Question about 1994 Honda Civic

1 Answer

I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

I need instructions on how to replace rear wheel bearings on a 1994 Honda Civic

Posted by on

  • Anonymous Mar 18, 2014

    It jerks bad in first gear when i first start it up

  • Anonymous Mar 20, 2014

    Blue blinking light under steering wheel for 2014 honda civic

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,623 Answers

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2002 honda civic with noise coming from rear sounds like a noisey wheel bearing have jacked up both sides and spun wheels with no sign of noise .


Check Tires for feather edge. Join your fingers together, move around the rear Tire from front to back and vice versa on both of the rear Tires and feel the smoothness. If the tread of the Tire resist the fingers in one direction and smooth on the other, then the Tires may be producing the abnormal noise.
Temporarily bring both the front Tires to the rear and rear Tires to the front on the same side, drive the car and watch the noise. If the noise begins to come from the front end, then the Tires are defective and need replacement. . If the noise still comes from the rear wheels then the rear wheel bearings need replacement.(You can also rotate the Tires in criss cross manner temporarily)
The bearings often vary noise with and without load. Be sure to troubleshoot the noise before spending money on costlier spares.

Feb 23, 2013 | 2002 Honda Civic

1 Answer

Front wheel baring


Strip out front hub carrier,remove hub unit {a puller will be needed for this operation.There is a circlip holding the bearing in this needs to be removed. A press will be needed to remove and replace the bearing assembly. reverse strip down operation...Good-luck...

Jan 04, 2013 | 1994 Honda Civic

1 Answer

The rear wheel bearings on my 1998 Honda Civic Aerodeck are rumbling and I need to know how to replace them or regrease and is it a DIY or garage job


Your vehicle is equipped with sealed bearings that are pressed into the hub assembly. If your rear wheel bearings are making noise, you must replace the entire bearing and hub assembly (they cannot be greased).

To replace it, raise and support the vehicle and remove the tire and wheel assembly. Remove the brake drum. Remove the bearing cap, the spring nut and the axle washer. Remove the hub assembly and hub seal. The new hub assembly should come with a new hub seal installed. (See first picture below)

TIP: The brake drum has threaded holes in its face where an 8mm bolt can be inserted to help "push" the drum off of the hub assembly - they can get really stuck. (See second picture below)


dttech_22.jpg


dttech_90.gif

May 22, 2011 | Honda Civic Cars & Trucks

1 Answer

I have a 95 honda civic 2dr coup. when ever the car is in motion i hear squeeking/ grinding from the rear breaks. I don't know what could keep causing this. I just replaced the rear break pads, drum...


you may need a hub bearing. do you know which side? they're relatively easy to check; just jack up rear of car, release e-brake and rotate each wheel, listening for any noise or rumble; another way is to place your hand on the coil spring while spinning the wheel, as any rumbling that can't be heard will be felt in the spring. hope this helps.

Mar 07, 2010 | 1995 Honda Civic

1 Answer

Honda Civic 2007 Civic . Cahange wheel bearing and


sorry to tell you this but it sounds like the wheel bearing was put in backwards on one or both sides. the front wheel bearings have a black speed ring built in and that is what your speed sensor reads off. - this is common as the front bearings will install either way- hope this helps

Dec 12, 2009 | 2007 Honda Civic GX NGV Sedan

1 Answer

How tight should i make the axle nut after fitting new rear wheel bearing assembly if i don't have a torque wrench


tighten the nut down and spin the hub to set the bearings and then back it of a 1/4 turn

Oct 17, 2009 | 1994 Honda Civic

1 Answer

Rear wheel hub


IF IT HAS REAR DRUM,WITH WHEEL REMOVED,REMOVE BRAKE DRUM,KNOCK OFF CENTER BEARING CAP,REMOVE STAKED LOCK NUT,AND PULL OF HUB AND BEARING ASSEMBLY.

Apr 07, 2009 | 2001 Honda Civic

1 Answer

Wheel bearing trouble


This probably is a job you should leave for a good shop. I'm not saying that to discourage you. This style of wheel bearing requires the use of special pullers and installer tools. I have seen many experienced techs screw this job up. Because of the way the bearings are made, they have to be removed off the hub flange and installed in the knuckle with extreme care or the bearing will be damaged. If you do go ahead with this at home, have some very experienced help handy, this is not a job you can do over the internet.

Mar 11, 2009 | 2002 Honda Civic

1 Answer

Rear Brake conversion


I have been wanting to do the same to my car and yes you do need to replace the boosters from one w/disc brakes

May 21, 2008 | 1994 Honda Civic

Not finding what you are looking for?
1994 Honda Civic Logo

996 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...