Question about 2006 Chevrolet Silverado

1 Answer

Need to remove left rear door panel

How to remove left rear door panel on a 2006 silverado

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,984 Answers

  1. If equipped, remove the window crank handle by using a retaining clip removal tool.
  2. Remove the door handle bezel by inserting a flat trim removal tool between the door panel and handle bezel to release the locking tabs.
  3. Remove all door panel electrical connectors .
  4. Remove the door panel push pins and trim screws. Lift the door panel up and out to release the door panel locking tabs.

Posted on May 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Tahoe. Where is the auxiliary blower motor located?


It is located behind the right rear quarter panel , In the back right of the interior !
Remove the right rear quarter trim panel. Refer to Rear Quarter Trim Panel Replacement - Right Side in Interior Trim.
Removal Procedure
  1. Remove the rear seat. Refer to Rear Number 2 Seat Replacement or Rear Number 2 50-50 Seat Replacement in Seats.
  2. Remove the Third Pillar trim panel. Refer to Third Pillar Trim Replacement .
  3. Remove the garnish molding. Refer to Body Rear Corner Garnish Molding Replacement .
  4. Remove the door sill plate. Refer to Liftgate Door Sill Plate Replacement .
  5. Remove the quarter panel trim screws.
A lot involved in this but not to difficult !
  1. Remove the rear door sill trim plate. Refer to Front Side Door Sill Plate Replacement or to Rear Side Door Sill Plate Replacement .
  2. Remove the lower rear seat belt cover and bolt.
  3. Remove the trim panel from the vehicle.
Remove the sill plate. Firmly pull the sill plate up and out from the retainers.
Remove the sill plate from the vehicle. Start from the front of the door sill. Use a flat-bladed tool in order to pry the door sill plate.
Rear Side Door Sill Trim Plate Replacement
Use a flat-bladed tool in order to pry the door sill plate. Remove the sill plate from the vehicle.
Body Rear Corner Garnish Molding Replacement
Remove the rear upper garnish molding. Refer to Rear Upper Garnish Molding Replacement .
Pull down on the upper corners of the garnish molding in order to disengage the retaining clips. Pull in order to disengage the remaining retaining clips. Remove the rear corner garnish molding from the vehicle. Inspect the rear corner garnish molding for broken or missing retaining clips. Replace the retaining clips as needed.
Good Luck ! Fun job !!!!!

Jun 07, 2015 | 2006 Chevrolet Tahoe

1 Answer

Remove rear door panel 2006 toyota sequoia


here is a video,hope it helps

https://www.youtube.com/watch?v=ht2GD4GvJ_c

Mar 04, 2015 | 2006 Toyota Sequoia

1 Answer

Door panel removal


there should be screws near the inner handle and check around the perimeter of the plastic panel

May 02, 2014 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

The driver side electric door panel doesn't work on my '06 Chevy.


Gonna need to remove the panels and see where you left some wiring disconnected or pinched.

Oct 30, 2012 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

I need help pulling the door panel off of my 2006 audi a4


Normally there are four screws to remove. Top left and right of the panel and under the door pull. Remove screws and lift the panel straight up. There is a shield under the door pull . Remove screw and pop out shield. Door panel screws should be visible.

Dec 21, 2010 | 2006 Audi A4

1 Answer

I need to replace the rear inside door handle on my Licoln Zephyr (2006). Do I need to take off the door panel?


Typical on most GM cars, the door panel will need to come off in order to replace the door handle. Sometimes you can simply remove the panel around the door knob to replace. However as stated above, on most GM models, you'll usually have to remove the whole panel to get at it.

You'll usually need a torq screwdriver, and a straight blade screwdriver, hammer (to reinstall the door panel) and in some cases a Phillips. Remove the door panel with care, because of the many wires and electrical connections inside, and to avoid breaking the plastic pivots that hold the panel snug against the door .

May 25, 2010 | 2006 Lincoln Zephyr

1 Answer

I need to changeout a broken left rear door window, What do i need to do to get the old glass out


remove the panel screws and the handle screws and clips usually behind window handle, if electric ok.
remove panel lift bottom out and panel up after clearing door base, be careful not to pull wires or break plastic. lower window so bolts of lower/mid
trac is visible. loosen but have someone hold the window from falling inside, it will break easily so don't torque or drop it inside. once trac is loose remove
through top but turning if necessary to clear the top of the door. not too easy

Feb 10, 2010 | 2006 Ford Five Hundred

1 Answer

2006 Tahoe Z71 Rear door will not unlock


The rear door lock/actuator assembly has failed and will need to be replaced. I had one in the shop recently and my tech had to remove the inside trim panel and manually open the rear hatch before it could be repaired.

2b4e2f1.gif

Sep 07, 2009 | 2006 Chevrolet Tahoe

1 Answer

Power door locks on rear doors do not open


The rear doors have a separate relay for the lock and unlock function. There's a good chance the unlock relay is bad. The relays in question are located in the left instrument panel fuse block. Hope this helps

Oct 10, 2008 | 2003 Chevrolet Silverado 2500HD

Not finding what you are looking for?
2006 Chevrolet Silverado Logo

1,049 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...