Question about Cars & Trucks

Open Question

How much is the upper and lower radiator hose of a crosswind isuzu

By pass hose break light switch and oil sending unit

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 95 rodeo coolant problems

hi
aj like
shum













Posted on Jun 19, 2008

Ad
  • 4 Answers

SOURCE: lower section of upper radiator hose seperated from filler cap ho

Dealer only place to get the whole 3 piece radiator hose assembly for problem you describe. Not bad price.I know this from my experience. Trust me I searched everywhere. T-stat located where diagram that was sent. $60.00 for part

Posted on May 22, 2009

ZJLimited
  • 17970 Answers

SOURCE: 1997 jeep cherokee sport 4x4,

I suggtes check in the Service Manual, in this link... Secc-7-Cooling-System

8042e4c.jpg

If the hoses are news, then its possible that your problem may be in the metallic coupling (lower radiator).

Tell us news.

Posted on Sep 14, 2010

shark2th667
  • 343 Answers

SOURCE: My 98' Isuzu rodeo Has just blown Head Gasket how

If you are not very mechanically inclined leave this to a shop, head gaskets can be very complicated for some. the block can be flushed once the head is removed or even before. the fan is actuated by a sensor (usually on the radiator). Replace it since the motor got that hot. Sorry to say you may have warped the head or even cracked it if the heat was that high. You need to invest in a mechanics manual for your vehicle and read all that pertains to cylinder head R & R before you attempt any of this yourself

Posted on Oct 02, 2010

  • 65 Answers

SOURCE: Ok, g35 coupe 06,52k miles Had

Heres a couple of things you can check. Start your car and remove the radiator cap,(before it gets hot mind you) when it reaches norm operating temp, look inside radiator to see if water is circulating. If its not moving, its a bad water pump. Also, youre hoses should never collapse, if they collapse when they get hot maybe you need new hoses? Finally, if those dont work, flush out your radiator. Open the bottom cockpit and use a garden hose and let it flush out the system while the car is running, about 10 mins should do the trick. If the radiator looks clean inside then it doesnt need flushed.

Posted on Jan 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the radiator on a 2003 Buick Lesabre


3.8L Engine

  1. Drain the engine coolant.
  2. Remove the upper radiator seal.
  3. Remove the upper tie bar.
  4. Disconnect the coolant overflow hose from the radiator.
  5. Plug the coolant overflow hose.
  6. Disconnect the upper and lower radiator hoses.
  7. Remove the transaxle oil cooler pipe bracket bolt from the lower tie bar.
  8. Remove the cooling fans.
  9. Slide the plastic cap off the transaxle oil cooler pipe quick connect fittings.
  10. Disconnect the upper and lower transaxle oil cooler pipes from the radiator.
  11. Remove the A/C condenser mounting bolts.
  12. Separate the condenser from the radiator.
  13. Lift the radiator up and out of the vehicle.
To install:
  1. Install the radiator to the vehicle. Place the bottom of the radiator in the lower pads.
  2. Install the condenser to the radiator.
  3. Install the A/C condenser mounting bolts and tighten to 115 inch lbs. (13 Nm).
  4. Push the upper and lower transaxle oil cooler pipes into the radiator quick connect fittings, until a "click" is heard.
  5. Tug gently on the cooler pipes to ensure proper retention.
  6. Slide the plastic caps (1) over the quick connect joints.
  7. Install the cooling fans.
  8. Install the transaxle oil cooler pipe bracket bolt to the lower tie bar and tighten to 89 inch lbs. (10 Nm).
  9. Install the upper and lower radiator hoses.
  10. Connect the coolant recovery hose to the radiator neck.
  11. Install the upper tie bar.
  12. Install the upper radiator seal.
  13. Fill the cooling system.
  14. Inspect the transmission oil level.

Nov 02, 2015 | Buick Cars & Trucks

2 Answers

How do you remove oil pan on 1993 Isuzu trooper 4x4


you have to make to unbolt the engine mountings,drain the radiator and remove the upper & lower radiator hoses and get the radiator out just to avoid any damage because you are going to lift the engine quite up so you could remove the engine oil pan over the front differential axle. Check whether is there any small pan cover where you can remove to have access into the oil pump and remove it.Would be much easier if you remove the oil pump.

Sep 03, 2012 | Isuzu Trooper Cars & Trucks

2 Answers

What is the normal oil pressure of an Isuzu crosswind gas engine


Not sure what a crosswind is, but normal oil pressure for most gasoline engines is 40 - 60psi depending on RPM and temp.

Jul 20, 2012 | 1999 Isuzu Trooper

1 Answer

How to remove radiator


  1. Drain the cooling system.
  2. Unfasten the upper fan shroud bolts and remove the upper fan shroud.
  3. If equipped, remove the upper panel fasteners and the panel.
  4. If equipped, remove the upper insulators and brackets.
  5. Disconnect the radiator upper and lower hoses and, if applicable, the transmission coolant lines.
  6. Remove the coolant recovery system line, if so equipped.
  7. Remove the oil coolant lines, if equipped.
  8. Remove the lower fan shroud bolts and the lower fan shroud.
  9. Remove radiator from the lower brackets and insulators.
  10. To install:

    1. Install the radiator on the lower brackets and insulators.
    2. Install the lower fan shroud and its retaining bolts. Tighten the shroud bolts to 71 inch lbs. (9 Nm).
    3. Attach and tighten the engine oil cooler pipe bolts to 18 ft. lbs. (24 Nm) and the transmission oil cooler bolts to 19 ft. lbs. (26 Nm).
    4. Attach the lower and upper radiator hoses..
    5. Install the upper insulators, the upper fan shroud and fan shroud bolts. Tighten the shroud bolts to 71 inch lbs. (9 Nm).
    6. Attach the coolant recovery system line, if so equipped.
    7. If equipped, install the upper panel fasteners.
    8. Refill the cooling system.

Jan 13, 2011 | 2001 Chevrolet Silverado 2500HD

1 Answer

Installing radiator


REMOVAL
1. DRAIN ENGINE COOLANT
2. w/ CRUISE CONTROL SYSTEM:
REMOVE CRUISE CONTROL ACTUATOR COVER
3. DISCONNECT ECT SWITCH CONNECTOR FROM FAN SHROUD
4. DISCONNECT ELECTRIC COOLING FAN CONNECTORS
5. REMOVE RADIATOR HOSES
(a) Disconnect the upper hose from the radiator side.
(b) Disconnect the lower hose from the water inlet pipe.
6. DISCONNECT RADIATOR RESERVOIR HOSE
7. A/T:
DISCONNECT OIL COOLER HOSES
8. REMOVE RADIATOR AND ELECTRIC COOLING FANS
(a) Remove the 2 bolts and 2 upper supports.
(b) Lift out the radiator.
(c) Remove the 2 lower radiator supports.
9. REMOVE RADIATOR LOWER HOSE
10. A/T:
REMOVE A/T OIL COOLER HOSES
11. REMOVE ECT SWITCH WIRE
12. REMOVE ELECTRIC COOLING FANS Assembly is reverse order.

Jan 01, 2011 | 1996 Toyota Camry

2 Answers

How to remove radiator from my 2000 chrysler 300


Radiator Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect negative cable.
  3. Drain cooling system.
  4. Remove or disconnect the following:
    • Radiator upper crossmember
    • Upper and lower coolant hoses from the radiator
    • Transmission hoses from cooler
    • Engine oil cooler lines (if equipped)
    • Radiator fan electrical connector and fan assembly
    • Condenser mounting screws located at the front of the radiator
    • Transmission cooler line bracket from left side of radiator
  5. Lift condenser upward enough to disengage upper mounting clips. Allow condenser to rest on lower radiator crossmember.
  6. Lifted radiator from engine compartment.
To Install:
  1. Seat the radiator assembly lower rubber isolators into the mounting holes in radiator lower support.
  2. Attach air conditioning condenser to radiator
    • Torque to 45 inch lbs. (5 Nm)
  3. Install or connect the following:
    • Radiator lower hose
    • Transmission cooler line bracket and transmission hoses
      1. Torque to 28 inch lbs. (3 Nm)
    • Radiator fan and electrical connector
    • Engine oil cooler lines (if equipped)
      1. Torque to 160 inch lbs. (18 Nm)
    • Radiator upper hose
    • Radiator upper support crossmember
    • Negative cable
  4. Fill cooling system with coolant.
prev.gif next.gif

Aug 03, 2010 | 1999 Chrysler 300M

1 Answer

How to remove and replace radiator on 1998 ford taurus


  1. Disconnect battery ground cable.
  2. Remove the battery.
  3. Remove clip retaining constant control relay module and position module aside.
  4. Remove battery tray.
  5. Remove radiator cap.
  6. Raise vehicle on hoist.
  7. Remove radiator splash shield.
  8. Drain engine cooling system.
  9. Remove radiator mounting bracket assembly.
  10. Remove lower radiator hose.
  11. Partially lower vehicle.
  12. Remove upper radiator hose.
  13. Remove radiator overflow hose.
  14. Remove upper A/C condenser core retaining bolts.
  15. Remove upper A/C transmission oil cooler tube clips.
  16. Remove upper transmission oil cooler tube (7C410) using 3-8 inch fuel line disconnect tool 310-041 (T90T-9550-C).
  17. Raise vehicle on hoist.
  18. Remove lower transmission oil cooler tube clips.
  19. Remove lower transmission oil cooler tube using 3/8 inch fuel line disconnect tool 310-041 (T90T-9550-C).
  20. Remove transmission oil cooler bracket and position transmission oil cooler aside.
  21. Remove lower A/C condenser core bolts and position A/C condenser core (19712) aside.
  22. Remove radiator support bracket.
  23. Remove radiator.

May 07, 2010 | 1998 Ford Taurus

2 Answers

How to remove a radiator from a ford taurus


Disconnect battery ground cable. Remove battery. Remove battery tray. Remove clip retaining contant control relay module and position module aside. Remove radiator cap. Raise vehicle front end as high as possible. Remove radiator splash shield. Drain radiator. Remove the radiator mounting bracket assembly. Remove lower radiator hose. Partially lower vehicle. Remove upper radiator hose. Remove radiator overflow hose. Remove upper A/C condenser core retaining bolts. Remove upper transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Raise vehicle. Remove lower transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Remove transmission oil cooler bracket and position transmission oil cooler aside. Remove lower A/C condenser core bolts and position A/C condenser core aside(be careful not to loosen the AC condenser lines. Remove radiator support bracket. Remove radiator out through the bottom of the vehicle.
Installation
Position radiator. Position radiator support bracket and tighten nuts. Position A/C condenser core and tighten lower A/C condenser core bolts. Position transmission oil cooler tube and install transmission oil cooler tube bracket. Install lower transmission oil cooler tube. Install lower transmission oil cooler tube clips. Install lower radiator hose. Install radiator mounting bracket assembly. Tighten bolts. Install radiator splash shield. Lower vehicle. Install upper tranmission oil cooler tube. Install upper transmission oil cooler tube clips. Install upper A/C condenser core retaining bolts. Tighten bolts. Install radiator overflow hose and tighten clamps securely. Install upper radiator hose. Position constant control relay module and clip securely. Install battery tray. Install battery. Connect battery ground cable. Fill and bleed cooling system. Start engine and inspect for leaks.

Nov 25, 2009 | 1998 Ford Taurus

1 Answer

RADIATOR REPLACEMENT


  • At the time of installation, please refer to the following items.
  • Start the engine, and check for coolant and A/T fluid leaks.
  • Check the A/T fluid level.
  1. Drain engine coolant.
  2. Canada: Disconnect relay block (for daytime running light system) from battery hold-down clamp.
  3. Disconnect upper radiator hose from radiator.
  4. Disconnect lower radiator hose from water inlet pipe.
  5. Disconnect A/T oil cooler hoses from oil cooler pipes.
  6. Disconnect No.1 and No.2 cooling fan connectors.
  7. Disconnect No.1 Engine Coolant Temperature (ECT) switch wire connector.

  8. Remove radiator and cooling fans assembly.
    1. Remove the 2 bolts and 2 upper supports. Torque: 12.8 Nm (9 ft. lbs.)
    2. Lift out the radiator, and remove the radiator and cooling fans assembly.
    3. Remove the 2 lower supports.
  1. Remove A/T Oil cooler hoses from radiator.
  2. Remove lower radiator hose from radiator.
  3. Remove No.1 ECT switch.

  4. Remove No.1 cooling fan from radiator. Remove the 2 bolts and cooling fan. Torque: 5.0 Nm (44 inch lbs.)
  5. Remove No.2 cooling fan from radiator. Remove the 3 bolts and cooling fan. Torque: 5.0 Nm (44 inch lbs.)
INSTALLATION
Installation is in the reverse order of removal.

Nov 06, 2008 | 1992 Lexus Es 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...