Question about 2008 Pontiac Torrent

1 Answer

No power i am getting no power in the vehicle at all and the key is stuck in the ignition. i had it hook up to a half ton chevy for about 30 minutes and didnt have any progress. i checked all the fuses and they wee all good minus the auxiliary power (20a) fuse which i replaced. i disconnected the battery and hooked it back up and still had nothing.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 44 Answers

Check relays

Posted on Jan 03, 2014

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 19 Answers

SOURCE: Car won't start

Check the lever for putting the car in park/drive.
If the switch/sensor that detects where it is at (i.e. P, R, N, D, 2, 1) is broken or loose, it may think the car is not in Park and cars with automatic transmissions will not start unless they are in Park.
It might also be the starter is bad.

Ken P.

Posted on May 16, 2008

motorhead427
  • 24 Answers

SOURCE: Aztek won't start,key locked in ignition, service engine light on

It is the security chips in the keys. Has this car been wrecked? Was this car made in Mexico? GM had the bright Idea of creating a security system that would do exactly this, I know on cars made in Mexico (like the HHR) You can reset the power and get the key back out, but vehicle will have to be reprogrammed with the master key. This involves turning the key from off to run position without ever going past run (i.e. start position) leave key in this position for 30 minutes. Turn key back to off for 30 seconds then back to run for 30 minutes. repeat this step three times. the last time, after 3rd 30 minute period, turn key off for 30 seconds and then try to crank. Please note this only works if the original master key is being used. You can then reprogram the second key following a similar sequence, only master key that is working has to be inserted to let alarm system know that vehicle is not being stolen only that you are trying to reprogram a key. If original master key is not being used then vehicle has to be taken to the GM dealership to program keys and possible key module replacement.

Posted on May 30, 2009

emissionwiz
  • 76691 Answers

SOURCE: fuel pump fuse blowing

replace the fuel pump, it is drawing to much current, this is common when the pump bearings get worn out, also make sure you replace the fuel pump connector at the fuel tank connection, it will be burnt..

Posted on Jul 02, 2009

judd0081
  • 334 Answers

SOURCE: I have a 95 firebird.

It's when the security light starts flashing that the infamous "chip" in the key becomes a nightmare to many. Gradually the car begins not cranking anymore or if it cranks it would start and die in a second. Randomly it will do this more and more often until it won't start anymore. VATS, PASSkey and Passlock immobilizer systems are killing cars all over North America, they have a short lifespan and are certainly more effective against owners than thieves. Here is how you save your car
1st trick, Try a spare key that is newer or used less. The pins wear down and so do the keys causing security fail. 2nd trick, (if not starting) turn the key forward 2 clicks till right before it would normally start, leave like that for 10 minutes. ( no less ) After 10 minutes, turn key back then forward and your car might start. I did this in my regal for more than a year. If its shutting down while running, im sorry i have no quick fix... If anything on this page helps you, please remember to comment or give me a thumbs up on the myfixya sight so i can have a better rating to help more people on this. Thanks

Cheap fix: Bypass the chip in your key. Temporary, but effective. Until the TDM (theft deterrent module) in the dash poops out, then you're kinda screwed. I was told that these types of key security systems have a 7-10 year life span. Sucks for us. This link explains the "Key Issue" pretty well.
----- http://vats.likeabigdog.com/


Never worry again fix: Bypass the whole VATS/Passlock/passkey I or passkey II system entirely. Literally take it out, and throw it away. I just did this in my Regal. Took about an hour. Took longer to find the thing than it did to fix the problem. They sell a unit for 200 bucks to totally bypass this system FOREVER. life time-money back and all that. Finally did this in my car. Well worth the 200 if you've looked into getting this replaced... Anywhere from 600-1000 bucks. If you do buy this, please purchase it thru this link. The cost is the same, but i get credit for the sale and im trying to earn my money back, as you will be able to do if you buy fron NewRockies and join the free affiliate program. Thanks
----- http://newrockies.ca?ap_id=judd0081 ----- With this fix, you can take that whole Vats, passlock, passkey system out of your car all together. Good info on both sites.

It works for:
Any GM or Isuzu Vehicle with VATS or PASSKey or PASSLock security systems.
If your car has the chip in the key or in the lock cylinder, then you can save it with this Full Bypass.
Trucks
.
GMC/Chevy
1998-2006 S10/T10/Sonoma
/Blazer/Jimmy
1998-2007 Suburban/Avalanche
/Tahoe/Yukon
1998-2006 Sierra/Silverado
2002-2008 Trailblazer
2003-2006 SSR
1998-2006 C1500/C2500/C3500
1998-2006 K1500/K2500/K3500
2003-2007 Hummer H2
.
Isuzu
1998-2000 Hombre
2005-2006 I280/I350
2007-2008 I290/I370
.
Cars/Vans
.
Isuzu
2003-2007 Ascender
.
Pontiac
1994-2003 Grand Prix
1998-1999 Montana
2006 Torrent
1996-2005 Grand AM
1994-1998 Trans Sports
1988-1999 Bonneville
1988-2002 Firebird
1995-2005 Sunfire
1996-2002 Trans Am
.
Buick
2004-2007 Rainier
1994-2005 Century
1993-2004 Regal
1982-1999 LeSabre
1991-1996 Park Avenue / Ultra
1994-1996 Roadmaster
1991-1996 Roadmaster Estate Wagon
1982-1999 Riviera
1988-1991 Reatta
1996-1998 Skylark
1982-1990 Electra (all models)
.
Oldsmobile
1996-1998 Achieva
1999-2004 Alero
1994-2004 Aurora
1998-2004 Bravada
1991-1993 Delta 88
1994-1999 Eighty-Eight
1991-1996 Nighty-Eight
1998-2002 Intrigue
1990-1992 Toronado
1994-1997 Cutlass Supreme
1997-1999 Cutlass
1997-1999 LSS/Regency
1997-1999 Silhouette
1991-1996 Custom Cruiser
.
Chevrolet/GMC
1998-2005 Astro/Safari
1998-2008 Envoy
2005-2006 Equinox
1998-2007 Savana/Express
1995-2005 Monte Carlo
1997-1999 Venture
1995-2001 Lumina
1988-2002 Camaro
1995-2005 Cavalier
1982-2004 Corvette
1994-1996 Caprice/Caprice Wagon
1995-1996 Impala SS
2000-2005 Impala
1997-2005 Malibu Classic
1997-2003 Malibu
.
Cadillac
1986-1993 Allante
1982-1996 Fleetwood
1985-1996 Fleetwood Brougham
1992-2004 Seville
1992-2004 SLS/STS
1985-1999 Deville
1994-1999 Deville Concours
1997-1999 Deville D'Elegance
1988-2002 ElDorado
1994-2002 ElDorado Touring
1999-2007 Escalade
.
Saturn
2000 LS/LS1/LS2/LW1/LW2
2001-2002 L100/LW100
2001-2003 L200/LW200
2001-2005 L300/LW300
2004-2005 L-Series
2002-2008 VUE
1996-2002 SL/SL1/SL2
1996-2002 SC1/SC2
1996-2002 SW1/SW2

Posted on Feb 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2003 chevy tahoe with key stuck in ignition. vehicle previously broken into and stolen with scewdriver to ignition. ignition replaced. key now stuck and cannot turn vehcile off. can shift to driver,...


I have towed several of these with same problem. Sounds like to me it needs to go back in for the ignition switch again. Unless it's not going into park. If it's not going into park it would be a shift linkage issue and needs to be adjusted. Chris J.C. Towing & Recovery

Apr 09, 2010 | 2002 Chevrolet Tahoe

1 Answer

Pass lock problems


Your Passlock may need to relearn the ignition keys, if the ignition lock has gone bad like my in-laws Grand Am Gt, here is what i did so they will not get stranded any more. Buy a Passlock by pass module for around $70.00. You can order one from GMPASSLOCK.COM in the mean time try resetting the Passlock. Good luck

Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure
1.) Turn ON the ignition, with the engine OFF.
2.) Attempt to start the engine, then release the key to ON; the vehicle will not start.
3.) Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF.
4.) Turn OFF the ignition switch, and wait 5 seconds.
5.) Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes.
The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
6.) Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
7.) With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles.

Without a scan tool you may have momentary starter interruptions while history clears itself.



Jan 18, 2010 | 2000 Chevrolet Impala

1 Answer

Have 2003 chevy tahoe the security light flahs wont start


Your Passlock may need to relearn the ignition keys, if the ignition lock has gone bad like my in-laws Grand Am Gt, here is what i did so they will not get stranded any more. Buy a Passlock by pass module for around $70.00. You can orderone from GMPASSLOCK.COM in the mean time try resetting the Passlock. Good luck

Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself.

Dec 18, 2009 | 2003 Chevrolet Tahoe

1 Answer

Just replaced steering coluim in a 2002 chevy cavalier and the car won't start how do i get the theftlock code


Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself.

Nov 22, 2009 | 2002 Chevrolet Cavalier Coupe

1 Answer

Aztek won't start,key locked in ignition, service engine light on


It is the security chips in the keys. Has this car been wrecked? Was this car made in Mexico? GM had the bright Idea of creating a security system that would do exactly this, I know on cars made in Mexico (like the HHR) You can reset the power and get the key back out, but vehicle will have to be reprogrammed with the master key. This involves turning the key from off to run position without ever going past run (i.e. start position) leave key in this position for 30 minutes. Turn key back to off for 30 seconds then back to run for 30 minutes. repeat this step three times. the last time, after 3rd 30 minute period, turn key off for 30 seconds and then try to crank. Please note this only works if the original master key is being used. You can then reprogram the second key following a similar sequence, only master key that is working has to be inserted to let alarm system know that vehicle is not being stolen only that you are trying to reprogram a key. If original master key is not being used then vehicle has to be taken to the GM dealership to program keys and possible key module replacement.

May 30, 2009 | 2001 Pontiac Aztek

1 Answer

Need the procedure to program my new remote...THANKS!!!


1. Close all vehicle doors.

2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).

6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.

May 20, 2009 | 2005 Chevrolet Silverado

1 Answer

2002 chevy trailblazer


i have the same problem i think its a saftey hazzard when i went to start my car it was dead and the key would not come out and i couldnt shift it in (N) to move it even the button that u push to shift out of park didnt work

Jul 27, 2008 | 2001 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...