Question about 1991 Ford F150

1 Answer

Wiring from sylenoid switch out to engine

Wiring from sylenoid out to engine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Solenoid wires start at the ignition switch to the solenoid

Posted on May 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 Ford taurus starts when its cold then once it gets warm and you shut it off it wont start until it cools off again


Did you replace the ignition distributor stator? they are the real problem not the TFI ignition module. See part below. You must remove the distributor to replace this part, it would also be a good idea to run a fault code test on the EEC 4 engine control system.
4p1258-mvo5utiinxaozxzewv5notdb-4-0.jpg

Apr 20, 2017 | Ford Cars & Trucks

4 Answers

Turn key get nothing jump starter and sylenoid just spins


i cant dope out that symptoms.

does it crank or not. be clear there.

no car starts (but my 6sp) if it dont crank.

on A/T cars cranking is a first thing. so does it.?

Solenoids do not spin, the stroke only , it a linear motion.

the Sol. moves the pinion and the main contactor switch only.



my guess is the Starter spins and the crank don\'t spin,

you hear the starter motor spin up, it sings. like bird.

that means the starter /solenoid are bad. (crude)

if the battery is good and or jumper starting off a running car.



It can just be a dirty starter pinion, clean it , repeat.

fixed many for this. i have.



battery cable lugs clean, and good. no green rust.

bad cable usually just make a loud THUNK sound. no spin.

Sep 02, 2014 | 2005 Jeep Wrangler X

1 Answer

I havea ingersol rand lull vr90b with a perkins diesel engine i took the starter off to have it worked on acted like the sylenoid was bad it would kick in two or three times before it would crank but...


The stop solenoid will only work when you have power applied. That way when you switch of the engine the solenoid pushes forward and shuts off the fuel. In short any power failure switches off the diesel. So wire it so wih power it is sucked in

Jan 10, 2014 | 1996 Ford F350 Crew Cab

2 Answers

Replacing gear shift sylenoid


The mechanic thinks that changing parts at your expense will make the problem(s) go away. In reality, discovery of "bad wiring" is part of the probable cause analysis that should precede parts replacement.

Dec 21, 2013 | 2003 Kia Optima

1 Answer

Santa fe 2007 wont start makes a single click noise


May be ab bad starter solenoid, or corroded/loose connection at starter, or (ground). Could also be a bad ignition switch. Start from the load; the starter. Test for 12V at starter, OK. Connect short wire from starter and touch sylenoid connection..

Nov 09, 2013 | 2003 Hyundai Santa Fe

1 Answer

My 1998 mazda 4cyl at times will not connect the starter action, have replaced the starter,sylenoid,ignition switch,everything is ON guages etc. but ignition only works off and . Then you rock the car or...


It could be as simple as a poor connection on the starter solenoid wire. Is it a push-on connector? One could do a little checking. When the starter won't work, test for power on the solenoid wire when key is held in crank. If power there, clean the connector, and check if starter works. No power? Then move to the neutral safety switch, check for power leaving the switch, key in crank, and clutch depressed. Power should be passing through the switch.
Another thing to check is all your grounds-the battery, the engine ground, computer harness ground.

Jan 04, 2013 | Cars & Trucks

1 Answer

Replaced coil, distributor module, sylenoid on fender pickup in distributor all relays and truck will not crank power going to coil no fire coming out though


are you sure the distrubitor is turning? you might have lost a timing chain. if you need it i have the wiring diagram for the truck just let me know what engine and transmission. and give me your e-mail to send it to.

Jun 22, 2011 | 1991 Ford F150

1 Answer

Transmission Problem


band adjustment goes like this, Break the jamb nut loose and back it off a couple of turns then torque the center stud to 10 ft pounds then back it off 2 turns and tighten the jamb nut.
Jim

Oct 04, 2008 | 1994 Ford Explorer Limited

Not finding what you are looking for?
1991 Ford F150 Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...