Question about 1993 Chevrolet Lumina

1 Answer

What two coolant lines connect to the throttle body on a 3.1 multi port engine

What two coolant lines hook up to the throttle body on a chevy lumina 3.1 multi port ingine

Posted by on

  • daler_49 May 24, 2009

    There are two coolant connections at the bottom of the throttle body. In fact the manual tells you to drain all the coolant prior to diconnecting the coolant lines on the throttle body. My problem is somebody else had disconnectedall the hoses and cut them off.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

There are no coolant lines connected to the throttle body, just the two fuel line. The high pressure side and low pressure side (Return line) and I believe the lines don't even connect to the throttle body on a multi port engine, the lines go to the fuel rails to the injectors.
Good luck

Posted on May 24, 2009

  • Harvey N Tawatao
    Harvey N Tawatao May 24, 2009

    There heater lines off a steel water pipe from the water pump which runs along the Valve cover. There should be two fittings off the black metal pipe, use a rubber from the throttle body to the heater pipe. The rubber hose is a rubber fuel line, so if your going to have to pick one up, that's what you use. 


    Good luck 

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Where is the freeze plug located on a 1999 Chevy Lumina 3.1L


On the block ( the bottom part of the motor ) below the intake manifold

Jan 27, 2015 | 1999 Chevrolet Lumina

1 Answer

1999 chevy lumina rough idea after warm up


It could be several different things causing this, my first guess would be to look at the EGR port going into the intake. Most times it will clog up and can cause rough idling. You must know how to clean it properly, the EGR valve will have to be pulled as well as the throttle body in order to clean it properly. Also, check for vacuum leaks. It could be other things as well but this is where I would start. Hope this helps. Thanks, Allen with Morgan's Auto Repair 912-282-1602 Waycross, Ga.

Mar 12, 2014 | 1999 Chevrolet Lumina

1 Answer

1993 chevy lumina-tps


"TPS" stands for Throttle Position Sensor. It is located in the same place that all TPS sensors are located - on the throttle body.

Apr 14, 2012 | 1993 Chevrolet Lumina APV

1 Answer

I need a vacuum line diagram fo a 1996 Chevy Lumina, 3.1. One line that is not connected to anything, is located at the top of the engine.


Sorry I don't have the diagram, but I do have a diagram of the engine and component locations. Your vacuum system is fairly simple. You have a MAP sensor attached to the air cleaner. I have pasted a picture below. It has one electrical connector and one vacuum hose that goes to the intake manifold or the throttle body.
Behind the right headlight is your evap canister. This will have a hose or line running to the fuel tank. Then it will have another hose going to the purge valve. The purge valve should be close by and it has a connector plus another hose that goes to the intake manifold.
Then you have the PCV hose that goes from the PCV valve in the valve cover to the air cleaner or intake manifold. I think yours just has a hose from the air cleaner and the rest is internal.
There is one more vacuum hose, and that is the bog one that goes from the intake manifold (or throttle body--looks to me like there are a couple of vacuum ports on the back side of the throttle body, and there may be a "T" on one of the hoses) to the brake booster. It this one was off, the engine would not run, as the vacuum draw is large. Please let me know if you cannot figure it out from these instructions and provide a picture, if you can.

MAP sensor:
jturcotte_653.jpg

purge valve:
jturcotte_654.jpg

jturcotte_2455.gif
jturcotte_2456.gif

Oct 30, 2011 | 1996 Chevrolet Lumina Mini

1 Answer

When i turn on heater or fan engine revs over 3000 rpm


Idle Air Control Valve Pintle may be bad If you disconnect the IAC and the problem ceases it can point to this being the problem.: Removal & Installation 3.5L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the fuel injector sight shield.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • The air cleaner intake duct. Figure of IAC and TPS electrical connectors disconnected. aurora_g1.gif

    • The idle air control (IAC) valve and throttle position (TP) sensor electrical connectors. Figure of cruise control and throttle control cables removed from throttle lever. aurora_g2.gif

    • The cruise control cable and throttle control cable from the throttle body lever.
    • The fuel pressure regulator vacuum hose, positive crankcase ventilation (PCV) hose and the throttle body vacuum port hose.
    • The throttle body coolant hoses.
    • The throttle control cable bracket, leaving the throttle and cruise cables connected.
    • The upper nut holding the throttle body to the intake manifold.
    • The throttle body assembly.
  5. Clean the gasket mating surfaces.
To Install:
  1. Install a new gasket and new studs if necessary.
  2. Install or connect the following:
    • The throttle body assembly.
    • Start the top nut by hand.
    • The throttle body coolant hoses.
    • Position the throttle control cable bracket and hand start the retaining nuts and bolt.
    • Torque the three throttle body retaining nuts to 89 in.lbs. (10 Nm). And the bracket retaining bolt to 115 in.lbs. (13 Nm).
    • The throttle body vacuum port hose, PCV valve hose and the fuel pressure regulator hose.
    • The throttle control and cruise control cables to the throttle body lever.
    • The IAC valve and TP sensor electrical connectors.
    • The air intake duct.
  3. Refill the cooling system.
  4. Install the fuel injector sight shield.
4.0L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable.
    • The Mass Air Flow (MAF) sensor electrical connector.
    • The air cleaner intake duct.
    • The PCV valve fresh air tube. Figure of cruise control cable removed from throttle cable bracket. aurora_g3.gif

    • The cruise control cable and throttle control cable from the bracket.
    • The cruise control cable and throttle control cable from throttle body lever. Figure of IAC valve and TPS connectors removed. aurora_g4.gif

    • The idle air control (IAC) valve and throttle position (TP) sensor electrical connectors. Figure of fuel lines removed from retainer on throttle cable bracket. aurora_g5.gif

    • The fuel feed and return lines from the retainer on the throttle control cable bracket.
    • The transaxle shift cable clip from the throttle control cable bracket. Figure of throttle body removed from water crossover. aurora_g6.gif

    • The throttle body from the water crossover.
To Install:
NOTE: The Mass Air Flow (MAF) sensor inlet and the outlet of the air cleaner assembly must line up when installed. Misalignment may cause MIL illumination or driveability concerns.
  1. Install or connect the following.
    • The throttle body to the water crossover. Torque the bolts to 106 in.lbs. (12 Nm).
    • The IAC valve and TP sensor electrical connectors.
    • The throttle and cruise control cables to the throttle body lever.
    • The throttle and cruise control cables to the throttle control cable bracket. The transaxle shift cable clip to the throttle control cable bracket.
    • The fuel feed and return line retainer to the throttle control cable bracket.
    • The MAF sensor electrical connector.
    • The air cleaner intake duct clamp. Torque the clamp to 27 in.lbs. (3Nm).
    • The PCV valve fresh air tube.
    • The fuel injector sight shield. Torque the nuts to 20 in.lbs. (2.3 Nm).
  2. Install the negative battery cable.
  3. Pressurize the fuel system and verify no leaks.
prev.gif next.gif

Oct 07, 2010 | 2001 Oldsmobile Alero

2 Answers

HOW DO I CHANGE THE THERMOSTAT ON A 1998 CHEVROLET LUMINA 3.1


FIRST OF ALL YOU HAVE TO DRAIN SOME COOLANT.JUST ENOUGH SO COOLANT WONT FLOW ALL OVER ENGINE.AND COOLANT TO EXPENSIVE ON THE GROUND.TO GET TO THERMOSTAT.YOU HAVE TO DISCONNECT CONNECTORS TO MAF EGR IDLE SPEED CONTROL AND IAT SENSOR.. REMOVE THROTTLE AND SHIFT CABLES FROM BRACKET.REMOVE AIR FILTER ASSEMBLY WITH MASS AIR FLOW SENSOR.REMOVE BOTTOM PORTION OF AIR FILTER HOUSING.REMOVE COOLANT HOSES FROM THROTTLE BODY.THEN REMOVE THROTTLE BODY ASSEMBLY.YOU HAVE TO DISCONNECT SMALL COOLANT HOSE TOP WATER PUMP.REMOVE SMALL BOLT THAT HOLDS METAL COOLANT LINE TO WATER PUMP.THIS LINE HAS TO BE MOVE JUST ENOUGH SO YOU CAN REMOVE THROTTLE BODY.ONCE THROTTLE BODY OUT THE WAY YOU CAN REMOVE THERMOSTAT.BESURE WHEN YOU PUT EVERYTHING BACK TOGETHER.REPLACE THROTTLE GASKET AND THE COOLANT HOSES COME OFF THROTTLE BODY BESURE TO USE OLD COOLANT HOSES MEASUREMENTS FOR NEW HOSES MEASUREMENTS MAKE SURE YOU BUY THE CURVE HOSE FOR THROTTLE BODY. DONT TRY TO USE STRAIGHT HOSE IT WILL KINK AND CAUSE NO COOLANT FLOW.WHEN YOU ARE DONE.FILL COOLANT BACK TO CORRECT LEVEL AND BLEED COOLANT SYSTEM.

Oct 25, 2009 | 1998 Chevrolet Lumina

1 Answer

Chevy lumina starts then stalls


loose connections at coil pack or alternator,fuel not reaching fuel injectors properly,vacuum leak at intake gasket between intake manifold/ plenum and throttle body.

Apr 04, 2009 | 1996 Chevrolet Lumina Mini

1 Answer

Fast idle


your fast idle problem might be caused by your coolant temperature sensor not getting a good flow of hot coolant. The sensor is mounted up on top of your throttle body. Here's a test: after you have just made a trip, put your fingers on the area where the coolant temperature sensor is. It should be very hot, but I suspect yours will be only lukewarm. Unless that sensor gets hot, your computer will stay in the "warmup" mode forever. Your idle speed will not be controllable, your fuel mileage will be poor and your engine will run a little hotter than normal. The coolant flow needs the throttle body to pass fluid freely and also your interior heater core is part of that flow, so that can't be obstructed either. The coolant flow ports are very narrow and sometimes they get a piece of gasket sealer caught in the throttle body. Get some air and blow it out. Good Luck, friend.

Dec 16, 2008 | 1993 Geo Metro

2 Answers

97 chevy lumina -Recharging refrigerant


Underneath the air filter. It should be a Aluminum line
he is Correct but dont go to the left side and try to hook up to the Gas Line

Aug 07, 2008 | 1997 Chevrolet Lumina

Not finding what you are looking for?
1993 Chevrolet Lumina Logo

438 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...