SOURCE: help stuck n storm..where is fusebox 2004 murano windshieldwipers
There's no need to remove the fuse to change wiper blades.
If there are electrical problems the fuse locations are driver's bottom left near steering wheel, and under the hood. Under the hood is the ipdm located on the passenger side near the alternator. More fuses can be found beside the battery.
If your wiper motor runs but wipers don't move, the linkage is disconnected.
SOURCE: Diagram of 1996 ford ranger fusebox which fuse is
RANGER FUSE PANEL
Fuse Position
Rating
Circuit Protected
1
7.5 Amp
Power Mirror
2
—
Not Used
3
15 Amp
Parking Lamps
4
10 Amp
Left Headlamp
5
10 Amp
On Board Diagnostic (OBD) II System
6
7.5 Amp
Air Bag System/Blower Relay
7
7.5 Amp
Illumination Switches
8
10 Amp
Right Headlamp/Fog Lamp System
9
10 Amp
ABS System
10
7.5 Amp
Speed Control/GEM System/Brake Interlock
11
7.5 Amp
Warning Lamps
12
10 Amp
Front Washer System
13
15 Amp
PCM System/Stoplamps/
4WD/ABS/Speed Control
14
10/20 Amp
ABS System
15
7.5 Amp
Air Bag System/Alternator
16
30 Amp
Front Wiper
17
15 Amp
Cigar Lighter
18
15 Amp
A/C System
19
25 Amp
Ignition Coil/PCM System
20
7.5 Amp
Radio/GEM System/Anti-Theft
21
15 Amp
Hazard Lamps
22
10 Amp
Turn Signals
23
—
Not Used
24
10 Amp
Starter Relay/Anti-Theft
25
7.5 Amp
Speedometer/GEM System
26
10 Amp
4R44E/4R55E Trans./Backup Lamps/DRL System
27
10 Amp
Underhood LP/Map Lights/Glove Box Lamp/Dome Lamp/Visor Lamps/4x4 Sys.
28
7.5 Amp
GEM System
29
10 Amp
Audio System
30
—
Not Used
31
—
Not Used
32
—
Not Used
33
15 Amp
High Beam Lamps
34
—
Not Used
SOURCE: Where can i find a
as the rear parking sensors are hardwired into the reversing light circuit/switch,they will not be shown on the wiring diagram/fuse panel.check your reversing lights.......as a starting point....
SOURCE: i dont have brakelights and
Climb under the driver's side of the dashboard with a flashlight and box wrench set. Shine the flashlight on the Windstar's brake pedal arm to illuminate the brake switch. Unplug the brake light circuit connector from the brake switch. Unbolt the Windstar's brake switch from its mounting bracket with the box wrench set. Bolt the Windstar's replacement brake switch onto the bracket with the box wrench set. Plug the brake light circuit connector into the brake switch
Read more: How Do I Change the Brake Switch on a 1996 Ford Windstar? ' eHow.com http://www.ehow.com/how_7624548_do-switch-1996-ford-windstar.html#ixzz1CSAaHtlA
SOURCE: how do i program my ford key fob 2 my transit van
1 - Unlock the doors. Put the key in the ignition, and turn from "Off" to "ACC" 8 (eight) times in under 10 seconds. The doors will lock. Leave key in the "ON" position
2 - Program the fobs by pressing any key on the fob. The doors locks will lock/unlock
3 -- Turn the key to Off. Locks will lock/unlock, and you are out of programming mode.
I bought new remote Key Fob on Ebay and it did work properly on my Ford Transit LWB 2003. Good Luck!
30 views
Usually answered in minutes!
×