Question about 2000 Chevrolet 3500

2 Answers

Will crank but will not fire

2000 3500 chevy pickup ...It will crank but will not fire.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I would assume the ignition control module. I had the same issue w/ 1993 K1500 and wasn't getting fuel or fire... replaced the ignition control module and it fixed it.

Posted on Jun 03, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 1,348 Answers

Get a spark tester,if there is spark then there is a fuel problem.put fuel spray into the throttle body and see if it starts and dies out.
then it is the fuel pump perhaps.
there are crank and cam sensors that could be a problem. or the ignition module .best thing is to scan it and see if any codes show to point out the defective system.

Posted on May 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1986 chevy van g20 cranks but wont start no fire replaced cap,rotor and coil .


I would suggest changing the pickup in the bottom of the distributor. Also crank the engine with the cap off of the distributor and make sure that the rotor bug is turning and make sure there is 12v at the coil with the key on.

Oct 03, 2016 | Cars & Trucks

1 Answer

Crank Shaft Sensor for 2.5E 1991 Chevy S10


you mean it cranks fine but wont fire? When you installed the distributor did you set it in exactly where it came out? like where the rotor was pointing and or was it on top dead center pointing at number one on the distributor?

Apr 11, 2014 | 1998 Chevrolet S-10 Pickup

1 Answer

2002 chevy s10 turns over but will not fire after changing clutch


Are you saying, It cranks but doesn't start? You might have some wires pinched between the transmission and engine at the top.

Feb 09, 2013 | 1998 Chevrolet S-10 Pickup

1 Answer

Cranks but won't start.


It should be tune up as replace the cap, rotor, spark plugs, wires, PCV vale and Mass flow meter. so many problem when this happen.

good luck!

Nov 19, 2009 | 2000 Chevrolet Silverado 1500

2 Answers

97 1/2 ton 4x4 chevy wont start


first thing to do is after trying to start engine, remove a plug, see if its wet or dry. if dry, no fuel getting there, if wet, ignition problem, then we willl take it from there

Oct 19, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

1988 Chevy S10 Durango Pickup, Won't start will fire


sounds like ignition module inside of distributor cap under distributor rotor button.these do go bad and can easily be replaced.strong suspicion from your details that this is the culprit.

May 09, 2009 | 1988 Chevrolet S-10

Not finding what you are looking for?
2000 Chevrolet 3500 Logo

360 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...