Question about 1997 Geo Tracker 2 Door

1 Answer

Manual transmission will only work in 3rd and clutch hard to pres

You gotta press clutch all the way in to the floor and veryhard to push.... and then it began not goin in 1st and 2nd and grinds

Posted by on

  • billie ramos
    billie ramos May 11, 2010

    do you hav enough fluid in the clutch reservoir? or there could be air in the system........



×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

Needs a new clutch

Posted on May 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota Rav 4. 2002 reg Makes a grinding noise when driven until clutch is pressed to floor the noise disappears


clutch ,slave ,throw out bearing going bad --transmission shaft bearing --bad gear --but would look into clutch since you have o push to floor to have noise stop

Oct 27, 2016 | Toyota Cars & Trucks

1 Answer

When i turn the key the engine wont turn over but i have power to everything but the motor


is the car a manual transmission or an automatic? if manual there is a switch on the clutch pedal that wont let engine turn over unless clutch is pushed to floor.automatic it is mounted on transmission at the linkage.for auto trans you can move shifter back an forth while trying to crank engine. if manual you can push clutch pedal to floor hard an try to crank.

Mar 21, 2011 | 1988 Ford Mustang

1 Answer

How to remove the 5 speed transmission in a 1989 dodge ram 50 to replace the clutch


I can tell you its not easy. I replaced my flywheel. Best way to do it is buy the manual. And make sure you hae a transmission jack. I tried it with a floor jack. But can tell ya though ya got to drop the starter. Top bolt is hard to get to. Gotta disconnect the driveshaft. unbolt it from the motor. But it is recommended to drain the tranny fluid first though

Apr 17, 2010 | 1989 Dodge Ram 50

2 Answers

Manual transmission, have to press clutch all the way to the floor to start car, can this be adjusted


the clutch 'safety' switch is basically a button on a bracket under the dash that is pushed by the clutch pedal lever to only allow the car to start when it's depressed.it's described as 'self adjusting',having to push it to the floor is normal.check condition of switch bracket,that a 'heavy' foot hasn't bent it,look at switch 'pusher' on lever for an adjustment or modification to suit your needs.

Oct 11, 2009 | 2004 Toyota Corolla

1 Answer

1999 honda prelude manual transmission isn't disengaging all the way when i shift, sometimes locking the shifter in gear or not allowing me to up or down shift. I know my master and slave cylinders need to...


This depends as dose it do it when cold or hot.
2nd when you push in pedal and put in gear dose it go in clean or hard to select 3rd can you hear a grinding noise when pushing in pedal and noise goes
when you take you foot off the clutch pedal IF so then its the thrust bearing on clutch REPLACE ALL .4th if you push in clutch pedal and select a gear and let the clutch out if drive right out (replace)

Sep 27, 2009 | 1999 Honda Prelude

1 Answer

2004 Grand Am with manual transmission. Press clutch pedal to floor but does not spring back and cannot shift gears. Is this a hydraulic fluid proplem?


yes,

you have air in the hydraulic system.

get a buddy to push the pedal for you. locate the oil drain on the clutch.

1. pump the pedal couple of times, then press and hold hard to the floor.
2. while holding the pedal, release the drain. after it squirts, re-tighten.

repeat the steps untill the pedal is firm and there is no more air bubles when draining.

Aug 14, 2009 | 2004 Pontiac Grand Prix

1 Answer

Need to know how to bleed clutch for 1995 ford ranger


Does the clutch have the outer clutch slave or is it inside the clutch plate area, to know look on the left or right side for a clutch slave cylinder if it does not have one it's internal and a pain. If it has an out side one fill the master reservoir then go under the truck and crack open the bleed valve on the cylinder have someone pres the clutch pedal all the way down and hold it to the floor, then close bleed valve then allow the clutch back up and have them push it to the floor open bleed valve and close when all air comes out do this till the arm moves it's full travel about 2 inches. And if its one with a master inside the transmission it has to be power bleed and normally you can’t do it without pulling the transmission.

Jul 23, 2009 | 1995 Ford Ranger Supercab

1 Answer

1996 honda ciciv automatic transmission


that could be a result of your clutch being worn.....or worn gears. have it checked by a professional

Jul 28, 2008 | 1996 Honda Civic

Not finding what you are looking for?
1997 Geo Tracker 2 Door Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...