Question about 1995 Toyota Previa

1 Answer

Banging from the front prop shaft

Banging from the front prop

Posted by on

  • dannyls11aut May 24, 2009

    dont mean to bother u but i dont suppose u have a picture or a diagram off how they come apart the bearings i bought from the dealers. in a rush i toke them off with out marking them every time i put them together and start the van it sounds like it knocking its nuts off

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Bearing bad or bearing housing egged out

Posted on May 24, 2009

  • frank thomas wilson
    frank thomas wilson May 24, 2009

    no I don't. Check to see if the housing was out of round from wear. if you did install the new ones yourself did you press these in or hammered then in?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the prop shaft located?


Your vehicle doesn't have a PROP shaft. Yours has a drive shaft. Prop shafts are normally on 4x4 trucks and refer to front drive shaft. What trouble are you having with the cruise control?

Aug 02, 2015 | 2004 Buick LeSabre

1 Answer

How to replace front joint at diff. on quadra- trac 4x4?


is this as spindle
or the front prop shaft.
why not read all steps in the FSM for this car.
posted like 200 times now, ever search?

jeep, zj, post 201

click diffs here.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

2nd page shows prop shafts.
RTM
then ask questions not clear there.
or at alldata.com
or at real FSM page here.

https://www.techauthority.com/en-US/Pages/Home.aspx


FSM means real OEM factory service manual.

Mar 27, 2015 | 1995 Jeep Grand Cherokee

1 Answer

How fix drive shaft loose jeep cherokee?


which one, there are 8. (total prop shafts and axles)
my wild guess is front of car.
guess, 2, is ujoints loose.
but there are many there.
the front prop shaft u-joints, and the front axle end U-joints.

why not post a photo with finger pointine to IT.

Mar 09, 2015 | Jeep Cars & Trucks

1 Answer

How do i remove drive shaft from jeep liberly


the rear shaft? center prop shaft.
front, rear or CV? what? try point to the shaft and say
IM here, at X and want to replace Z, exactly HERE.
I toss dice land on REAR.
the joints have bolts, see them>? did you even look or just wondering?


which engine,
which transmission and 4wd options, called drive line, we can not guess this....
there are 8 , driveline optios (i cant guess it)
and 3 liberty models, ill guess sport
but will.
here is my wild guess.
http://www.factorychryslerparts.com/showAssembly.aspx?ukey_assembly=566769&ukey_make=1064&ukey_model=15531&modelYear=2003&ukey_category=20306&ukey_driveLine=7453&ukey_trimLevel=18760

see those rear bolts at the rear U-joint>?
1: match mark those rear parts, (means mark them so you get them back right , they are factory balanced..
2: remove the 4 bolts and nuts.
3: the prop shaft drops.
4: have a pan below, the A/T tranny (wild guess that) and catch any
ATF fluid that drips here.
5: slide the prop shaft of end of tranny or xfr case as it may apply.

or read the FSM,
or login to alldata.com and read. like we do.

Sep 10, 2014 | 2003 Jeep Liberty

1 Answer

1999 grand vitara 4wd how do front hubs disengage


best why is one tire on ground, front.! spin other tire. and feel prop by hand... fell the energy there. (there is no other way)
did you try to stop the prop shaft (xfr to axle) by and, while turning
tires? that is the test, free air spins only invite, fails reading due to
the viscous nature of GL5 lube.

the front axles has a 4wd drive has an internal pneumatic
air slave servo. and and external pump.
disconnect the air hose there. at pump to axle.
if axles is still locked up the internal slave is bad.


4ecbf43a-d636-43ce-a6df-a0889a3cf399.jpg


NOISE, is one of the most hardest problems to find in any machine
and for sure cars that only make noise moving, 100x harder
no body here can guess this, we are deaf here but I can tell you
most noises are:
1: bad u-joint.s
2: tires bouncing. (unbalances, did the silly glue on weights fall off?)
3: bad wheel bearing. (feel them, if you can feel play its bad)

use an electronic, stethoscope and end the danger, moving.

http://www.fixkick.com/NOISE.html


best bang for buck is here, buy cheap walfart head phone muffs for $5 for best play.

http://www.amazon.com/Steelman-97220-EngineEAR-Diagnostic-Listening/dp/B00396FBRY/ref=sr_1_10?ie=UTF8&qid=1410351389&sr=8-10&keywords=steelman+stethoscope

Sep 09, 2014 | 1999 Suzuki Grand Vitara

3 Answers

Drive shaft knocks


check your universal joints first if not may have bad bearring

Aug 19, 2012 | 2006 Kia Sorento

1 Answer

Front Prop shaft bearing on freelander needs replacing again. Why?


Prop shafts are actually balanced, if the balance weight has fallen off it will keep damaging the bearing, check for a balance weight, it is like a flat piece of metal stuck to the prop, there may be more than one.

May 22, 2012 | 2005 Land Rover Freelander

1 Answer

The clearance between the propeller shaft and the gear box of cortina 16E (1970) thanks


You have me confused? There is no clearance between the prop-shaft and the gearbox. THe front of the prop-shaft slides over the splines on the end of the gearbox and the end of the shaft bolts onto the flange on the differential which locates the prop-shaft longitudinally, with a bit of sliding movement allowed on the splines for suspension and engine movement. Come back to me if that is not what you were asking.

Mar 03, 2011 | Ford Escort Cars & Trucks

1 Answer

Is it easy to replace a prop shaft uj or do you need a special tool ? can any one help please


answer,yes,the prop shaft has about 10/12 bolts remove and re fit,[]tip] get a marker and mark the position inline with the old one ie run the line back and front.adrian,,,,,

Jun 28, 2010 | Daihatsu Rocky Cars & Trucks

Not finding what you are looking for?
1995 Toyota Previa Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...