Question about 1994 Isuzu Rodeo

1 Answer

Starter motor shot!

Where is the starter motor on a holden rodeo 1994 manual??? this is also a petrol engine if this helps cheers

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 99 Answers

The starter assmelby is mounted near the gear box transmission system in most of the vehicle so see for it . as you mention the vehicle the vehicle is an SUV most of the SUV hold the starter motor near the Engine Gear box housing so see for it  or for more trouble free hazard free solution do see your nearest ISUZU or GM authorised service station...till then have safe driving & happy motoring see you soon sir...!

Posted on May 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can a petrol gear box go into a diesel engine 4wd Holden rodeo RA


if manual transmission , no problem
if automatic transmission , torque converter different

Jul 10, 2017 | Holden Cars & Trucks

1 Answer

Head bolt torque settings and order for 24litre petrol engine Austalia Holden rodeo Isuzu motor c24se Holden Rodeo 2003


this is USA forum
not a single HOLDEN here
not a one.
why ask us,
why not join , real forum that covers your country

http://www.planetisuzoo.com/

Mar 12, 2017 | Isuzu Cars & Trucks

2 Answers

Where is the fuel pump located?


more info like year model engine size petrol or diesel

Mar 15, 2016 | 1993 Isuzu Rodeo

1 Answer

Is it possible to fit a manual gear box to an automatic 1996 2.6 petrol holden rodeo?


You should be good as long as you replace the flywheel on the automatic engine with the one from the manual. You may also have to replace some sensors once you get it up and running because a manual will drive different that the auto and your pollution control will likely act up by turning on codes.

Sep 01, 2014 | Cars & Trucks

1 Answer

Rodeo petrol starts but wont rev


Holden Rodeo 1989 2.6mpi , start and only runs for 2 or so seconds themselves stalls, after putting on a fuel peesure gauge, fuel looked okay and slowly dropping, found the ECM relay was intermittently switching on and off, gave it a tap and the engine kept on running, relay not repairable, replace with new part. Located in the fuse and relay box on the right hand side of engine bay next to battery. Hope this helps.

May 24, 2012 | Holden Rodeo Cars & Trucks

1 Answer

What do i need to remove so i can get the starter motor into its place on a 2004 holden rodeo


if V6 you need to support engine with jack remove left engine mount and bracket via left wheel arch area then can remove starter motor from same point.

Nov 03, 2009 | 1994 Isuzu Rodeo

2 Answers

I have a 1990 holden(isuzu)rodeo 2.8 pertol.Ihave just put some fuel in the thing and about 1 minute down the road experinced some missfiring.this went on for about another 30 seconds and the engine just...


I have a 1996 holden rodeo 2.6 petrol, it misses badly on accelleration, I have replaced plugs, leads, distributor cap, and run injector cleaner through... it idles ok,,,,

Sep 06, 2008 | 1994 Isuzu Rodeo

1 Answer

Holden 94 rodeo petrol


Good Day
Vale clearance cold
intake .006 in (.15 mm)
exhaust .010 in (.25 mm)

Timing
1. With transmission in Neutral or park, start engine and warm to normal operating temp. turn eng,and all accessories off. connect Tachometer. Connect timing light to no 1 spark plug wire.

2. Disconnect and plug fuel vapor canister purge hose and EGR vacuum hose. Start and ensure idle is 900 RPM. adjust idle as required. Check ignition timing ( 12 @ 900)

3. If adjustment is required, loosen distributor hold down bolt and turn until timing is within specification. Tighten distributor hold down bolt and recheck timing. adjust idle speed as required.

hope this helps

Cheers

Aug 18, 2008 | 1994 Isuzu Rodeo

Not finding what you are looking for?
1994 Isuzu Rodeo Logo

411 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...