Question about Mazda 626

1 Answer

2002 mazda 626 fuel pump issue

I did a fuel pressure test and I wasn't holding fuel pressure, I replaced the fuel pump but now the car doesn't turn on. I got power to the relay but when I test the pump connector I get no power

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 3,103 Answers

Try the fuse or reset button in the trunk..drivers side black and yellow tag on it..

Posted on Jan 04, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76848 Answers

SOURCE: Location under hood for fuel pump relay on 2002 Mazda Millenia S

JUST RELEASE THE PRESSURE AT THE FUEL PRESSURE TEST PORT ON THE FUEL SUPPLY RAIL THAT SUPPLIES THE INJECTORS, IT IS A METAL VALVE LIKE A TIRE VALVE, THAT IS THE FACTORY RECOMMENDED METHOD..

Posted on Mar 11, 2009

rcampsr
  • 90 Answers

SOURCE: Do you know where or if a 2000 Mazda 626 has a

Hello, I am going to make a few assumptions here. The vehicle has an electric fuel pump and you replaced it. The vehicle has fuel injection. The engine is actually cranking, just not starting, when you say "car still won't crank". You are getting fire to the spark plugs at the plug ends. You checked the fuel pump for power at the pump. No power, then you back traced the wire to the fuse block and checked the fuse to see if it was blown. If the fuse is good back trace the power to the ignition switch and/or ECM for power. You have power at the pump, check the ground and make sure it is connected properly. Will the pump run when someone turns the key on? Pump runs, check fuel manifold for pressure. No pressure, check the fuel filter for blockage, or replace it. Fuel pump doesn't run, new replacement pump is defective. There is usually some type of control module for the fuel pump on fuel injected vehicles. Good Luck, RAC

Posted on Apr 18, 2009

localwonder
  • 6784 Answers

SOURCE: how do i replace the fuel pump in my 1993 mazda 626 2.5

1. Relieve the fuel pressure and disconnect the negative battery cable.

2. If not already removed, depress the clips on each end of the rear seat cushion and remove the cushion.

3. If not already done, detach the electrical connector from the fuel pump/sending unit.

4. Remove the attaching screws from the fuel pump/sending unit access cover and remove the cover.

5. Disconnect the fuel supply and return hoses from the fuel pump/sending unit.

6. Remove the attaching screws and the fuel pump/sending unit from the fuel tank.

7. Detach the sending unit electrical connector, remove the sending unit attaching nuts and remove the sending unit from the fuel pump assembly.



To install:

1. Attach the sending unit to the fuel pump assembly and install the nuts. attach the sending unit electrical connector.

2. Install the fuel pump/sending unit into the fuel tank with a new gasket and install the mounting screws.

3. Connect the fuel supply and return lines.

4. Install the access cover and the mounting screws.

5. Attach the sending unit electrical connector.

6. Position the rear seat cushion over the floor, making sure to align the retaining pins with the clips. Push down firmly until the two retaining pins are locked into the rear seat retaining clips.

7. Connect the negative battery cable, start the engine and check for proper system operation and for fuel leaks.

Posted on Jun 13, 2009

  • 850 Answers

SOURCE: 2000 elantra no power to fuel pump.

could be a bad earth or [ground]
the power wire ma be brocken or have a loose or dirty connection
you neeed to trace it along its lenght to determine the fault!
so start at the pump & work back
Cheers rob

Posted on Jul 20, 2009

wracefans24
  • 1985 Answers

SOURCE: How to Replace a Fuel pump on a 2000 Mazda 626

yes it isn't that much if you buy them.they slide inside the coupler and release the line.

Posted on Dec 27, 2009

Testimonial: "Thank you didn't know if there was a tool for this."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Mazda 626


Sixteen year old car with only 40K miles must not be driven often, or sat for some time. I would suspect fuel system issue, such as bad pump, clogged filter, bad regulator or faulty injectors. Start by testing fuel pressure.

Jun 20, 2016 | 2000 Mazda 626

1 Answer

How donu bleed the fuel on a 2000 Mazda 626 lx 2.0


You don't bleed the fuel. You have a fuel pressure regulator on the fuel rail that does this for you. Turn the key on 3 or 4 times. this builds up pressure. Try to start the car. If it does start, check fuel pressure. Check to hear if the pump is coming on.

Jan 03, 2015 | 2000 Mazda 626

1 Answer

02 626 mazda overheat issue


if this is fitted with a viscous fan hub and not electric fans then replace the hub. do the normal compression test and coolant pressure test to check cooling system and head gaskets.

Dec 23, 2014 | 2002 Mazda 626

1 Answer

Mazda millenin 2002 is cutting off when you come to stop


WEAK FUEL PUMP OR FAULTY IDLE AIR CONTROL.CHECK FUEL PRESSURE SHOULD BE 39 - 48 PS FOR 2.3 ENGINE AND 30 - 36 PSI ON 2.5 ENGINES. HAVE YOUR IGNITION TIMING CHECKED.

Sep 17, 2010 | 2002 Mazda 626

1 Answer

Where is the gassline pump on the 2002 mazda 626


the fuel/gasoline pump is located inside the fuel tank, the fuel tank must be removed to replace the fuel pump.

Sep 14, 2010 | 2002 Mazda 626

1 Answer

1999 mazda 626 6cyl no fuel geting to onjectors


Priority Action Part Type Cause
1 Inspect Fuel Pump fuse - short to ground in fuel pump circuit
2 Inspect Fuel Filter Clogged or Dirty Fuel Filter.
3 Inspect Relay - Fuel Pump Faulty Fuel Pump Relay.
4 Inspect Fuel Injector Pressure Regulator Faulty Fuel Injector Pressure Regulator.
5 Inspect Fuel Pump Low Fuel Pressure.
6 Inspect Engine Control Computer Incorrect Operating Information Being Delivered and Sent From The EEC.
7 Inspect Fuel Pump Strainer Clogged or Dirty Fuel Pump Strainerat.
8 Inspect Fuel Rail - leaky Fuel Rail

From April 2010? What did the problem turn out to be?

Apr 25, 2010 | 1999 Mazda 626

1 Answer

My friend took out the motor on a 2002 mazda 626


first thing i'd check is that all the grounds are connected .if there is a bad ground or no ground you can send all the power you want and it still wont work.

Nov 19, 2009 | Mazda 626 Cars & Trucks

1 Answer

Fuel issue


fuel filter is between the tank and engine, usually under the hood. replace the fuel pump.

Sep 27, 2009 | 2000 Mazda 626

1 Answer

2001 mazda 626 4 cyl engine turns over, but won't start.Feels like it is not getting any gas.


See about getting a fuel pressure test. Or if your bold just go ahead and change the fuel filter. If both fail you might need a fuel pump

Jun 04, 2009 | 2001 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...