Question about 2007 Dodge Caliber SXT Sport Hatchback

Open Question

Primery sensors input and output on the cvt transmission are not receiving a signal

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: transmission is in limp mode

try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 20, 2009

nicole99wu
  • 1049 Answers

SOURCE: input output sensor transmission

hi, this is the diagram, hope helpful, greetings
12_8_2011_8_33_25_am.jpg

Posted on Dec 08, 2011

ZJLimited
  • 17970 Answers

SOURCE: 0700 codes after replacing speed sensors

Hi there:DTC P0700 is a generic warning code that advice about a transmission fault specific code stored there. In this case, your addicional specifi code is P0740.
DTC P0740 - Torque Converter Clutch control circuit (A/T Torque Converter Clutch - No RPM Drop At Lockup)

This can be caused from as little as a blown fuse or bad ground to a bad valve body in the transmission. I would suggest a transmission shop to further diagnose since there are pressures that need checked and circuits that will need checked with diagnostic equipment. Here is a description and the testing procedure for DTC P0740. Keep in mind that there is a good chance the trans will need rebuilt.



Possible Causes:

Internal transmission component fault (Input or Reaction shaft) Internal transmission leakage (valve body leaking or seal rings) Converter clutch valve or clutch timing valve is sticking TCC assembly has failed.



Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Jun 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can the input speed sensor on a 2009 GMC Acadia be changed without having to remove the transmission


Did you do the diagnostic's that go to that code ?
DTC P0717: Input Speed Sensor Circuit Low Voltage
Diagnostic Fault Information
Circuit
Short to Ground
Open/High Resistance
Short to Voltage
Signal Performance
Input Speed Sensor Supply Voltage
P0717
P0717
--
P0716
Input Speed Sensor Signal
P0716, P0717
P0716, P0717
P0716, P0717
P0716
Circuit/System Description
The input speed sensor (ISS) is a hall-effect type sensor. The sensor faces the 1-2-3-4 and 3-5-R clutch housing machined teeth surface. The sensor receives 8.3-9.3 volts on the input/output speed sensor (ISS/OSS) supply voltage circuit from the transmission control module (TCM). As the 1-2-3-4 and 3-5-R clutch housing rotates, the sensor produces a signal frequency based on the machined surface of the 1-2-3-4 and 3-5-R clutch housing. This signal is transmitted through the ISS signal circuit to the control solenoid (w/body and TCM) valve assembly. The control solenoid (w/body and TCM) valve assembly uses the ISS signal to determine line pressure, transmission shift patterns, torque converter clutch (TCC) slip speed and gear ratio.

Circuit/System Verification
Engine idling, observe the scan tool Transmission ISS parameter while varying the engine speed. The Transmission ISS parameter should change with the engine speed and not drop out.
Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Ignition OFF, remove the control valve body cover. Refer to Control Valve Body Cover Replacement.
Connect the TCM harness connector.
Disconnect the input speed sensor (ISS) from the control solenoid (w/body and TCM) valve assembly.
Connect the J 38522 between the supply voltage terminal B and ISS signal terminal A at the control solenoid (w/body and TCM) valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly Input Shaft Speed/Output Shaft Speed Input Test for further instructions.
Set the J 38522 signal to 8 volts, the frequency to 120 and the percent duty cycle to 50.
Ignition ON, observe the scan tool Transmission ISS parameter. The scan tool Transmission ISS parameter should be between 100-400 RPM.
? If not within the specified range, replace the control solenoid (w/body and TCM) valve assembly.
If all circuits test normal, test or replace the input speed sensor.

Control Valve Body Cover Replacement

Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement.
Remove the oil cooler inlet hose (1) from the retainer on the control valve body cover.
Remove the oil cooler outlet hose retainer nut (5) from the control valve body cover.
Remove the oil cooler outlet hose (4) from the retainer on the control valve body cover.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
Remove the left engine splash shield. Refer to Engine Splash Shield Replacement.
Drain the transmission. Refer to Transmission Fluid Replacement.

you don't need to pull thr trans .

Feb 19, 2017 | GMC Cars & Trucks

1 Answer

2007 3.5 dodge Dakota rpm sensor where is it located to replace


Not sure what you mean by rpm sensor. The signal for the tachometer comes from the PCM and is based on signals from the crankshaft position sensor, located on the right rear of the engine where the transmission bolts to the engine, but if this is bad, there are a lot more problems than the tachometer not working. There are two speed sensors on automatic transmissions, an input speed sensor and an output speed sensor. Both are located on the left side of the transmission, the input speed sensor near the front (just behind the bell shaped portion) and the output speed sensor near the rear. In addition to those there are wheel speed sensors for the ABS, located in each wheel area covered by the ABS.

Nov 13, 2016 | Dodge Dakota Cars & Trucks

2 Answers

Ok one major question! Will changing the tcc solenoid in my 01 cougar fix the o/d flashing and make the car go forward when I try to drive it?


No. replacing the TCC or the OSS, will not make the transmission work. You can unplug these transmissions and they will still work, less OD. Sounds like you may have stripped the torque converter oil pump gear. Common in these older Mercury/Fords.

Mar 18, 2016 | 2001 Mercury Cougar

2 Answers

Why my cvt lights in my dashboard on my 2004 Nissan murano


You need to have the transmission check for codes and operation concerns.

Feb 23, 2015 | 2004 Nissan Murano

2 Answers

Speed sensor


Speedometer sensor measures axle(driveshaft) speed for your speedometer gauge.
Input speed sensor measures the speed of the input shaft of the transmission.
The output speed sensor measures the output shaft, the ECM compares these two signals to determine the amount of clutch slippage and adjusts parameters accordingly for optimal operation.

Feb 02, 2014 | 2002 Kia Sedona

1 Answer

I need help asap 2003 Expedition code p0171 and code p0712 i have and idea of the 1st code but whats the secound code i really need help i dont want to take it to a shop where there going to charge me alot...


P0700 Transmission Control System

P0701 Transmission Control System Range/Performance

P0702 Transmission Control System -Electrical

P0703 Torque Converter/Brake Switch B Circuit

P0704 Clutch Pedal Position Switch -Circuit Malfunction

P0705 Transmission Range Sensor/Switch Circuit Malfunction (PRNDL Input)

P0706 Transmission Range Sensor/Switch Circuit Range/Performance

P0707 Transmission Range Sensor/Switch Circuit Low Input

P0708 Transmission Range Sensor/Switch Circuit High Input

P0709 Transmission Range Sensor/Switch Circuit intermittent

P0710 Transmission Fluid Temperature Sensor Circuit

P0711 Transmission Fluid Temperature Sensor Circuit Range/Performance

P0712 Transmission Fluid Temperature Sensor Circuit Low Input

P0713 Transmission Fluid Temperature Sensor Circuit High Input

P0714 Transmission Fluid Temperature Sensor Circuit Intermittent

P0715 Input/Turbine Speed Sensor Circuit

P0716 input/Turbine Speed Sensor Circuit Range/Performance

P0717 Input/Turbine Speed Sensor Circuit No Signal

P0718 Input/Turbine Speed Sensor Circuit Intermittent

P0719 Torque Converter/Brake Switch B Circuit Low

P0720 Output Shaft Speed Sensor Circuit

P0721 Output Shaft Speed Sensor Circuit Range/Performance

P0722 Output Shaft Speed Sensor Circuit No Signal

P0723 Output Shaft Speed Sensor Circuit Intermittent

P0724 Torque Converter/Brake Switch B Circuit High

P0725 Engine RPM Input Circuit

P0726 Engine RPM Input Circuit Range/Performance

P0727 Engine RPM Input Circuit No Signal

P0728 Engine RPM Input Circuit Intermittent

P0729 Gear 6 Incorrect Ratio

P0730 Incorrect Gear Ratio

P0731 Gear 1 Incorrect Ratio

P0732 Gear 2 Incorrect Ratio

P0733 Gear 3 Incorrect Ratio

P0734 Gear 4 Incorrect Ratio

P0735 Gear 5 Incorrect Ratio

P0736 Reverse Incorrect Ratio

P0737 TCM Engine Speed Output Circuit

P0738 TCM Engine Speed Output Circuit Low

P0739 TCM Engine Speed Output Circuit High

P0740 Torque Converter Clutch Solenoid Circuit

P0741 Torque Converter Clutch Solenoid Circuit Performance or Stuck Off

P0742 Torque Converter Clutch Solenoid Circuit Stuck On
P0743 Torque Converter Clutch Solenoid Circuit Electrical
Now i dont know a lot about automatics especially modern ones with all this fancy electronics thats used nowdays but i think its a fault with the temperature sensor for the gearbox.But where its located and what it looks like i have no idea it could even be mounted inside the gearbox .Sorry not a very good answer from a mechanic but?? very few of our europeon cars come with auto transmission .Evan when i do know whats wrong i cannot buy the parts for the gearbox as only re-con boxes supplied by the dealer so best advice is to try a specialist in auto box repairs only .PS some of my best students when i used to teach mechanics many moons ago were the girls so no excuses like iam only a girl please

Apr 22, 2013 | Cars & Trucks

1 Answer

Vehicle Speed Sensor


Cvt transmission is continuously variable transmission. VSS is vehicle speed sensor. A faulty sensor can make the transmission run erratic.

Jul 30, 2012 | 1997 Honda Odyssey

2 Answers

Po720 code and po733 code plus leaking oil


P0720-OUTPUT SPEED SENSOR ERROR

WHEN MONITORED
The transmission gear ratio is monitored continuously while the transmission is in gear.

SET CONDITION
If there is an excessive change in output RPM in any gear. This DTC can take up to five minutes of problem identification before illuminating the M.I.L.

POSSIBLE CAUSES[*]Output speed sensor signal circuit open[*]Speed sensor ground circuit open[*]Output speed sensor signal circuit short to ground[*]Speed sensor ground circuit short to ground[*]Output speed sensor signal circuit short to voltage[*]Speed sensor ground circuit short to voltage[*]Output speed sensor[*Powertrain Control Module (PCM)[*]Intermittent wiring and connectorsi cen get you a full flow chart on how to check it out if you wish

p0733 Gear 3 Incorrect ratio

Jan 03, 2011 | Chrysler Voyager Cars & Trucks

1 Answer

Where is the speed sensor on my 2004 Freestar?


Not sure what you are asking for but here is some info about the Speedometer and Speed Control.
Speedometer Gauge The instrument cluster receives the vehicle speed signal from the ABS module over the SCP communication network and commands the speedometer with an appropriate pointer placement based upon the data received.


The cruise control also gets the signal from the same source. The transaxle has an input speed sensor and an output speed sensor. They are primarily for transmission shifting. Hope this helps. Please don't leave me a bad thumbs up, I am trying to help with the info you have provided. ... Cobra.. :-)

Jun 15, 2010 | 2004 Ford Freestar

Not finding what you are looking for?
2007 Dodge Caliber SXT Sport Hatchback Logo

Related Topics:

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...