile Alero, Pontiac Grand Am, and 1999 Oldsmobile Cutlass may have turn signal/hazard flashers that become inoperative.

Special Policy Adjustment
This special policy covers the condition described above for a period of 10 years or 150,000 miles (240,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. The repairs will be made at no charge to the customer.

Good luck and hope this helps:
HAZARD WARNING SWITCH REPLACEMENT - ON VEHICLE 
REMOVAL PROCEDURE 

Remove the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent. 
Remove the instrument panel cluster. 
Remove the hazard warning switch bezel from the instrument panel using a small-flat bladed tool to release the retainers.
Remove the left side bolt from the hazard warning switch through the instrument panel cluster pocket Remove the right side and center lower bolts from the hazard warning switch through the center air louver deflector pocket.
Reposition the hazard warning switch from the instrument panel to access the electrical connector. 
Disconnect the electrical connectors from the hazard warning switch. 
Remove the hazard warning switch from instrument panel. 

INSTALLATION PROCEDURE
Connect the electrical connectors to the hazard warning switch.
Position the hazard warning switch to the mounting points in the instrument panel. NOTE: Refer to Fastener Notice in Service Precautions.
Install the left side bolt to the hazard warning switch through the instrument panel cluster pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the right side and center lower bolts to the hazard warning switch through the center air louver deflector pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the hazard warning switch bezel to the instrument panel pressing into place until fully seated. Install the instrument panel cluster. 
Install the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent.

Posted on May 24, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2001 oldsmobile alero

If the "check engine" or "service engine soon" light is flashing, it could be the engine is miss firing. This could be caused by a bad spark plug wire or spark plug. How old are they? After changing the plugs on my 2001 Olds Alero (at 125k miles) I noticed the engine occasionally miss fired and the "service engine soon" light started blinking. I used a timing light to determine which cylinder was miss firing and changed that spark plug wire. Advise would be to change the whole ignition wire set, but I was cheap and just changed the one wire, which cost $23 from a GM dealer. That was 14 months ago and the car runs great.

Posted on Nov 22, 2008

  • 10 Answers

SOURCE: 2000 alero flashing dash lights

you are going to have to take the dash apart. You probably have a short in the connector where it comes into the gauge cluster

Posted on Jan 25, 2009

  • 123 Answers

SOURCE: I have a 2000 Oldsmobile alero and the cruise

there might be a problem with your brake system. If there is it wont allow the cruise to work. Hope this helps alittle

Posted on Feb 07, 2010

MECP Guy
  • 344 Answers

SOURCE: How do you bypass the security system on an

do you have an aftermarket alarm in this car

Posted on Mar 06, 2010

emissionwiz
  • 76649 Answers

SOURCE: i had the oil changed but the change oil light is

How to Reset the Change Oil Light

After changing the engine oil, the system must be reset.

With the ignition key to ON, push the RESET button

located in the driver's side instrument panel fuse block. The

CHANGE OIL light will start to flash, press and hold the

RESET button again. The reset is complete when you hear
the chimes sound and the CHANGE OIL light goes out.

Posted on Oct 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to reset anti-theft on a 2000 alero


The security, antitheft or lock picture/icon is a visual indication that something in the car's antitheft system is failing. In most GM cars and trucks there is a hidden system that most people are unaware even exists. From the moment you put your key in the ignition, there begins a constant line of communication between your key's security chip or transponder, to the ignition's lock cylinder, and then to the car's TDM (Theft Deterrent Module). These 3 parts are in CONSTANT communication. If the key is in the ignition, then these parts are sending signals to each other. The security light illuminates when that signal gets broken, even just for a second. When the signal breaks, the car misinterprets this as an attempt at theft and goes into antitheft mode. The car thinks its being stolen or hotwired because it is not getting that signal from YOUR specific key. This is why the security light turns on and shuts down your vehicle. This link explains it pretty well.
http://www.diy-gm-security.com/

25627937-vycpj41x2iphfdmbx4v0vfed-3-0.jpg

Apr 04, 2015 | 2000 Oldsmobile Alero

1 Answer

I got an alero 2000 how do reset for checkengine and change oil lights??


On the drivers side there is a fuse panel, you will need to remove the cover and there you will see a reset button. Turn the ignition switch to on and then press the button, the light will flash, then press and hold the reset button until the light goes off, this will also work for the TPS system. Hope that helps

Jan 13, 2011 | 2000 Oldsmobile Alero

3 Answers

I had the oil changed but the change oil light is still on, how do i reset the computer? 2000 oldsmobile alero


How to Reset the Change Oil Light

After changing the engine oil, the system must be reset.

With the ignition key to ON, push the RESET button

located in the driver's side instrument panel fuse block. The

CHANGE OIL light will start to flash, press and hold the

RESET button again. The reset is complete when you hear
the chimes sound and the CHANGE OIL light goes out.

Oct 25, 2010 | 2000 Oldsmobile Alero

1 Answer

My 2000 alero won't start. Everything turns on otherwise, power locks work, radio, etc. A jump didn't do anything for it.


may have a stater problem,,,or anti theft,,is the security light flashing,? or ignition switch,,

Apr 28, 2010 | 2000 Oldsmobile Alero

2 Answers

I HAD MY OIL CHANGED ON MY 2000 OLDSMOBILE ALERO,


in the control panel one the right side of the car there is a reset button. all you have to do is turn the car to when all the lights are flashing and hold the reset button until the car dings.

Apr 15, 2010 | 2000 Oldsmobile Alero

1 Answer

Oldsmobile 2000 Alero side brake lights don't work, center does


does this car have a trailer hitch? if so, check the hitch wires for damage or a short

Jan 11, 2010 | 2000 Oldsmobile Alero

1 Answer

2000 alero flashing dash lights


you are going to have to take the dash apart. You probably have a short in the connector where it comes into the gauge cluster

Jan 16, 2009 | 2000 Oldsmobile Alero

3 Answers

2000 ALERO SECURITY LIGHT


When the vehicles security light is flashing and the car won't start..put the key in the ON position and wait until the security light stops flashing and then turn OFF and then start. this is from a security glitch and it shuts down the gas so car won't start. Good luck!!

Nov 05, 2008 | 2003 Oldsmobile Alero

Not finding what you are looking for?
2000 Oldsmobile Alero Logo

939 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...