Question about 2005 Ford F 350 Super Duty

1 Answer

Running problem sometimes at stop light rpm move up and down truck will riv up and down and take a second to take off at light or will crank over but wont start up until you cycle keyon and offmany time then it may run perfect for a week

Posted by on

  • Dennis Saunders
    Dennis Saunders May 11, 2010

    is this a gas or diesel?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Sounds like a MAP sensor.

Posted on May 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My air is not all that cold and when I am stop at a red light it blows warm air it has plenty of Freon in it. What could it be?


If the air is cold when the vehicle is moving and goes warm when stopped,the fan at the rad/condenser may not be working,or working but not running fast enough.Sometimes there may be a second fan that comes on also.If the fan/fans are running and you can get cold air at a stop by increasing rpm then the system may be low on refrigerant.

Jul 09, 2017 | Cars & Trucks

1 Answer

Engine cranks, runs for 1 or 2 seconds and then stops.


Two items to check. The crankshaft sensor will reduce fuel pump pressure if it miscounts the RPM. The plastic strainer in the fuel tank can break apart and clog the pump intake in the tank. When the engine quits, the fuel pump is stopped and the loose particles are returned to the tank bottom.

In either case, try checking the fuel pressure at the test tap on the fuelrail.

Feb 03, 2014 | Ford Crown Victoria Cars & Trucks

1 Answer

My 1994 Nissan Quest engine starts up properly and idles when cold. After the engine has been running for a while the idle is a little off every time I stop at a light or when it gets to about 1500 rpm....


Looks like you have a wire harness problem check your harness around the engine and see if there is any broken or making contact specially with the exhaust manifold also check you crank sensor and your fuel pump, because something is getting overheating.
Good luck.

Jan 01, 2014 | Cars & Trucks

1 Answer

I have a 1971 f100 with a 360 engine and a motorcraft carb. my truck is not running right at all and i cant figure out why. when i turn over the engine its acts like it will go then it stops and then...


Sounds like it might be out of time. Check with a timing light. Don't know what the specs are, move the distributor until it cranks smooth and easy. Then check timing when running.

Aug 23, 2013 | Ford Cars & Trucks

1 Answer

2000 mercury cougar engine speed stays up when gas pedal is release, increase when pedal is release and shifting gears, takes 3 seconds or more to come down to idle when gas pedal is release, will hold at...


You have a mechanical bind. Disconnect the main linkage and work it all by hand. Everything should be free and slopy. Aerosol carb cleaner will help, but only when the engine is not running.

May 30, 2017 | Mercury Cougar Cars & Trucks

1 Answer

While driving my 1993 929 down the road it just stopped running...had it checked out was told ti would be best to get a new motor and got a second opinion and was told to get a timing belt and fuel pump....


before going crazy , check the crank sensor out, a bad crank sensor will cause timing to be out of sync. more then likely engine will not start. or irregular rpm function if vehicle starts at all. it controls timing and sends info to pcm. if a crank sensor fails while driving the engine will die out. have scanned if check engine light is on. CPS symtoms are: car dies and won't re-start till it cools down, or won't start at all.
first of all, if crank sensor is ok, then you can check the timing belt.

Aug 24, 2010 | 1993 Mazda 929

1 Answer

RPM rev up and down at idle/ backfires/


Dont have the time right now to outline all the details, but I will bet that the timing chain is worn 4.0 engine?? Also I'd guess the problem started at about 160-170k miles.(how close am I???)

Jan 16, 2009 | 1998 Jeep Cherokee

1 Answer

Rough idle stalls at low rpm's


hello first check your idle with the car running foot on brake see were your rpm reading is if your below 500rpm check your label underhood for your curb idle setting second see if theres a adjustment screw you can increase were your gas cable lever rest against your set screw underhood if you feel confident enough remove your iac motor idle air control valve if the bore were the end of the pintle extracts out to close has varnish builup our carbon it will stick creating vacuum leak type senario causing stalling rough idle sometimes even no start conditions good luck

Sep 14, 2008 | 1988 Honda Accord 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...