Question about Nissan Cars & Trucks

1 Answer

Crank angle sensor location

I was wondering where the crank angle sensor is located in the x-trail 2003 model

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

The crank sensor is always located next to the crankshaft pulley. it will be inserted into the block with the top part of the housing half way out. you cant miss the wires leading into the tip of the housing next to the crank shaft pulley.

Posted on May 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find the crank sensor on a 2009 Nissan Titan v8 truck?


i think it's the starter. On most nissans, the starter and the crank position sensor are close to each other. Some nissans have 4 position sensors, between crank sensor, crank angle sensor, cam position sensor, and sensor sensing sensor, oh and cam angle sensor. Oh wait, maybe it's a bad ground. Nope, gotta be the staerter.
25440212-xipalmoknr3fbjmp51kycajc-3-0.jpg

25440212-xipalmoknr3fbjmp51kycajc-3-1.jpg

Feb 17, 2015 | Nissan Cars & Trucks

1 Answer

Does a 2000 land rover freelander 1.8 xei have a camshaft position sensor or a crank angle sensor


Cam senso and crank sensor are at front of engine behind the grillto the right of centre looking at front of vehicle. this model has an inertia switch whichcuts fuel supply if you have had a decent bump recently.It is located on pass side strut tower. have you checked the immobiliser system? it has a deadlock or super immobiliser system. manual should tell you about this. wont hurt to check all fuses under bonnet and in passanger compartment.If all above are OK then you can check voltage at coilpak. orange wire is the voltage supply and the black with white trace is the pulse. good luck

Dec 10, 2012 | Land Rover Freelander Cars & Trucks

2 Answers

Need the wiring diagram for a 2003 nissan x-trail engine?


what is A color of wire in nissan x trail cam position sensor 2003 model

May 28, 2012 | Cars & Trucks

1 Answer

2006 2.5lt petrol X trail. Car is hard to start, can take up to 15 goes before it starts.have replaced both crank angle sensors


2003 nissan petrol xtrail stars some times other times just winds over
have changed crank and cam sensors reset ecu fitted new fuel pump still the same

Apr 26, 2012 | 2006 Nissan X-Trail 2.5

1 Answer

Location of cam and crank angle sensor in 96 N15


The cam and crank position sensor can be found in the front of the crank on the engine block below or next to the water pump in many applications.
It can also be located on the main crank pully or the flywheel.

Feb 09, 2012 | Nissan Pulsar Cars & Trucks

1 Answer

How do i replace the crank position sensor on a 2000 jeep grand cherokee


If you have the type of crank angle sensor shown in the image, then it will be located on the bell-housing towards the top of the bell-housing and usually on the drivers side. Dis-connect the faulty crank angle sensor and then un-bolt the two bolts that secure the crank angle sensor to the bell-housing and then remove the sensor. The best access to the crank angle sensor is from under the vehicle.


47ada7e.jpg

Jun 21, 2010 | 2000 Jeep Grand Cherokee

2 Answers

Ka24e locate the crank angle sensor


The sensor is located in the bottom inside of the distributor.

Jun 30, 2009 | 1997 Nissan Pickup

1 Answer

Jeep wrangelr Crank Position Sensor


wall5552: there were two engines used in 1992 Jeep Wranglers.
A 2.5 liter and a 4.0 liter. HOWEVER>>>> The location for the crank angle sensor is the same for both.
It is located on the bell housing up near the front at about the 10:00 PM position.
The Cam position sensor is located in the Distributor on both engines as well.

May 10, 2009 | 1992 Jeep Wrangler

1 Answer

Crank sensor location on Hyundai Sonata 2003 model


look carefully on bellhousing and rocker cover/head it has to be somewhere

Apr 03, 2009 | Hyundai Motor 2003 Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

2,275 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...