Question about 1989 Honda CRX

1 Answer

Turn signals won't work and ignition busser won't stop

I already tried replacing the flasher and the turn signals won't work they stopped working the same time the ignition buss started going off all the time. The car does have a viper alarm system on it, but it is in valet mode. My car is a 1988 CRX with a swap out moter to a 1998 integra 1.8. but until now it ran fine and everything worked.
Thank you, any suggestions would be appreciated.
Hollie

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 137 Answers

See if the 4 way (hazard) lights work. if they do then you may have bad turn signal switch or something in that switch, power or ground, is not getting where it needs to go. most manufacturers call that part a multifunction switch because it controls turn signals, headlights, usually some other stuff too. you should make sure you don't have a blown fuse in your turn signal circuit too. not sure i know what the ignition buss is. hope this helps

Posted on May 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The turning signals on a 2000 Dodge Durango stopped working I already changed the sensors, the 15a and the flasher unit/relay,and the multifunction. The emergency lights work. What else should i do?


If the flasher unit as well as the multi function switch have been replaced with KNOWN good parts and the fuse is good, chances are a power or ground problem in the circuit. The signals may have an additional ignition power source from the battery junction box under the hood. Check all the fuses there as well. IF all fuses ok, electrical diagnostics will need to be performed to isolate the bad circuit

Dec 29, 2015 | Cars & Trucks

1 Answer

Can a turn signel work for about 15 seconds and then stop? or could it be the relay?


the flasher unit is probably worn out.there is a bi-metalic metal strip that gets tired and won`t expand and contract making the clicking noise you hear when the signals are in use.it stops expanding and contracting causing the flashers to stop working.change the flasher unit but make sure you changing the one for the signal flasher and not the hazards flasher as they look the same.to know which one turn on the hazards and look for the other flasher that is not making a noise as this will be the one for the signals.

Mar 02, 2012 | Cars & Trucks

1 Answer

I have a 2002 honda accord when I push on the brake padel my turn signals or my 4 way flashers won't work. When I put on my lights my turn signals or my 4 way flashers won't work. Could you please...


Hi,
First check the fuse in the fuse box for signal light, replace the fuse with similar value if it is busted. If the fuse is still intact the problem would be the flasher relay( small cylindrical aluminum ) that is already malfunctioning.

Hope that helps you out!

Aug 07, 2011 | 2002 Honda Accord

1 Answer

2000 Intrepid turn signals stopped working, I replace the flasher relay, still turn signals not working?


did you replace the turn signal flasher or the emergency flasher? turn on the emergency flasher lights and pull that flasher if they quit working you changed the wrong one.

Jun 25, 2009 | 2000 Dodge Intrepid

2 Answers

Turn signals and emergency flashers stopped


they are under the dash, but its highly unlikly that both would go bad at the same timeyour promlem is probly in the steering colum

Mar 05, 2009 | 1997 Mercury Sable

1 Answer

1996 Jeep Cherokee Turn Signals Not Working


Replace you turn signal flasher relay, it should be right by your fuse box or near the brake pedal.(it looks like a solenoid, a cylindrical shape, with 3 prongs on the end) it is attached to a wiring harness that you just have to unplug it from. i couldnt find mine at any auto parts store, had to go to jeep, costs 44 bucks. that should do it

Feb 27, 2009 | 1996 Jeep Cherokee Sport

1 Answer

Signal lights and brake lights stopped working


the multifunction switch (turn signal switch) is a major cuase of this. your high mount stop lamp wire is run through the switch.

Dec 21, 2008 | 2000 Ford F150 Flareside SuperCab

3 Answers

Turn signals


replaced turn signal flashers and muti switch turn signal still won't work Why?

Nov 08, 2008 | 2000 Jeep Grand Cherokee

3 Answers

Blinkers stopped working


Your F--150 has 2 flashers, emergency and turn signal. Both are mounted on the fuse block under the dash. The turn signal flasher is mounted on the front of the fuse panel, the emergency flasher is mounted on the rear of the fuse panel. so replace the turn signal flasher should solve the problem. Let me know how it goes.

Oct 20, 2008 | 1996 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...