Question about 2004 Chrysler Sebring

1 Answer

Front right passanger window motor need to be repace, I have taken off the panel but unsure on how to get the motor out

I need help on how to remove the motor window from right passander door for my 2004 chrysler sebring.

Posted by on

  • genicyber May 23, 2009

    how do you exactly remove the motor, as i unscrew the screw that is holding the motor, the window will fall down, must i remove the window first inorder to get access to motor? if so how can i remove the window

  • rfmtm May 25, 2009

    Should you if you can, remove the window before you remove the regulator. Or does it all have to come out together?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 316 Answers

First disconnect your negative battery cable. Next locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Once you have removed the interior door handles, unplug the wire clips to the switches. Next you will need a small pry bar to remove the door panel itself. The door panel is held in place by snap in clips; try to get the pry bar as close to, or directly under the clips, to prevent them from tearing out of the door panel. Once you have removed the clips, pull the panel upward to remove it from the door. You will need to remove the plastic sheeting to gain access to the window regulator. You will need to remove the regulator and motor as a single unit, and once it's removed you can replace the motor.
Install everything in reverse.

Posted on May 23, 2009

  • its420_us May 24, 2009

    You will have to support the glass when you remove and replace the regulator. A second pair of hands is best, but if not available a few pieces of duct tape will work. After the regulator is removed, the glass can rest inside the door until you're ready to replace it.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Passanger window wont roll up from driver side or passanger side


Replace the regulator. It comes with the motor. You have to remove the door panel to access it.

May 26, 2015 | 2006 Kia Sorento

1 Answer

1997 kia sportage Passenger power window stopped working from both driver's side and passanger side. Which door panel do i remove? What Next?


Sounds like the motor is bad.remove passenger panel check for voltage at motor ,if no voltage wiring is broken .if there is voltage replace motor

Jul 20, 2014 | 1997 Kia Sportage

1 Answer

How to remove passanger side door panel 2012 auston martin db9


Its just fitted with few screws and hidden lock clips.The clips are very delicate and can break easily.But no worry,the clips are easily available.
on some vehicle models these screws are hidden.Once the panel is loose, don't just pull it out,there are few wire connectors connected,first disconnect the connector plug,then lift the panel out and keep in safe place for re-installing.
For your help,there are few very helpful similar help links with diagrams and solutions to make your task easy.Click the link below:----How to Remove Door Panels on Acura Integra
http://repairhelpcenter.blogspot.com/2011/11/how-to-remove-door-panels-on-acura.html

-------How to Access car door panel?
http://howtobyme.blogspot.com/2011/11/how-to-access-car-door-panel.html

---------

Vehicle door panel components?
http://howtobyme.blogspot.com/2011/11/vehicle-door-panel-components.html
----------How to remove the door panel to install a new window regulator on Cadillac Deville?
http://howtobyme.blogspot.com/2011/08/how-to-remove-door-panel-to-install-new.html
---------------
Hummer H2 Door Panel Removal? http://technoanswers.blogspot.in/2012/07/hummer-h2-door-panel-removal.html
------- Hummer H2: How to remove Front Door panel? http://www.howtobyme.blogspot.com/2012/07/hummer-h2-how-to-remove-front-door.html
-------------- 2009 Hummer H2 Door Panel Removal http://schematicsdiagram.blogspot.in/2012/07/2009-hummer-h2-door-panel-removal.html
-----------how to remove window motor on driver side door panel on 1994 Oldsmobile Cutlass Ciera
http://technoanswers.blogspot.com/2011/08/how-to-remove-window-motor-on-driver.html
------------How to remove door panel, door window motor and regulator on 1991 cavalier?
http://technoanswers.blogspot.com/2011/05/how-to-remove-door-panel-door-window.html
-------------
how to remove rear window inner panel on Hyundai Elantra?
http://technoanswers.blogspot.com/2011/05/how-to-remove-rear-window-inner-panel.html
------------
ford explorer window motor, regulator and door panel removal?
http://technoanswers.blogspot.com/2011/02/ford-explorer-window-motor-regulator.html
------------
These details will help.
Thanks,.

Nov 23, 2012 | Cars & Trucks

1 Answer

Electric window assembly removal


assume you mean window motor.

remove trim panel. long screws (2) AT ARM REST. dRILL 3/8 INCH HOLES (3) AT THE DIMPLES in the inner panel, for access to the 3 bolts holding the motor in.
from 1994 manual.

Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, proceed to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    1. Mark inner door panel and drill three holes 12.7mm (0.5 inch) as shown.

56b2b8c.gif

Oct 28, 2010 | 1992 Mercury Grand Marquis

1 Answer

Two weeks ago the drivers side rear wind stoped operating and is in the up position. All other windows were working ok. Yesterday the passanger side rear window stoped operating. Fuses are ok and I hear...


Not really i think your right, it sounds like both motors went bad a quick little test i always do is hold switch down and bang on the inside of the door at lower front of door and sometimes it shakes motor and it starts working then i know for sure its a motor, this save cuatomers money , they dont pay to remove panel and testing,try it . hope this helps.

Aug 29, 2010 | 2006 Lexus Es 330

1 Answer

The pass side window will not work,the pass side seat will notmove,nothing that is controlled on the pas side door works except the lock


WELL REPLACE THE MOTOR ON PASS SIDE AND THAT SHOULD FIX IT MANY ISUSE BUT IF YOU YOU HAVE ARE GOOD WITH ELEC THEN YOU CAN PULL UP ROKER PANEL ON FRONT PASSANGER SIDE YOU NEED TO FIND THE BUSS LINE AND THEY SHOULD BE BROWEN WIRES AND YOU UNPLUG ONE AT A TIME IN TILL THE SEAT OR WINDOW STARTS WORKING THEN THATS THE MOTOR COUSING THE ISUSES BUT IT NOMALY THE RIGHT REAR WINDOW MOUDUAL WITCH IS THE MOTOR HOPE THIS HELPS

Aug 19, 2009 | 2000 Mercedes-Benz S-Class

1 Answer

Replace the power window motor


First door panel has to be removed, If i remember correctly there are 3 or 4 rivets that have to be drilled out to remove motor from window regulator, and unplug electrical connection, and it should come out. Replacement motor will have new blots and nuts to secure new motor back on to regulator.

Mar 04, 2009 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Right front window not working


If only one window is not working the issue is not with power to the window, there are three things that can cause this, the most common is the control switch, have you tried the window from both switch's, pass door and driver door? next is the window motor itself is defective, and last and least common is a wiring issue to the motor, the door panel will have to be taken ff to repair the window motor if that is the problem, the switch can be replaced without removing the door panel, it just pops out.

Oct 27, 2008 | 1998 Lincoln Town Car

1 Answer

Replace actuator cable for front driver side window motor


I also Have this problem, just happened, is their a way to repace this

Jun 20, 2008 | 2002 Oldsmobile Alero

2 Answers

2000 dodge caravan window motor


You have to remove the door panel first, After the door panel is removed you have to remove the window motor AND the cable system in the door. When you install the replacement window motor/regulator, you'll have to slightly modifiy the inside of the door frame for it to set in properly, when you get to that point you'll see what I'm talking about.

May 16, 2008 | 2000 Dodge Caravan

Not finding what you are looking for?
2004 Chrysler Sebring Logo

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...