Question about 1995 Geo Prizm

1 Answer

When i push the clutch in it won't go into gear

When i push the clutch in i can't put my car into gear

Posted by on

  • mathew_roddy May 11, 2010

    this starts after driving a few minutes< wher is the master on a 95 geo?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

Check the master cylinder resevoir and make sure you have sufficient fluid. Hopefully it isn't your tranny.

Posted on May 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Honda Civic manual trans will not shift into gears. Car starts, push in clutch and it goes to the floor, release clutch and comes back up. Unable to put into gears. Brake fluid and clutch fluid seem...


Eric, how are you confirming whether or not the car goes into gear if you shift gears without the engine running? One way would be to put it in 1st and see if you can push the car. If you can't, it is in gear.

Another option is to roll the car slightly forward or backward (engine off) while trying to put the car in gear. Once it is in gear, then the car shouldn't move any further. However, if it goes into gear, DO NOT start the car without taking it back out of gear.

The clutch is much more likely to be the problem than the transmission.

If the clutch fluid ever ran dry, then the clutch hydraulics will need to be bled of air. Otherwise, the problem could be the clutch master cylinder, slave cylinder or throwout bearing. Since you didn't report the clutch slipping (e.g. engine revving without accelerating when in gear) it is likely not the clutch disks themselves.

Jun 11, 2014 | Cars & Trucks

1 Answer

I have a 1989 Toyota pickup v6 and when I push the clutch in and try to put it in gear it won't go what could be the problem? Btw the clutch pedal is stiff and has plenty of pressure to it


Could be a bent shift fork or the synchros have gone bad, just first gear that wont go in or all of them? Do they grind at all when you try

Mar 28, 2013 | Cars & Trucks

1 Answer

Suzuki won"t shift into gear unless I turn the car off and put it into first


make your adjustment to clutch, see how that works, but start saving up for a new clutch, or just have your inspection mechanic, take a look @ it for you, make the adjustment, and he can remove a cover and inspect the condition of your clutch with his own eyes. its a lot easyier for him than you. then, you'll know for sure. good luck

Jan 13, 2013 | 2001 Suzuki Grand Vitara

2 Answers

Push on clutch and caR WONT GO IN GEAR UNLESS MOTOR OFF


Some of that model had an unusual clutch mechanism, which has probably broken due to wear. Read here

http://wiki.answers.com/Q/How_to_adjust_clutch_on_1995_ford_escort

In the event yours is instead fitted with a hydraulic clutch, either

- the hose has split
- the clutch throwout lever has broken or collapsed

Mar 21, 2012 | 1995 Ford Escort

1 Answer

My problem is that the manual transmission is stuck in 4th gear. I was backing up when I went to put it into 1st the shifter was stuck. The clutch works to disengage the gears but the shifter won't...


That cylinder is known as the clutch slave cylinder. It should push against the clutch fork every time the clutch pedal is depressed to allow gear changes. If it doesn't, suspect a faulty slave cylinder, or clutch master cylinder.

Sep 09, 2011 | 1999 Nissan Sentra

1 Answer

When you put it in drive or second it won't move when you push the gas but if you put it in 3rd or reverse it will move


theres a problem with the planetary gearing-----valve body------or bands and clutches-----------bring it to an honest shop or visit magicmechanic.net

Sep 04, 2011 | 1999 Oldsmobile Silhouette

Not finding what you are looking for?
1995 Geo Prizm Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7731 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...