Question about 2003 Kia Rio

1 Answer

Need instruction manual/schematics for replacing 2005 kia rio driver side rear wheel bearing. i've got the wheel/hub/bearing off, not the inside ring to the bearing. i need to know how to replace it .

Need instruction manual/schematics for replacing 2005 kia rio driver side rear wheel bearing. i've got the wheel/hub/bearing off, not the inside ring to the bearing. i need to know how to replace it .. as i do not know how ? because well the parts were all goulashed up inside the hub... thanks for your time and consideration. respectfully e.m.w.

Posted by on

  • 1 more comment 
  • neoracle May 22, 2009

    Thanks, the inner ring to the bearing is stuck on the axle, which we are trying to remove now, not the funnest thing ive done ,


    thanks again

    emw


  • neoracle May 22, 2009

    Thanks, the inner ring to the bearing is stuck on the axle, which we are trying to remove now, not the funnest thing ive done ,


    thanks again

    emw


  • Anonymous Mar 23, 2014

    How to replace carrier bearing on kia sorrento 2005

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 351 Answers

Clean all the grease if there is any out of the hub, turn the hub over and using a drift and hammer strike the shell from the back edge working around the shell as you go, should not take too much to remove it but you will need a bit more than a tap with the hammer.
Hope this has helped you

Posted on May 22, 2009

  • Harry Goodwin
    Harry Goodwin May 23, 2009

    try cutting the shell with a small grinder if it will fit or heat the shell with an oxy torch to expand it and give it a tap while it is hot, does not need to be red hot but just enough to expand

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How can I remove rear outer bearing?


New style bearings are all pressfit bearings, if your hub came right out of the bearing assembly, it is time for the whole assembly. The hub assembly has a locking ring that holds the outer bearing race inside the hub, after the wheel hub has been pressed out. Then, after the lockring has been removed it can be pressed out and the new bearing can be pressed back in and then the lockring reinserted. Then the wheel hub gets pressed in.

Mar 05, 2016 | 2002 Kia Sportage

1 Answer

What is the 2005 kia rio front axel nut torque ???


Hi,
for the front hub its 157 - 235 Nm.

Sep 20, 2014 | 2005 Kia Rio

1 Answer

How to remove a front wheel bearing on a 2001 kia rio


Does 2001 kia rio need to have a spacer for the driver side wheel bearings

Aug 25, 2012 | 2001 Kia Rio

2 Answers

Grinding noise from rear and rear brack hub hot


Collapsed rear wheel bearing or worn brake shoes or pads. You will need to pull the wheel and hug off to check both.

Jan 16, 2011 | 2002 Kia Rio

1 Answer

Need help replacing front hub


Here's the steps....getting some pics for you....hang on a minute or two.

Front Hub Removal & Installation To Remove:
  1. Remove steering knuckle.
  2. Using a suitable slap hammer, remove wheel hub assembly.
  3. Using a suitable bearing press, remove outer bearing, oil seal, outer bearing race and preload spacer.
  4. Remove inner oil seal, inner wheel bearing and inner bearing race.
NOTE: It is not necessary to remove dust cover (back plate).
To Install:
  1. Using a suitable bearing press, install bearing races in steering knuckle.
  2. Pack the bearings and hub area with lithium grease.
  3. Install inner bearing in steering knuckle.
  4. Lubricate lip of NEW inner seal and press seal into knuckle.
  5. Install preload spacer into bore.
  6. Install outer bearing into bore.
  7. Lubricate lip of NEW outer seal and press seal into knuckle.
  8. Using an appropriate tool, support inner wheel bearing and press wheel hub into knuckle with a force of 2500kg.
  9. Install NEW inner seal.
  10. Install knuckle assembly.

May 13, 2009 | 2004 Kia Rio

1 Answer

Need to replace a rear wheel bearing, can't even get the hub off!!!


pull off rim. there is a cap in the center of the hub that you will have to tap/pry out with a screwdriver, then remove bolt and slide hub off.
thats how i fixed mine.

May 06, 2009 | 2004 Kia Rio

5 Answers

Kia Rio Wheel Bearing ( replaced mulitple times )


it is actually caused by a bad spindle. this happened to my best friend numerous times also. if the spindle is not replaced when the bearings are it will just keep happening.

Dec 28, 2008 | 2003 Kia Rio

5 Answers

2002 Kia Rio rear wheel bearing passenger side


I'm from the United States, East coast.

Nov 24, 2008 | 2003 Kia Rio

Not finding what you are looking for?
2003 Kia Rio Logo

767 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

yadayada
yadayada

Level 3 Expert

77194 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...