Question about 1996 Chevrolet Tahoe

1 Answer

Installing a distributor

I used the distributor from my old engine , first i turned the crankshaft and lined the mark up with the mark on the block because there is no timing indicator on the front of the block,so the i installed the distributor with the rotor button pointing to the #1 spark plug wire (under the distributor cap) but when i crank the engine it wont start do anyone have a solution

Posted by on

  • 3 more comments 
  • kenneth richardson May 28, 2009

    does the rotor point to the #1 cylinder or the #1 plug wire at the distributor

  • kenneth richardson May 29, 2009

    should i point the rotor button at the #1 cylinder or the #1 cylinder wire at the distributor

  • kenneth richardson May 29, 2009

    engine still wont start, it acts as if it want to .also i smell gas when i keep repeating trying to start the engine,it also makes a hissing noise through the throttle body, i also see smoke coming from the throttle bodyafter cranking the engine,so i guess it's timed right, or do you think the timing is still off

  • kenneth richardson May 29, 2009

    someone told me ,that if i turn the distributor that it would do anthing for the tming on my 1996 tahoe 5.7liter because the timing is set by the computer (so i guess what they told me was wrong

  • Anonymous Mar 31, 2014

    2002sierra. replaced the distributor, tried ligning up with my marking from old rotor. but wont sitt completly where it should??? any help?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 316 Answers

Remove your #1 cylinder spark plug, and bring the piston to the top. Use a straw, or a screwdriver to see when the piston is on top. Place your distributor so the the rotor will point to the number one cylinder (you may have to move the oil pump drive shaft with a screwdriver). From there, you should get the engine to fire, then time it from there.

Posted on May 24, 2009

  • 2 more comments 
  • its420_us May 29, 2009

    You want the rotor to point to the #1 cylinder spark plug wire.

  • its420_us May 29, 2009

    As long as your #1 cylinder piston is on top of the cylinder, and your distributor points to the #1 cylinder spark plug, your timing should be close enough to get the engine to fire. You will have to time the engine, as it won't be exact. As you turn the engine, move the distributor a little to try to find a position in which it will run. After you get it to run, you will need to set the timing. If you can't get it to run from there, your timing chain may not be set correctly.

  • its420_us May 29, 2009

    As long as your vehicle has a "distributor", with a "rotor", you must set your ignition timing.



  • its420_us May 29, 2009

    Are you sure you have your firing order from the distributor to the cylinders correct?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a Distributor install on a 1988 Ford ranger 2.3


First bring the engine up to top dead center and compression stroke confirmed on No 1 cylinder. Next remove distributor cap and verify the rotor is pointing toward No 1 cylinder. Next get a paint marker preferably yellow, and mark on the engine block exactly where the rotor is pointing. Next make a mark on the distributor and the block in line so as to make sure the distributor is aligned exactly in the same location it was removed from. Take note of what direction the pointer moved as you lift the distributor, as the rotor will have to be pointed in that same direction when you go to put the distributor back. It should rotate an 1/8th of a turn as you remove it. If another distributor is being put in it's place, then mark the new distributor in the exact same place as the old distributor where you marked it.

Mar 03, 2016 | Ford Cars & Trucks

Tip

How to Reinstall a Distributor if Crankshaft Moved.


Applys to all Distributor Engines.

Follow this easy instruccions if you want to reinstall a distributor on a vehicle where the crankshaft was moved from the position it was when the distributor was removed.

Remove #1 spark plug

Place your finger over the spark plug hole while turning the engine with a wrench on the pulley bolt at the front of the engine.

When you feel compression continue turning the crankshaft slowly until the timing mark on the vibration damper is aligned with the "0" on the engine timing indicator.

Position the disttributor rotor between the number 1 & 8 (for 8 Cil.) 1 & 6 (for 6 Cil.) or 1 & 4 (for 4 Cil.) spark plug terminals on the cap.

Lower Dist. into engine. To set the gear on the bottom of the distribuitor, you may need to turn the rotor a little bit. If the distributor does not drop down flush against the block is because the distributor shaft has not mated the oil pump shaft, if this happens, place a large socket w/braker bar on the crankshaft bolt and turn the engine over in the normal direction of rotation until the two shafts engage properly and the distributor sits flush against block.

With the base of the distributor properly seated, turn dist. housing to align the marks you made in dist. base and engine block. (you did make this marks before removal right? : )

Place the hold down clamp and install the hold down bolt not too tight.
Install dist. cap an reconect electrical plugs, spark plug wires, etc.

Check ignition timing and when set, tighten dist. hold down bolt.

on Apr 20, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer

How to replace the distributor and line it up the correct way


With ignition OFF, remove the dist cap , do not remove HT leads from cap or plugs just move to one side ,turn the crankshaft with a spanner on the crank pulley drive nut until the rotor arm is pointing directly towards the front of the vehicle, mark the position of the rotor on the distributor body with a dab of paint and also mark the position of the body on the engine block infront of the distrbutor,remove the distributor , i believe it's just 2 screws that clamp it in place ,transfer the mark from old dist to the new dist and aling the rotor to this mark, then fit the new dist to engine and aligne the marks from the new dist to the mark on the engine block and tighten down , refit the dist cap , to get an exact distributor timing you should now use a timing light to check the timing marks line up , if they are slightly out just very slowly turn the distributer until the marks are aligned , hope this is of help

Jun 07, 2015 | 2002 Nissan Xterra

2 Answers

How to remove distributor on 1994 nissan pathfinder


Hi there:
Check this removal procedure (See Figures 1 through 5)

  1. Disconnect the negative battery cable.
  2. Unfasten the retaining clips (only remove the coil wire if necessary) and lift the distributor cap straight off. It will be easier to install the distributor if the spark plug wiring is left connected to the cap. If the plug wires must be removed from the cap, mark their positions to aid in installation.
  3. Remove the dust cover and mark the position of the rotor relative to the distributor body; then mark the position of the distributor body relative to the engine block.
  4. Detach the harness assembly connector.
  5. Remove the pinch-bolt and lift the distributor straight out, away from the engine. The rotor and body are marked so that they can be returned to the position from which they were removed. Do not turn or disturb the engine (unless absolutely necessary) after the distributor assembly has been removed.




6_26_2012_2_15_23_pm.jpg

Exploded view of the distributor assembly-6-cylinder engine




6_26_2012_2_15_51_pm.jpg

Align the mark on the housing with the mark on the shaft-VG30i and VG30E engines


6_26_2012_2_16_14_pm.jpg


After the distributor assembly has been installed, the rotor should be in this position-VG30i and VG30E engines


6_26_2012_2_16_40_pm.jpg

After the distributor assembly has been installed, the rotor should be in this position-KA24E engine



INSTALLATIONTiming Not Disturbed

  1. Insert the distributor in the block and align ALL matchmarks made during removal.
  2. Engage the distributor driven gear with the distributor drive.
  3. Install the distributor clamp and secure it with the pinch-bolt.
  4. Install the distributor cap and fasten the harness electrical connector.
  5. If necessary, install the spark plug wires and coil wire.
  6. Start the engine. Check the timing and adjust it if necessary.

Timing Disturbed
  1. It is necessary to place the No. 1 cylinder in the firing position to correctly install the distributor. To locate this position, the ignition timing marks on the crankshaft front pulley can be used.
  2. Remove the No. 1 cylinder spark plug. Turn the crankshaft until the piston in the No. 1 cylinder is moving up on the compression stroke. This can be determined by placing your thumb over the spark plug hole and feeling the air being forced out of the cylinder. Stop turning the crankshaft when the timing marks indicate TDC or 0 .
  3. Oil the distributor housing lightly where the distributor bears on the cylinder block.
  4. Install the distributor so that the rotor, which is mounted on the shaft, points toward the No. 1 spark plug terminal tower position when the cap is installed. Of course, you won't be able to see the direction in which the rotor is pointing if the cap is installed, so lay the cap on the top of the distributor and make a mark on the side of the distributor housing just below the No. 1 spark plug terminal. Make sure that the rotor points toward that mark when you install the distributor.

On the VG30i and VG30E engines, align the mark on the distributor shaft with the protruding mark on the housing.

  1. When the distributor shaft has reached the bottom of the hole, gently move the rotor back and forth slightly until the driving lug on the end of the shaft enter the slots cut in the end of the oil pump shaft and the distributor assembly slides down into place.

On the VG30i and VG30E engines, the distributor rotor tip should be in the 11 o'clock position.

  1. Fasten the distributor hold-down bolt.
  2. Install the spark plug into the No. 1 spark plug hole.
  3. Install the distributor cap and engage the harness electrical connector.
  4. If necessary, attach the spark plug wires and coil wire.
  5. Start the engine. Check the timing and adjust it if necessary.





Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Jun 26, 2012 | 1994 Nissan Pathfinder

1 Answer

How do i install a distributor to a nissan pick up


It is necessary to place the No. 1 cylinder in the firing position to correctly install the distributor. To locate this position, the ignition timing marks on the crankshaft front pulley are used.

Remove the No. 1 cylinder spark plug. Turn the crankshaft until the piston in the No. 1 cylinder is moving up on the compression stroke. This can be determined by placing your thumb over the spark plug hole and feeling the air being forced out of the cylinder. Stop turning the crankshaft when the timing marks indicate TDC or 0.

Oil the distributor housing lightly where the distributor bears on the cylinder block.

Install the distributor so that the rotor, which is mounted on the shaft, points toward the No. 1 spark plug terminal tower position when the cap is installed. Of course you won't be able to see the direction in which the rotor is pointing if the cap is on the distributor. Lay the cap on the top of the distributor and make a mark on the side of the housing just below the No.1 spark plug terminal plug terminal. Make sure that the rotor points toward that mark when you install the distributor. On the VG30i, align the mark on the distributor shaft with the protruding mark on the housing.

When the distributor shaft has reached the bottom of the hole, move the rotor back and forth slightly until the driving lug on the end of the shaft enter the slots cut in the end of the oil pump shaft and the distributor assembly slides down into place.

When the distributor is correctly installed, the breaker points should be in such a position that they are just ready to break contact with each other or a lobe of the reluctor is aligned with the stator contact. This is accomplished by rotating the distributor body after it has been installed in the engine. Once again, line up the marks that you made before the distributor was removed from the engine. On the VG30i, the distributor rotor should be in the 11:25 o'clock position (between 11 and 12 o'clock).
  1. Install the distributor hold-down bolt.
  2. Install the spark plugs.
  3. Install the cap, primary wire, and vacuum line(s).
  4. Install the spark plug leads. Consult the marks made during removal to be sure that the proper lead goes to each plug. Install the high tension wire if it was removed.
  5. Start the engine. Check the timing and adjust it if necessary.


    Hope this helps, be sure to upvote if it does :)

May 04, 2011 | 1985 Nissan Pickup

3 Answers

I changed the distributor drive gear and i am trying to get the TDC firing position on my 1997 chevy astro van 4.3 and there is only one arrow on the block and two lines on the crank shaft how do get it to...


Hi, the procedure is pasted below. Ignore the timing marks and just verify you are at TDC of the compression stroke on the #1 piston. You can tell compression versus exhaust stroke by plugging the spark plug hole with your thumb while turning the crankshaft (there will be no pressure on the exhaust stroke). Please let me know if you have more questions, and thanks for using FixYa.


Timing Disturbed
  1. Remove the No. 1 cylinder spark plug. Turn the engine using a socket wrench on the large bolt on the front of the crankshaft pulley. Place a finger near the No. 1 spark plug hole and turn the crankshaft until the piston reaches Top Dead Center (TDC). As the engine approaches TDC, you will feel air being expelled by the No. 1 cylinder. If the position is not being met, turn the engine another full turn (360 degree). Once the engine position is correct, install the spark plug.
  2. Align the cast arrow in the distributor housing, the driven gear roll pin and the pre-drilled indent hole in the distributor driven gear. If the driven gear is installed correctly, the dimple will be approximately 180° opposite the rotor segment when it is installed in the distributor.
    NOTE Installing the distributor 180° out of alignment, or locating the rotor in the wrong holes, may cause a no start condition or can cause premature engine damage and wear.
  3. Make sure the rotor is pointing to the cap hold-down mount nearest the flat side of the housing.
  4. Using a long screwdriver, align the oil pump drive shaft in the engine in the mating drive tab in the distributor.
  5. Install the distributor in the engine. Make sure the spark plug towers are perpendicular to the centerline of the engine.
  6. When the distributor is fully seated, the rotor segment should be aligned with the pointer cast in the distributor base. The pointer will have a -6'' cast into it indicating a 6 cylinder engine. If the rotor segment is not within a few degrees of the pointer, the distributor gear may be off a tooth or more. If this is the case repeat the process until the rotor aligns with the pointer.
  7. Install the cap and fasten the mounting screws.
  8. Tighten the distributor mounting bolt to 18 ft. lbs. (25 Nm).
  9. Engage the electrical connections and the spark plug wires.


  10. jturcotte_483.jpg

May 02, 2011 | Chevrolet Astro Cars & Trucks

1 Answer

The timing on my 1987 dodge dakota is way off. how do i fix it?


You will need to adj. your timing to do this>

REMOVAL

  1. Disconnect distributor pickup lead wire at wiring harness connectors.
  2. Unfasten distributor cap retaining clips and lift off distributor cap.
  3. Scribe a mark on the edge of distributor housing to indicate position of rotor as reference when reinstalling distributor.
  4. Remove distributor hold down clamp screw and clamp.
  5. Carefully lift distributor from engine.
INSTALLATION

  1. Position distributor in engine. Make sure rubber 0-ring seal is in groove of distributor housing. Align rotor with marks previously scribed on distributor housing. Clean top of cylinder block to insure a good seal between distributor base and block.
  2. Engage tongue of distributor shaft with slot in distributor oil pump drive gear.
If engine has been cranked while distributor is removed, it will be necessary to establish the proper relationship between distributor shaft and No.1 piston position as follows:

  1. Rotate crankshaft until number one piston is at top of compression stroke. Mark on crankshaft vibration damper should be in line with "0" TDC mark on timing chain case cover.
  2. Rotate rotor to position of number one distributor cap terminal.
  3. Lower distributor into opening, connect pickup coil leads and install distributor cap. Make sure all high-tension wires "snap" firmly in cap towers. Install distributor hold-down clamp screw. Tighten screw finger tight.
    1. Connect distributor pick-up lead wire(s) at wiring harness connectors.
    2. Adjust engine timing to specification (refer to Ignition Timing).
85128526

Basic ignition Timing Adjustment 3.9L Engine

  1. Locate and ground out the carburetor switch idle stop contact with a suitable jumper wire.
  2. Disconnect and plug the vacuum lines at vacuum transducer on the SCC and the air switching valve on the emissions air pump.
  3. Set the gearshift selector in park or neutral and apply the parking brake.
  4. Using a magnetic timing unit, insert the pickup probe into the open receptacle at the left of the engine between the power steering and the water pumps. If a magnetic timing unit is not available, use a conventional power timing light connected to the number one cylinder spark plug wire.
  5. Bring the engine to a normal running temperature. This can be done by allowing the engine to idle for 5 to 10 minutes when the ambient temperature is around 21°C (70°F).
  6. Adjust the engine idle rpm to the specifications on the VECI label in the engine compartment.
  7. Check the basic timing when using a power timing light). If the basic timing is correct, remove the jumper wire, reconnect the vacuum lines and disconnect all test equipment. If the basic timing is NOT correct, proceed to step 8.
  1. Loosen the distributor hold-down bolt allowing the distributor to be turned with some resistance and adjust the basic ignition timing to the specifications on the VECI label. After adjusting the basic ignition timing, recheck the idle rpm and secure the distributor. Recheck the timing once again to verify that the timing is correct.
  2. Remove the jumper wire, reconnect the vacuum lines and check the idle rpm (adjust if necessary), disconnect all test equipment.
  1. Loosen the distributor hold-down bolt allowing the distributor to be turned with some resistance and adjust the basic ignition timing to the specifications on the VECI label. After adjusting the basic ignition timing, recheck the idle rpm and secure the distributor. Recheck the timing once again to verify that the timing is correct.
  2. Remove the jumper wire, reconnect the vacuum lines and check the idle rpm (adjust if necessary), disconnect all test equipment.

Mar 06, 2011 | 1987 Dodge Dakota

2 Answers

When setting the ignition timing on a 1991 ford ranger 3.0 were dose the rotor need to point, after number one or before number one? the engine is on top dead center


The engine timing markers down on the harmonic balancer/crankshaft pulley should be aligned with the timing indicator on the engine block to "0" degrees when the engine is in the compression stroke for the #1 cylinder, and this is TDC or "Top Dead Center". When something blows out of the spark plug hole that only means that the piston is coming up on TDC, but the crankshaft will still have to be turned until the timing markers are at "0" degrees. You should be sure that you do know how to properly align the timing marks to "0" degrees, and the timing marks must be set at "0" degrees before the distributor can successfully be installed.

Be certain that the timing marks are set at "0" degrees and on the compression stroke for the #1 cylinder, or the timing will be 180 degrees off when you install the distributor. This has to be precise and guessing will not get the distributor properly clocked in so that the ignition timing can be correctly set.

Once you are certain that the timing is set to "0" degrees "TDC", then mark the distributor housing where the #1 position on the distributor cap will be when the cap is installed on the distributor, so that the distributor housing shows a reference mark where the #1 position is, then the distributor should be installed so that the ignition rotor is pointing directly at the #1 position on the distributor housing, or just before the #1 position mark according to the rotation of the ignition rotor. The distributor should be able to turn and point the ignition rotor on either side of the #1 position mark to provide plenty of timing advance or ****** so that the ignition timing can properly be adjusted to specifications after the engine has been started.

Be sure that you follow the proper timing procedure for that vehicle and remove any timing spout connectors that are described in the set timing procedures

Also, be certain that you are actually using the #1 cylinder to set the engine to TDC and to actually time the engine with a timing light. Here is a firing order diagram that should also help to assist you. Let me know if you require any further assistance.






cab28d1.gif

Jun 17, 2010 | Ford Ranger Cars & Trucks

1 Answer

Need to know how to install a new distributor and the firing order for a 4 cyl


Firing order is 1342. #1 cylinder is closest to front. (By pulleys)



See Figures 1, 2, 3 and 4
Engine Not Rotated
  1. Disconnect the negative battery terminal.
  2. Turn the engine over until No. 1 cylinder is at TDC of the compression stroke.
  3. Remove the distributor cap. Remove the wire harness connected to the side of the distributor.
  4. Mark the position of the distributor base in relation to the engine block with white paint or other suitable marking material, for reference when reinstalling the distributor.
  5. Loosen and remove the distributor hold-down bolt and clamp.
  6. Carefully begin lifting the distributor up and out. Once the shaft is clear of the engine compartment, inspect the shaft for cracks in the O-seal, the condition of the shaft drive gear and any other part which could lead to distributor problems in the future.

To install:
  1. Check to make sure the engine is still at TDC. Inspect distributor shaft hole to make sure it is free of dirt.
  2. Rotate distributor shaft until the painted mark on rotor is pointing toward painted mark on engine block made during removal.
  3. Continue rotating rotor slightly so leading edge of the vane is centered in vane the switch stator assembly.
  4. Dip entire distributor gear in engine assembly lubricant D9AZ-19579-D or equivalent.

If installing a new distributor, ALWAYS add engine assembly lubricant to the engine oil by pouring it through distributor hole onto the camshaft gear. Run engine at idle for at least five minutes before driving.
  1. Rotate distributor in block to align leading edge of vane and vane switch stator assembly. Verify rotor is pointing at No. 1 mark on distributor base.

If vane and vane switch stator cannot be aligned by rotating distributor in cylinder block, remove distributor enough to just disengage distributor gear from camshaft gear. Rotate rotor enough to engage distributor gear on another tooth of the camshaft gear.
  1. Install the distributor retaining bolt and tighten so the distributor can just barely be moved.
  2. Install the distributor cap and, tighten screws to 18-23 inch lbs. (2.0-2.6 Nm).
  3. Reconnect battery cable. Start vehicle, and check timing. If timing needs adjustment, refer to the Ignition Timing section.
  4. After timing has been set, tighten distributor hold-down bolt to 17-2 ft. lbs. (23-34 Nm).

Engine Rotated with Distributor Removed
  1. If the crankshaft was rotated while the distributor was removed, the engine must be brought to TDC on the compression stroke of the No. 1 cylinder.
  2. Remove the No. 1 spark plug. Place a finger over the hole and rotate the crankshaft slowly in the direction of normal rotation until engine compression is felt.
  3. When engine compression is felt at the spark plug hole, indicating that the piston is approaching TDC, continue to turn the crankshaft until the timing mark on the pulley is aligned with the 0 mark on the engine front cover.
  4. Turn the distributor shaft until the ignition rotor is at the No. 1 firing position.
  5. Rotate distributor shaft so the blade on rotor is pointing toward paint mark on distributor base made during removal.
  6. Continue rotating rotor slightly so leading edge of the vane is centered in vane switch stator assembly. Verify rotor is pointing at No. 1 mark on distributor base.

If vane and vane switch stator cannot be aligned by rotating distributor in cylinder block, remove distributor enough to just disengage distributor gear from camshaft gear. Rotate rotor enough to engage distributor gear on another tooth of the camshaft gear.
  1. Install the distributor retaining bolt and tighten so the distributor can just barely be moved.
  2. Install the rotor and distributor cap and connect all wiring. Tighten distributor cap to 18-23 inch lbs. (2.0-2.6 Nm).
  3. Reconnect battery cable. Start vehicle, and check timing. If timing needs adjustment, refer to the Ignition Timing section.
  4. After timing has been set, tighten distributor hold-down bolt to 17-2 ft. lbs. (23-34 Nm).

Nov 17, 2009 | 1992 Mercury Topaz

1 Answer

Does a 1991 Dakota 5 2L have a crankshaft position sensor?


no it has a distributor here is the prodeure for the timing sensor under the cap.
  1. Disconnect negative battery terminal, disconnect distributor lead wire at the wiring harness connector.
  2. Release distributor cap retainers and lift the distributor cap off.
  3. Scribe a mark on the edge of the distributor housing to indicate the position of the rotor. Use the mark as a reference when reinstalling the distributor.
  4. Remove the distributor hold down bolt and clamp, and carefully lift the distributor out of the engine.
INSTALLATION

  1. Clean the top of the cylinder block to insure a good seal between the distributor base and block. If the engine has not been cranked with distributor removed, proceed with step 2. If the engine has been cranked with the distributor removed proceed to step 3.
  2. Position the distributor into the engine. Make sure the O-ring seal is in place on the distributor housing. Align the rotor with the mark previously scribed on the distributor housing. Engage the tongue of the distributor shaft with the slot in the distributor oil pump drive gear. Proceed to step 4.
  3. If engine has been cranked with distributor removed perform the following:
    1. Rotate the crankshaft until number one piston is at the top of its compression stroke. The mark on the crankshaft vibration damper should be in line with the "0" TDC mark on the timing chain case cover.
    2. Rotate the distributor rotor until it is positioned pointing at the number one distributor cap terminal.
    3. Lower the distributor into the engine, making sure the O-ring seal is in place. Engage tongue of distributor shaft with slot in the distributor oil pump drive gear.
  1. Install the distributor hold down clamp and screw and tighten finger tight. Install distributor cap and wires, making sure all high tension wires are firmly secured in cap towers.
  2. Connect pick-up leads and negative battery cable lead. Set ignition timing, refer to ADJUSTMENT PROCEDURES for timing adjustment

Feb 01, 2009 | 1991 Dodge Dakota

Not finding what you are looking for?
1996 Chevrolet Tahoe Logo

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...