Question about 1994 Mitsubishi Expo

1 Answer

Blinker lever not automatically disengaging

How do I get to the blinker lever? Can't figure out how to get the stearing wheel off. Best I can tell, the back half of the wheel might pop apart, but I'm not sure. Can't seem to get it to separate. Not sure if any other way to get to the blinker switch and replace it if I need to.
The blinker works left and right, but when you turn the wheel, it never turns off the blinker.

Posted by on

  • lytesp33d May 24, 2009

    Isn't there a nut of some kind that holds it on? Or does it just pull off. I can't even seem to get any part of the cover apart on the wheel itself.


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 316 Answers

You need to use a "steering wheel puller" to remove the steering wheel. You will not gain access to the turn signal switch without the steering wheel removed.

Posted on May 24, 2009

  • its420_us May 24, 2009

    Your rating says fix it yourself with no help from me.


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why does my 255 massey wants to free wheel down a hill

check that the gear box is not jumping out of gear when over driven. That the ratio box is not disengaging ( high /low gear lever). IN some instances when you stand on the brakes it will automatically disengage the pto so check the positioning of the brakes .

Sep 11, 2014 | Cars & Trucks

1 Answer

Cruise control broken off stearing wheel on crysler sebring 2007

if you are talking about the lever, this requires removal of the steering wheel. Check ebay for part and it should tell you all cars it will fit. If you are not ok with removing air bag, steering wheel, get the part and bring it to a mechanic.

Mar 15, 2014 | 2007 Chrysler Sebring Sedan

1 Answer

1996 Ford Explorers Blinker doesnt work

Sounds like the electric flasher relay is defective.

Apr 13, 2012 | 1996 Ford Explorer

2 Answers

Key wont turn in ignition on stearing column, How would I disengage air back so it will not deploy when removing stearing wheel? Thanks

Have you tried turning the steering wheel hard to the left or right when turning the key to make sure that the wheels werent turned when you shut it off and caused the power steering to jam against the steer lock mechanism. This will happen and the key will not turn.

Jun 11, 2011 | 1995 GMC Sierra C1500

1 Answer

I can't Desactived the four wheel drive where is the switch for the four wheel drive, is a GMC YUKON DENALI 2007

{: ) If your vehicle has an AWD (All-Wheel Drive) feature, engine power is sent to all 4 wheels all the time. This is like four-wheel drive, but there is no separate lever or switch to engage or disengage the front axle. It is fully automatic, and adjusts ityself as needed for road conditions.

Jan 07, 2011 | 2007 GMC Yukon Denali

1 Answer

Replacing rear drum brakes. Need good diagram to indicate how to put it back together.

REMOVAL & INSTALLATION Light Duty Systems Fig. 1: Light duty brake system components 88489g21.gif
  1. Raise and support the vehicle and remove the wheel and brake drum from the wheel to be worked on. NOTE: If you have never replaced the brakes on a van before and you are not too familiar with the procedures involved, only dissemble and assemble one side at a time, leaving the other side intact as a reference during reassembly.
  2. Install a clamp over the ends of the wheel cylinder to prevent the pistons of the wheel cylinder from coming out, causing loss of fluid and much grief.
  3. Contract the brake shoes by pulling the self-adjusting lever away from the starwheel adjustment screw and turn the starwheel up and back until the pivot nut is drawn onto the starwheel as far as it will come.
  4. Pull the adjusting lever, cable and automatic adjuster spring down and toward the rear to unhook the pivot hook from the large hole in the secondary shoe web. Do not attempt to pry the pivot hook from the hole.
  5. Remove the automatic adjuster spring and the adjusting lever.
  6. Remove the secondary shoe-to-anchor spring with a brake tool. (Brake tools are very common implements and are available at auto parts stores). Remove the primary shoe-to-anchor spring and unhook the cable anchor. Remove the anchor pin plate. Fig. 2: Use an appropriate tool to disengage the retracting springs 88489g22.gif

  1. Raise and support the vehicle.
  2. Remove the wheel and drum. Fig. 4: Common heavy duty drum brake assembly 88489p45.jpg
    Fig. 5: Remove the brake drum from the rear axle 88489p31.jpg
    Fig. 6: Remove the parking brake lever retaining nut, located behind the backing plate 88489p32.jpg

  3. Fig. 7: Disconnect the adjusting cable from the anchor pin, cable guide and lever 88489p34.jpg
    Fig. 8: Slide the parking brake lever out from its mounting 88489p36.jpg
    Fig. 9: Disconnect the parking brake cable from the lever 88489p42.jpg
    Fig. 10: Use an appropriate tool to disconnect the return springs from their retaining holes 88489p37.jpg
    Fig. 11: Disengage the hold-down springs from the retaining clips on the backing plate 88489p41.jpg
    Fig. 12: Back off the adjusting screw and remove it from the brake assembly 88489p40.jpg
    Fig. 13: Spread the shoes apart and remove them from the backing plate 88489p39.jpg

Oct 09, 2010 | 1990 Ford Econoline

1 Answer

Replaced the tie rod ends and the stearing wheel will not lock,

DId you leave steering wheel centered when you did repair?
Is trnsmission lever fully in park?

Jul 03, 2010 | 2002 Buick Regal

1 Answer

2002 saturn columb is lose. need to pull steering wheel, but has air bag. never done it before.

Well , Let me start here if your saturn has tilt first check the lever that lets the stearing wheel go up and down . If that isnt the problem then first you need see if 1 the column its self is loose than you need to remove the plate were your hood release cable is located once you remove the 7mm bolts and the shield look under dash were stearing column is and thier is 4 13 mm bolts that actually hold it up tight against the dash if they are tight follow the stearing column down towards gas pedal thier are two bolts that that go through a bracket from left to right on one side its a 45 mm torxs male and a 14 mm nut check them for tightness if any are loose retighten to factory specs and use lock tight
to remove air bag first unplug batterie then thier are 4 slots on bach side of stearing column I use two flated head screw drivers and push one side and pull out gently once released do the other side the same way ,then thier will be a yellow plug unplug it and air bag is removed
from my experience if the bolts are tight u need a new stearing column witch you can buy used at a resonable price GASTON AUTO GASTON SOUTH CAROLINA i FOUND HAS THE BEST DEALS FOR SATURN
good luck if any other questions please feel free to ask ive worked on many saturns i love them little cars

Mar 26, 2010 | 2002 Saturn L-Series

1 Answer

No Blinkers or flashers. If you hold down the flasher button and try blinker lever, you can get each blinker to flash except driver side front. When you try driver side front, inside indicator blinks fast....

Hi with the blinker blinking fast this tells you a bulb has gone now if you check witch one is working then you will know if its the front or back that needs replacing.
When you know this go and purchase the bulb from any car spares place also the car spares place can tell you the best way to replace the bulb as this varies from model to model.
If you get stuck or need futher assistance then let me know and ill be glad to help

Aug 11, 2009 | 1997 Ford Taurus

1 Answer

My head lights are stuck on high beams, and the turn signal lever will not click them I need to see the inside of the stearing collum, if you have the blue prints of the collum for a GMC Sierra with...

after removing str wheel you'll need str wheel puller ( can rent one at parts store ) remove the leads that connect to cam plate. reverse for installation


Apr 18, 2009 | 1994 GMC Sierra

Not finding what you are looking for?
1994 Mitsubishi Expo Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides