Question about 1998 Jeep Cherokee

1 Answer

Power window off the track, i think

I have removed all the screws and can't seem to get the door panel off to work on it. when i apply alot of pressure with a screw drive to pry it off it won't budge. i am affraid to break something......help

Posted by on

  • mmoore602 May 22, 2009

    i will try it, thanks!!! and God Bless!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

If you have all the screws out, lift the panel straight UP. It should come loose.

Posted on May 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i get it back on track


remove innder door panel and carefully put it back on track

Jun 08, 2015 | 1993 Chrysler Imperial

1 Answer

My 2008 chevy impala power window on the driver side will not raise. When you depress the switch, it tries to work. But when you try to raise the window, the switch seems to have no power. What can


z

General instructions for door panel removal; Door panels are attached to the door frame with clips such as the one above. The ribbed, screw-like part of the clips are inserted into holes in the door frame around the perimeter of the sides and bottom of the panel
Auto Repair Mechanics How to Remove Car Door Panel

The video shows details of door panel removal. First locate all the screws on the door panel, usually at the door handle and door rest. Look for any hidden screws that may be covered with small plastic caps.

After all screws are removed, the side and bottom clips need to be popped out of the door frame. You can purchase a set of trim tools to pop the clips, or you can use flat blade screw drivers and a flat putty knife to pop the clips out. Sometimes the clips break, but they are replaceable. Once the sides and bottom are loose, the top of the panel is loosened by lifting up on the panel, disengaging the panel from the top track on the door frame. Be careful of wiring connectors, which will have to be disconnected to completely remove the panel.

May 26, 2014 | 2008 Chevrolet Impala

2 Answers

Rear door panel removal:rear door window just fell down oneday and i was told it might just be off the track. it has electric windows


Its not off the track!!
You just lost the holders clipping your window glass piece.
  • Look for screws in door panel or around the speaker vents.
  • If you are sure that the speaker cant be removed without opening the door panel then read this below.
  • Mostly seen near areas like door lever(inside), power window switch set, bottom and each sides of the whole panel.
  • If its manual window, then look for a circle clip in between the winding window lever and the door panel. Plunge screw driver between them a make a gap then look.
  • Assure that all clips or screws which obstacles the removal of the panel.
  • Simply pull the panel from sides towards you

Sep 23, 2011 | 2007 Chevrolet Malibu SS Sedan New Cars

1 Answer

How do you get the driver's door latch out past the window guide?


Remove all screws around the outer edge of the door panel. Carefully pry off the decorative cover behind the door handle and remove the torix screw. Lift up firmly on the door panel to remove. To reinstall, line up molded plastic hooks on back of door panel with notches in the door, push down to secure, reinstall torix screw, decorative cover and screws.
Also before you lift away the panel, you'll need to undo the electrical connectors for the power window and door locks

It is best to get the whole power window regulator assembly from the junkyard, which includes the power window motor. Cost should be no more than $40. Remove interior door trim panel by removing all screws and pulling up on the door panel. Unbolt existing window regulator assembly and slide guides from aluminum window track (you will have to uncrimp one end of track). Installation is the reverse of removal (remember to recrimp aluminum window track after reassembly). I did this repair in 45 minutes, power window worked like new. Good Luck!



Dec 12, 2010 | 1996 Chevrolet Monte Carlo

1 Answer

The drivers side rear window does not work. It does side down, and when the power switch is press the motor turns on. could the window be off its track or does the window unit need replaced?


It sounds like the window may be off its track. All that needs to be done is to remove the inner door panel. Be careful to pry the clips very gently. They break easily. However, most auto parts stores carry replacements. Once the door panel is off, remove the plastic sheeting that covers the door frame. It's attached with a mastic adhesive.
Once you have a clear view of the window rail, carefully pull the pane up and set the glass on the track. You may need to apply some silicone in the track to keep the glass in place.

Then, test the alignment by pressing the power button and roll the window up and down. With the window closed, replace the plastic sheeting and the door panel.

That should do it.

Oct 09, 2009 | 1994 Lincoln Town Car

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

2 Answers

Cable fell off track


You will need to Remove the Door Panel. Look for Screws and Screw Hole Covers first. Start at the Bottom of the Panel and work your way up. There are Holes in the Door Behind this that will allow Access to the Window and Components. Just look and see if the Glass is Off Track. If it is Use Clear Silicone and Reinsert the Glass. Roll it up all the Way and wait 24 hour or more for it to Dry before you roll it down again. If it is a Belt or something, You will be able to see it. If it is gone, Reach down inside the Door at the Bottom and Locate it.

Jan 23, 2009 | 2004 Jeep Liberty

1 Answer

The front driver side door on my 00 expedition


alot of cars and mount door panels the same ways . if look were fingers grab the door to close it and were arm rests you will see small plastic plugs remove the plugs and you will see screws remove the screws. also were the widow swicth is remove and look behind it . also open door all up and look in door jam for other fasteners when all screws are removed then trie to pull at bottom of panel while pulling look between door and panel some cars pull out and some cars lift up . once u get loose then u lift up to remove from sill of door. then disconnect any electrical connectors. sounds like window linkage hitting door handle linkage inside the door.

Dec 02, 2008 | 2000 Ford Expedition

1 Answer

REMOVING A DOOR PANEL


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Oct 02, 2008 | 2002 Buick Rendezvous

Not finding what you are looking for?
1998 Jeep Cherokee Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...