Question about Daewoo Lanos

1 Answer

The fuel injection is not operating on my car (not a Lanos, but a 1.5i Cielo). didn't start,got spark,cranking,got fuel pressure,removed fuel rail & nozzles - no spray on any. Plugged rail into other daewoo, nozzles spray. Where is te control module for FI on these, and fuse/relays?

Posted by on

  • moray5 May 24, 2009

    the plungers are working as i tested them on another identical car. My question was where are the power modules located that power the fuel injectors as it seems that there is no power getting to the injectors. I have fuel pressure to the rail, but no injection happening. All injectors work when attached to the other car, so it is the trigger signal/fuse/power for the injectors that I seek.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,689 Answers

Hi moray,

if you look at the picture below there is a possibility that the plunger is not working or the solenoid does not have any power flowing into it.

you may want to individually to it and check if the solenoids have grounds to check for power.

The fuel injection is not - a547dd3.gif

hope this helps.

regards,

voodoo

Posted on May 24, 2009

  • marlon john madrid
    marlon john madrid May 24, 2009

    the solenoid can be located near the starter as it is synced to the starter solenoid.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 ford explorer xlt 4.0 cranks will not start took to garage changed battery cables and cleaned charging system 2 days later cranks will not start but can hear fuel pump running when I turn key the...


You should hear the fuel pump run momentarily when the key is in the Run position. Ensure the engine has a good spark by removing one of spark plug boots. Stick a phillips screwdriver in the boot, and hold the handle of the screwdriver, and allow the shaft near ground. (motor works best) Have someone crank the engine and look for a good blue spark arch from the screwdriver and engine. If your getting good spark, then check the fuel pressure on the fuel injection rail.

Nov 17, 2014 | 2000 Ford Explorer

1 Answer

2001 suzuki esteem wagon


1.6L or 1.8L vastly different engines... and EFI.
fuel to the rail , only means the pump is active , never good.
28PSI is minimum on all cars. 1psi will never start a car. ever
and the rail will shoot fuel, all day. it fruitless , unless the rail is dead.
see?
First the laws of EFI. (works all gas EFI)
  1. all fuses good.
  2. 12vdc to EFI system , below 10v is bad. (see lamps dim? bingo)
  3. The PCM (EFI brain) will never inject if it sees CMP/CKP or spark primary dead. ever. so, spark is first.
that is double reasons, fuel cant burn if no spark and if ECU
thinks spark is bad it cuts fuel, (fire safety and fuel hydralocking reasons)

so you connect any scan tool to the DLC, OBD2 port , by knees.
and crank for 5 seconds, release key, no turn off
see DTCs (errors) for CMP, or CKP sensors (cam/crank?)
bingo
no, then you crank and look at the RPM PID , live data stream the scan tool, see RPM go to 250rpm cranking, good.
ok , PCM thinks all is good....

i then check the #1 injector with a NOID lamp
i crank it flashes, good.
if not , i do all injectors , if one fails the pcm is dead on this line.
if yes, all dont flash the PCM is seeing some gross errors. ask. why./?
if all flash, then the fuel rail is dead. and your rail test was useless.

until you discloses engine option (size) I cant give spec numbers.
i then connect my fuel pressure gauge $20 tool to the fuel rail test
port, and i get 10psi, FAIL
i check voltage to the fuel pump cranking, i get 8v, bingo bad wiring
or bad fuel pump relay.
say 10psi and 12v at pump cranking,
the pump is bad, or the filter clogged , or the fuel pressure regulator
is stuck wide open killing all legit pressure.

that is how i do it.
keep in mind the PCM cant see fuel pressure on most cars.
some newer cars have this sensors. (nice)
low fuel pressure,. renders the whole EFI , useless. just junk.

Mar 12, 2014 | Suzuki Esteem Cars & Trucks

2 Answers

95 chevy Tahoe will not start, has spark at the coil cranks over fine and gas.


Hi Jonathan, Make sure you have injection as well as fuel in the rail. Sometimes the anti theft unit will cut the injection and therefore the vehicle cannot start. have the vehicle scanned and then rectify what ever defects and faults show up. Another reason for nil injection could be a defective cam or crank sensor. Sometime removing and cleaning them will work. Regards John

Apr 23, 2012 | Chevrolet Tahoe Cars & Trucks

2 Answers

My 2001 Saturn, will start but not stay running. We have checked the fuel pump and all fluids. Did a compression check this morning, fuel injectors are not injecting fuel into fuel rail. Why is engine...


You said, 'fuel injectors are not injecting fuel into fuel rail' but it's my understanding that the fuel rail gasoline is supplied by the pump, and the fuel injectors just pulse to allow fuel to get to the cylinders. I would check out the fuel delivery problem further. Check for pressure in the fuel rail that is within specs.

If not, then the pump or fuel pressure regulator may be the problem. Check the fuse for the fuel pump. If good, then the pump may be bad in the tank.

Good luck on this.

Feb 05, 2011 | 2001 Saturn L-Series

4 Answers

Will not start, what do I look for first


Are ou getting a spark at the spark-plug, and then check to see if fuel is getting to the cylinders.... Please say the year and model, and whether fuel injected or carburetor.... then I can further diagnose.

remember to rate the answer.

Dec 26, 2010 | Ford E-150 Cars & Trucks

1 Answer

Van cranks but will not start


Hi, if the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.

To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. IF it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the schraeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine.

Dec 22, 2010 | 1996 Chrysler Town & Country

2 Answers

My vw will crank but will not start running i


Hi,


If the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the Schroeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine.


Thank you!!

Jun 30, 2010 | 2001 Volkswagen Passat

1 Answer

My car wont start


Hi,


If the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the schraeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine..



Thank you !!

May 30, 2010 | 2002 Cadillac Deville

2 Answers

2001 expedition cranks but wont start


check your crankshaft position sensor

Mar 21, 2010 | 2000 Ford Expedition

1 Answer

Will not start


you need 3 things for engine to run
air
fuel
heat(spark)
usually its fuel or spark that is the missing link
check for spark at h.t. lead by removing one and using screw driver or spark plug or spark tester in lead held away from engine or earth point about 2-5mm and crank engine while watching for spark
check for fuel being supplied at injector rail by removing quick disconnect fitting hose to injector rail carefully with rag under try to remove slowly as soon as fuel spurts out when nearly fully off, is good it means fuel is being supplied this is under pressure if it just dribbles out no fuel being supplied this is if you havent got the right tools for the job
then depending on out come depends where to look next

Jun 02, 2009 | 2002 Daewoo Lanos

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8547 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...