Question about 2000 Lexus RX 300

1 Answer

Can't locate thermostat on 2000 RX300 Lexus

Need specific location of thermostat

Posted by on

  • fastdan60 May 24, 2009

    there is only 1 hose from radiator to engine block...thare are multiple bolts and attachments at this location?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Lexus Master
  • 3,433 Answers

Follow the big rubber hose from the radiator to the engine. the top readiator hos. If at the engine there is two bolts holding down the hose connection housing, You found iit. If not there, look on the block end of the lower host.

Posted on May 23, 2009

  • Ned C Cook
    Ned C Cook May 24, 2009
  • dunthat Sep 04, 2011

    There are 3 10 mm nuts and it is not easy. It is on the driver side under the intake manifold - follow the lower radiator hose back. You have to remove air filter housing and hoses and wire harness to access the t-stat housing - then there is a solid hose on the housing which will hit the starter - so you may be removing the starter.

    Dear co7196 - Please do not advise people if you haqve never worked on the subject car. Bad advise is worse than guessing.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have check engine code P1354 variable valve timing system bank 2 for my 2000 Lexus RX300. Where is this located?


YES, you have to investigate what is throwing your valve timing off. That could be anything from a vacuum leak to clogged injectors, bad plugs, sensor ect. Have the car analyzed to find the cause. There can be many causes. Good luck

Mar 22, 2017 | 2000 Lexus RX 300

2 Answers

Where is thermostat for lexas 2000 rx300 located


FOLLOW WATER INLET HOSE TO CYLINDER BLOCK.YOU WILL SEE THERMOSTAT HOUSING.

Mar 03, 2011 | 2003 Lexus RX 300

2 Answers

Having trouble finding thermostat 2000 lexus rx300


Standing in front of your car there should be a large hose on the top of your radiator on your right hand side(passenger). follow that hose towards the engine. The housing that it runs into holds the thermostat It should be held on with 2 bolts. Hope that hels you out.

Dec 19, 2010 | 2000 Lexus RX 300

1 Answer

I am needing a door lock actuator (passenger door) for my 2000 Lexus RX300. Do you know of any parts places besides Lexus where I might find one ?


Try to find your solution here, from Germany Lexus Owners:

QUOTE
I justreplaced my door lock actuator on my 2003 Lexus RX300. A rather comprehensive set of instructions for removal of the door panel can be found at: clublexus.com door+panel+removal

To remove the door handle trim: after removing the screw in the door handle trim, pry (I use a painters 5 in 1 tool) the trim piece outwardsfrom the rear of the door panel at both the top and bottom of the trim piece. This will release the two small rear clips. Then push the trim forward to release the main clip located on the back side the handle trim piece

As the least expensive OEM replacement door lock actuator for Lexus RX300 is $230 or more, I opted for the $15 replacement option as outlined below: us.lexusownersclub.com/forums

Keep in mind that this job outlined above is a bit on the technical side.If you aren't that talented, spend the money and order a OEM Lexus replacement latch actuator and do the installation as the OEM latch assembly is not repairable.

Viel Gluck (good luck in German)
END QUOTE

I hope helps with this. Good luck.

Dec 29, 2009 | 2000 Lexus RX 300

1 Answer

Transfer and Differential oil change for RX300


your front wheel drive rx300 doesnt use gear oil, the differential is lubricated internally by transmission fluid. the trans fluid is only reccomended if its dirty. if its a dark brownish red thats normal. or if its pinkish red then its new. if its black or yellow then time to flush it out. if you decide to change the trans fluid I believe the spec is 3qts. check it with the engine running and cold. thats the most accurate way to check it.

Oct 07, 2009 | 2000 Lexus RX 300

3 Answers

I have a 2000 lexus rx 300. clicking arond or near center consul


the location and type of noise u hear is most likely coming from the electric blend door temperature control actuator.when they fail the ting gears inside make a clicking noise like this, the location you gave is dead on to where this part is located.

Aug 27, 2009 | 2000 Lexus RX 300

1 Answer

Replacing outer tail light on Lexus RX300 ?


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-fareast-font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Lift the hatch. The tall center light is located behind the upper hatch inside panel. There are two panels need to remove. One panel is on the right, the other on the left. To remove the panels you have to use flat screw driver to pry out the panel in several locations. (These panels are secured by several small metal clips.) Be careful to collect all these clips and replace them on the back of the panel. You will need these clips to replace the panel later on. After remove the panels, you will be able to locate the screws on the tall center stop light assembly. Remove those screws and cover. After replacing light bulb. Assemble everything in reverse order. Remember, the metal clips have to set on the back of the two panels not the car body.

Jul 04, 2009 | 2002 Lexus RX 300

Not finding what you are looking for?
2000 Lexus RX 300 Logo

Related Topics:

518 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...