Question about 2006 Nissan Murano

1 Answer

I have a toyota corrollashowing oil light

I overhaulled the complete engine fitted new oil pump new bearings and piostons but still my oil light comes on and goes of then i realised the oil not coming to the oilfilter i opend again and cleand the engine block but still aving the same problem wat should i do please help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

It's always difficult to diagnose at a distance but as long as you rebuilt the engine properly and there is a gasket between the oil pump and engine block, and the oil pressure release valve has been checked, I would suggest the following. I think it is possible that the oil pump need to be primed. Remove the oil filter and fill it up with some oil and then replace. If the car has an oil cooler, fill this up also by removing one of the pipes. Finally, with the spark plugs removed, turn the engine over on the starter motor for 2 minutes or until the oil light stays off - you should have no more problems after that. If the light will not go out then you need to go over everything you have done with the help of a manual.

Posted on May 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2004 Toyota highlander leaking oil, oil light comes on. Could it be the rubber rings?


a 2004 toyota highlander V6

this should be your engine type
The 2GR-FE is a 3.5 L (3456 cc)

if leaks are that bad
always check the engine oil level before you drive off

fixing oil leaks on motors
degrease whole motor top and bottom

start with replacing the oil sender it may be the cause of the oil light coming on
after degrease
lay cardboard or paper under the car
take out for a drive and park over the paper over night

this pin points most of the oil leak locations
leaks from a V6 motor
rocker covers/ spark plug tube 0 rings.engine seals
cam seals
front and rear engine seals leak often
sump gasket can leak

if oil consumption or light on continues
can be a failing engine oil pump
or worn main bearings giving low oil pressure to the whole engine
you could be burning oil from worn piston rings
or hardened valve stems

a mechanic can fit an oil pressure gauge to the motor when hot
to check running oil pressure to confirm low oil pressure

if engine is worn out

it is possible to fit a lower mileage used motor to your highlander
its often cheaper than and engine rebuild









26309754-eqpognyxwb4jkumc2nrzorbv-5-0.png

26309754-eqpognyxwb4jkumc2nrzorbv-5-1.jpg

Oct 13, 2016 | Toyota Cars & Trucks

1 Answer

I recently done engine completely on my Toyota conquest 2e engine,but the oil pump isn't pumping the oil up.I've bought the new oil pump still no oil coming up.What must I do please help?


Did you prime the pump before installation? New pumps should be filled with some fluid before you install them, such as engine breakin lube.

Aug 16, 2016 | Toyota Cars & Trucks

1 Answer

I have KIA sorento 2.5 diesel 2009 model and it was overhaul engine and now the the oil lump keeps on flicking when reducing speed or idling after getting warm, What could be the problem


Remove the oil sender unit, fit a oil pressure gauge , start the engine and read the oil pressure at idle engine hot, must read above 10 psi and needle not flicking, must increase with engine speed , if pressure is ok replace censer, if not check oil pump screen and relief vale spring, can also be caused by crankshaft bearings clearance .

Jul 02, 2015 | 2007 Kia Sorento 4x4

1 Answer

Oil light keeps comeing on ???


Remove the electric sender and install mechanical oil gauge to check that you have proper oil pressure. Bet ya the main bearings are not fitted correctly or the engine wasn't cleaned during overhaul and now bearings are trashed.

Jan 19, 2015 | Cars & Trucks

2 Answers

Engine light comes on when engine is hot. Power is the greatly reduced. When engine is cold it drives perfectly. Toyota 7afe 1.8 litre fuel injection, modded aspirated. I've rebuild the motor due to a big...


Hello,
There is a possibility that the old motor was not burning properly and you have carbon build up on the O2 sensers. A poorly functioning O2 senser will not allow the Fuel/Air mixture to work as you give it gas under load. You could have multiple O2 sensers too.

Dec 08, 2014 | Cars & Trucks

2 Answers

I have no compression on my 1998 corolla what could be the problem ?


This phenomenon is called blow by. This usually happens when the engine compression escapes through the worn out piston rings due to the severely scratched cylinder wall. It also happens after the engine becomes severely overheated due to the loss of coolant or the car is driven with ruptured element air cleaner for longer period of time or due to the aging factor.
In this case the engine requires complete overhaul. It includes the replacement of the following parts to help enable the engine to perform satisfactorily as long as for many years without any problem.
The dire requirement here is to maintain the oil clearances of various parts during the machining process to ensure the reliability and dependability of the engine.
Engine parts to be replaced with original:
- Engine valves.
- Valve guides,
- Piston set (oversize).
- Ring set (oversize).
- Main and big end bearing shell set (Oversize).
- Crankshaft thrust (oversize).
- Timing belt and bearing set.
- Gasket set complete kit.
- Oil filter.
- Element air cleaner.
- Engine oil.
- Silicone RTV Grey.
- Radiator coolant.
Machining:
- New valves and guides fitting and valve seat redressing.
- Valve clearance adjustment.
- Cylinder re-boring and honing.
- Crankshaft grinding, main and big end bearings fitting, and main line checking/ correction.
- Connecting rod alignment.
- Radiator cleaning and cooling system inspection.
Hope that works.
Thanks for visiting Fixya.

May 05, 2014 | 1998 Toyota Corolla

3 Answers

Where is the oil pump located on jeep liberty 2002


oil pump is in the oil pan,sounds like your problem is in the crank bearings if one crank bearing goes you will loose oil pressure causing oil light to come on.

Jan 15, 2010 | 2002 Jeep Liberty

1 Answer

How to overhaul an engine?


TO OVERHAUL ENGINE YOU HAVE TO REPLACE ALL WORN PARTS.LIKE VALVES + SEATS+ GUIDES.+ SEALS. ALSO YOU HAVE TO REPLACE CAMSHAFT AND GEAR+ LIFTERS NEW CAM BEARINGS.NEW OIL GALLORY PLUGS AND FREEZE PLUGS.THE CYLINDER BLOCK HAS TO REBORED BEFORE INSTALLING.NEW PISTONS + RINGS+ CRANKSHAFT AND BEARING HAS TO BE REPLACED.ALSO OIL PUMP TIMING CHAIN.AND CRANKSHAFT GEAR.IT WOULD BE A WHOLE LOT CHEAPER TO BUY REBUILT ENGINE THEN TO REBUILD.BECAUSE YOU HAVE TO HAVE A LOT OF EXPENSIVE TOOLS AND HIGHLY SKILLED TO REBUILD ENGINE.ITS NOT A EASY JOB.

Oct 25, 2009 | 1995 Isuzu Rodeo

1 Answer

Hollow bolt torque and oil presser warning light


torque it to 65% of the maximum torque rating for that diameter bolt

Jun 25, 2009 | 1998 Subaru Legacy

3 Answers

Oil light, noisy engine


If engine is noisy then you have an actual oil pressure concern.Sending unit only reads the pressure. I would recommend you have an actual oil pressure test done to see what your oil pressure is.You didn't mention what engine you have but rule of thumb is 30 psi at 1500 rpm warm engine.

Feb 06, 2009 | 2001 Ford Escape

Not finding what you are looking for?
2006 Nissan Murano Logo

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...