Question about 2005 Chevrolet Uplander

2 Answers

Where is the wiring harness connector for the service engine light located

Where is the wiring harness connector located for the service engine light on a 05 chevy uplander

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 79 Answers

Take the any front wheel off ,you will see the wiring right behind the disc brake,it is only one cable and the connector is right beside the hub,you see a short wire coming from inside the disc and the other side come from the upside of the hood where all the fuses are.

Posted on May 27, 2013

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 253 Answers

It is under the drivers side of the dash. Good Luck

Posted on May 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Solution for 1999 chevy cavalier code p0440


There has been a service bulletin isued for that code. I have run into this before, also the wires comming out of the connector. That would bethe first thing to check. Here is what the bulletin states. Emissions - SES Lamp ON/DTC P0440 (EVAP) SetNotesFile In Section: 06 - Engine/Propulsion SystemBulletin No.: 02-06-04-044Date: August, 2002TECHNICALSubject: Service Engine Soon (SES) Light Illuminated, DTC P0440 Set (Replace Fuel Tank Evaporative Emissions Control System (EVAP) Vent Solenoid Harness) Models: 2000-2002 Chevrolet Cavalier2000-2002 Pontiac Sunfire ConditionSome customers may comment that the SES light is/was illuminated.A technician may find DTC P0440 is stored in the PCM.CauseThe EVAP solenoid harness may be misrouted around the rear antilock brake (ABS) wire harness causing a chaff/damage to the EVAP vent solenoid harness, setting DTC P0440.CorrectionFollow the service procedure below to diagnose and correct this condition.1. Install a Tech 2 scan tool and select the appropriate vehicle. Verify that a DTC P0440 is stored in the PCM. 2. Raise the vehicle on a hoist. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID # XXXXX).

4_9_2012_3_31_41_pm.gif

Locate and inspect the EVAP vent solenoid harness (3) routing. The harness may be routed below the ABS wiring harness (4) at the right rear corner of the fuel tank, causing stress on the EVAP solenoid harness (3).



4_9_2012_3_32_10_pm.gif

4.Disconnect the EVAP vent solenoid harness (3) from the EVAP vent solenoid (2) and connector C313 (1). Discard the EVAP vent solenoid harness (3).


5.Connect the new EVAP vent solenoid harness (3), P/N 22687059, to the EVAP vent solenoid (2), route the harness above the rear ABS harness (4) and connect the EVAP vent solenoid harness (3) to connector C313 (1).


6.Lower the vehicle.


7.Clear the DTC's with the Tech 2 scan tool.



If all of the wires are good you will want to check for any leaks in the evap system.



Hope helps.

Apr 09, 2012 | 1999 Chevrolet Cavalier

1 Answer

Where is the starter located on my 2003 nissan sentra ser


Starter Motor -located to articulate with flywheel that has gear teeth between the engine and transmission accessible from down below. REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  3. Lightly lower the transmission to make room and pull out the dipstick tube.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  5. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
    • Negative battery cable
  6. Remove the transmission jack
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 70 inch lbs. (8 Nm)
    • Starter electrical connections
    • Negaative battery cable
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle

      Image 89612G12l Not Found

    To install:
  2. Install or connect the following:
    • Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) and the short bolt to 22-30 ft. lbs. (30-41 Nm)
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
Altima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Starter
    To install:
  2. Install or connect the following:
    • Starter and torque the bolts to 60 inch lbs. (7 Nm)
    • Starter electrical connectors
    • Harness bracket
    • Air inlet tube
    • Negative battery cable

Nov 03, 2010 | 2003 Nissan Sentra

1 Answer

How do i change the starter on a 2000 nissan altima


I hope this helps:

REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  4. Lightly lower the transmission to make room and pull out the dipstick tube.
  5. Remove or disconnect the following:
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  6. Install or connect the following:
    • Starter
    • Starter bolts. Tighten the bolts to 30–37 ft. lbs. (40–50 Nm).
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
  7. Remove the transmission jack
    • Negative battery cable
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter
    • Starter bolts. Tighten the bolts to 30–37 ft. lbs. (40–50 Nm).
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter from the vehicle
    To install:
  2. Install or connect the following:
  3. Install the components in the reverse order of removal.
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle Fig. 1: Starter location and mounting detail — Maxima with a manual transaxle 89612g12.gif
    To install:
  2. Install or connect the following:
    • Starter
    • Starter attaching bolts. Tighten the long bolt to 57–72 ft. lbs. (77–98 Nm) and the short bolt to 22–30 ft. lbs. (30–41 Nm).
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
  3. Start the engine a few times to make sure of proper operation.
Altima
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter from the vehicle
    To install:
  2. Install the components in the reverse order of removal.
prev.gif next.gif

Jul 13, 2010 | 2000 Nissan Altima

1 Answer

I replace the fan clutch and i still have the code p1481 what does that mean? 2002 chevrolet Trailblazer 4.2 Thanks You! Arthur Tyler


TSB#05-06-02-012B: Service Engine Soon (SES) or Check Engine Light On, DTC P0480, P0526/P1481/P1484 Set (Replace Engine Cooling Fan Wiring Harness) - (Oct 19, 2006)
Subject:
Service Engine Soon (SES) or Check Engine Light On,
DTC P0480/P0526/P1481/P1484 Set (Replace Engine Cooling Fan Wiring Harness)
Condition
Some customers may comment that the Service Engine Soon (SES) or Check Engine light is illuminated. This condition may be intermittent and upon investigation, the technician may find either DTC P0480, P0526, P1481 or P1484 set.

Cause
This condition may be caused by the cooling fan harness chaffing against the plastic guide it routes through. This
contact may damage the insulation of the wires enclosed in that harness.

Correction
Replace the engine cooling fan harness using the procedure listed below.

1. Remove the cooling fan. Refer to the Cooling Fan and Shroud Replacement procedure in the Engine Cooling sub-section of SI.

2. Place the cooling fan assembly on a bench.
Disconnect the harness electrical connector from the cooling fan clutch.

3. Remove the harness from the plastic guide while feeding the wires out of the slot.

4. Before installing the new harness, wrap the affected area on the wires with electrical tape to keep the protective sleeve in place. Be sure to keep the tape approximately 25 mm (1 in) away from the connector so the wires can be fed into the slot.

5. Feed the wires into the slot and install the harness to the plastic guide.

6. Connect the harness electrical connector to the cooling fan clutch.

7. Install the cooling fan. Refer to the Cooling Fan and Shroud Replacement procedure in the Engine Cooling sub-section of SI.

Part Number 89024920

Description
Harness Assembly, Engine Cooling Fan Wiring
Thank you for using fixya.

Apr 29, 2010 | 2003 Chevrolet TrailBlazer

1 Answer

How do you remove a 1999 Nissan Altima starter?


Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation
  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Apr 05, 2010 | 1999 Nissan Altima

1 Answer

1998 buick park ave. rear window defroster not working. fuse is good, has anyone replaced the black box located next to rear window where element plugs into along with the antenna. element on window is not...


Rear Defogger Inoperative, But Heated Mirrors Operate Correctly
1. Connect scan tool. Turn ignition switch to RUN position. Turn rear defogger on. Using scan tool, display BCM
outputs. If rear defogger is being requested on, go to next step. If rear defogger is not being requested on, go to
step 10).
2. Ensure ignition switch is in RUN position. Remove rear defogger relay from rear junction block, located on center
right rear of passenger compartment, under rear seat. Connect test light between ground and defogger relay
harness connector terminal F3 (Brown wire). If test light illuminates, go to next step. If test light does not
illuminate, go to step 11).
3. Connect test light between ground and defogger relay harness connector terminal A2 (Red wire). If test light
illuminates, go to next step. If test light does not illuminate, go to step 12).
4. Connect test light between defogger relay harness connector terminals A2 (Red wire) and B3 (Purple wire). If test
light illuminates, go to step 13). If light does not illuminate, go to next step.
5. Disconnect rear defogger positive and negative feed bus connectors. Connect a jumper wire between defogger
relay harness connector terminals F3 (Brown wire) and A4 (White wire). Connect test light between ground and
positive feed bus connector terminal "A" (Black wire). If test light illuminates, go to next step. If test light does not
illuminate, go to step 8).
6. Connect test light between positive feed bus connector terminal "A" (Black wire) and negative feed bus connector
terminal "B" (Black wire). If test light illuminates, go to next step. If test light does not illuminate, go to step 9).
7. Repair open in Black wire between rear defogger and ground. Recheck system operation.
8. Repair open in Purple wire between rear junction block and heated backlight antenna module. Recheck system
operation.
9. Check for proper terminal contact at rear defogger connectors. Repair as necessary. Recheck system operation.
10. Check for proper terminal contact at BCM. If terminal contact is okay, replace BCM. Recheck system operation.
11. Repair open in Brown wire between rear junction block and instrument panel junction block. Recheck system
operation.
12. Repair open in Red wire between rear junction block and underhood junction block (located in right front corner of
engine compartment, between battery and strut tower). Recheck system operation.
13. Connect test light between defogger relay harness connector terminals F3 (Brown wire) and A4 (White wire). If
test light illuminates, go to next step. If test light does not illuminate, go to step 16).
14. Reinstall defogger relay. Disconnect BCM 32-pin Pink connector C2. BCM is located behind right side of instrument
panel, near rear of glove box. Using DVOM, check voltage between ground and BCM harness connector C2
terminal A3 (White wire). If any voltage is present, go to next step. If no voltage is present, go to step 17).
15. Repair open or short to ground in White wire between rear junction block and BCM. Recheck system operation.
16. Check for poor connection at defogger relay terminals. If connections are okay, replace defogger relay. Recheck
system operation.
17. Check for proper terminal contact at BCM. If terminal contact is okay, replace BCM. Recheck system operation.

Feb 25, 2010 | 1998 Buick Park Avenue

1 Answer

What color is the power wire in 1994 toyota pick up


this might help
1994 Toyota Pickup Car Security Wiring Diagram
Battery Constant 12v+ Positive Wire (+): White And White/Red
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness
Starter Positive Wire (+): Black
Starter Positive Wire Location: Ignition Switch Harness
Ignition Positive Wire (+): Black/Yellow
Ignition Positive Wire Location: Ignition Switch Harness
Second Ignition Positive Wire (+): Black/Yellow Or Black/Red
Second Ignition Positive Wire Location: Ignition Switch Harness
Accessory Positive Wire (+): Blue/Red
Accessory Positive Wire Location: Ignition Switch Harness
Parking Light Negative Wire (-): Red/Black
Parking Light Negative Wire Location: At Steering Column Harness
Parking Light Positive Wire (+): Green
Parking Light Positive Wire Location: In Drivers Kick Panel
Power Door Lock Negative Wire (-): Blue/White
Power Door Lock Negative Wire Location: At Door Control Relay. The door control relay, is located behind the driver dash speaker.
Power Door Unlock Negative Wire (-): Blue/Yellow
Power Door Unlock Negative Wire Location: At Door Control Relay. The door control relay, is located behind the driver dash speaker.
Door Trigger Negative Wire (-): Black/White Or Black
Door Trigger Negative Wire Location: At 2-Pin Plug, Top Of Fusebox
Domelight Supervision Wire: Use Door Trigger, Requires Relay
Domelight Supervision Wire Location: N/A
Horn Negative Wire (-): Green/Red
Horn Negative Wire Location: At Steering Column Harness
Tachometer Wire Negative Wire (-): Black
Tachometer Wire Negative Wire Location: At Diagnostic Connector. The diagnostic connector, is located on the passenger inner fender near the fuse/relay box.
Brake Light Positive Wire (+): Green/White
Brake Light Positive Wire Location: At Switch Above Brake Pedal
Factory Alarm Disarm Wire (-): N/A
Factory Alarm Disarm Wire Location: N/A
Factory Anti-Theft System: N/A
Factory Anti-Theft System Location: N/A

Nov 29, 2009 | 1994 Toyota Pickup

1 Answer

How to Replace a Heater Core


Removal & Installation

  1. Disconnect the negative battery cable.
    CAUTION After disconnecting the negative battery cable, wait 2 minutes for the driver-s/passenger-s air bag system capacitor to discharge before attempting to do any work around the steering column or instrument
  2. On diesel models, remove the passenger side battery and battery tray.
  3. Remove the instrument panel by performing the following procedures:
    1. Remove the air bag control module (ACM) and bracket from the floor panel tunnel.
    2. Remove the trim from both cowl side inner panels.
    3. Remove the steering column-to-instrument panel opening cover.
    4. Remove the 2 hood latch release handle-to-instrument panel lower reinforcement screws and lower the handle to the floor.
    5. Disconnect the driver-s side air bag module wiring harness connector from the lower instrument panel reinforcement.
    6. Place the wheels in the straight-ahead position and lock the steering wheel. Remove the steering column without disassembling it.
    7. From under the driver-s side of the instrument, disconnect or remove the following items:

      Parking brake release handle linkage rod from the parking brake mechanism located on the left cowl side inner panel. Instrument panel wiring harness connector from the parking brake switch located on the parking brake mechanism. Three wiring harness connectors (body wiring harness, headlight, dash) from the 3 junction block connector receptacles located closest to the dash panel. Head light/dash-to-instrument panel bulkhead wiring harness connector screw and disconnect the connector. Instrument panel-to-door wiring harness connector located directly below the bulkhead wiring harness connector. Infinity sound system wiring harness connector (if equipped), located at the outboard side of the instrument panel bulkhead connector. Stop light switch electrical connector. Vacuum harness connector located near the left side of the heater/air conditioning housing.
    8. Under the passenger-s side of the instrument panel, disconnect the radio antenna coaxial cable connector.
    9. Loosen both sides of the instrument panel cowl side roll-down bracket screws about 1 / 2 inch (13mm).
    10. Remove the 5 upper instrument panel-to-upper dash panel screws; remove the center screw last.
    11. Roll down the instrument panel and install a temporary hook in the center hole on top of the panel. Attach the other end to the center hole in the top of the dash panel. The opening should be approximately 18 inches (46cm).
    12. Disconnect the instrument panel-to-heater/air conditioning housing assembly wiring harness connectors.
    13. Using an assistant, remove the instrument panel from the vehicle.

  4. If equipped with air conditioning, perform the following procedure:
    1. Discharge and recover the air conditioning system refrigerant.
    2. Disconnect the refrigerant lines from the evaporator. Plug the openings to prevent contamination.
    3. Disconnect the refrigerant lines from the accumulator. Plug the openings to prevent contamination.
    4. Remove the accumulator.

  5. Drain the cooling system into a clean container for reuse.
  6. Disconnect the heater hoses from the heater core tubes.
  7. Remove the PCM from the dash panel and move it aside. Do not disconnect the PCM harness connector.
  8. In the engine compartment, remove the heater/air conditioning housing assembly-to-chassis nuts.
  9. In the passenger-s compartment, remove the heater/air conditioning housing-to-dash panel nuts.
  10. Pull the heater/air conditioning housing assembly rearward far enough to clear the studs and air conditioning drain tube holes.
  11. Remove the heater/air conditioning housing assembly from the vehicle.
  12. Remove the upper-to-lower heater/air conditioning housing screws and remove the upper housing.
  13. Remove the heater core from the lower housing.


    Fig. View of the heater/air conditioning housing assembly


    0900c15280225dc3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. View of the heater core

Apr 07, 2009 | 1997 Dodge Ram

1 Answer

Service engine light on


To Install:
CAUTION
Do not tamper with the MAF sensing elements located in the airflow bypass; tampering may result in unit failure.
The grommet used to seal the engine air cleaner housing at the extension harness must be fully seated. Failure to do so will result in unmetered air entering the engine.
NOTE: Use the alignment notch to properly align the inlet side and the outlet side of the engine air cleaner.
NOTE: The MAF sensor module and body are calibrated and replaced as a unit.
  1. Install or connect the following:
    • The MAF plate to the MAF sensor
    • The MAF plate nuts
      1. Torque to: 89 inch-lbs (10 Nm)
    • The MAF sensor electrical connector
    • The MAF sensor to the outlet side of the engine air cleaner
    • The grommet to the outlet side of the air cleaner and slide the grommet up the extension harness
    • The wire loom to the extension harness near the grommet in the air cleaner
    • The tape on the wire loom of the extension harness
    • The inlet side of the air cleaner to the outlet side of the air cleaner
    • The air cleaner clamp
    • The Mass Air Flow (MAF) sensor connector to the wiring harness
    • The negative battery cable

Apr 04, 2009 | 2002 Ford F150 Regular Cab

Not finding what you are looking for?
2005 Chevrolet Uplander Logo

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...