Question about 2003 Hyundai Tiburon

1 Answer

Positive battery terminal connection remove

I have a 2003 Hyundai Tiburon and the positive clamp is not coming off. Its seems as if it's super glued to the battery. However, there was corrosion on the conductors and it is 2 degrees outside. Help!

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 338 Answers

If it\'s the dome type clamp, take the screw out, and pour a drop of brake fluid in the screw hole, other types of clamps. Slacken as much as you can, use brake fluid! cover the terminal and clamp and let it soak in. You can try and start the vehicle, if its a bad connection it may heat up a little which will help. DONT TRY AND HEAT IT UP WITH A NAKED LIGHT, a battery gives of hydrogen and a naked light might cause an explosion

Posted on Jan 03, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 74 Answers

SOURCE: 2003 tiburon transmission

if you have a 4 cylinder you wiggle the clutch shaft up and down remove the lever and this will get the fingers off the releasbearing / 2 starter bolts 2 large bolts up top 3 under exhaust and 4 0n the other side lower one is above right inner cv axle, remove left axle from car right axle can moved over un do ball joint 3 mounts remover upper side and reaar , strap engine to a cradle or 4,4 post chained to support engine you can slide tranmission over14 inches with room to stick your hands in and remove pressure plate ,fly wheel can be removed but takes good hands tricky,now thats a hyundai flat rate tech procedure for 4 cyl, IF YOUR NOT SURE ABOUT or if the engine is V6 cylinder THE SUB FRAME COMES OUT you can remove rack hose on sub frame and 4 bolts and wire or strap the steering rack to body at that can stay in car or you will have to take rack out with sub frame

Posted on Sep 25, 2008

alicantecoli
  • 22219 Answers

SOURCE: 2003 hyundai tiburon alarm system

factory fitted alarm?? no way its done through the ECU and shuts down the spark via the processor and try finding a wiring diagram??

Posted on Feb 09, 2009

ghost4548
  • 776 Answers

SOURCE: Location of the Purge Control Valve for 2003 Hyundai Tiburon

There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
22c99c7.jpg

And the 2.7 Liter V6:
cb31feb.jpg

Posted on Jun 06, 2009

ghost4548
  • 776 Answers

SOURCE: Need Instructions on 2003 Hyundai Tiburon Clutch Replacement

Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Posted on Jun 14, 2009

  • 1 Answer

SOURCE: 2003 Hyundia Tiburon BCM

http://www.newtiburon.com/forums/showthread.php?t=102241&highlight=bcm

Posted on Jun 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace ignition switch on a hyundai tiburon


Removal & Installation

Specific to:
Hyundai Entourage 2007-2008
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative (-) battery terminal.
  3. Remove the crash pad lower panel (A).

    0996b43f80e41e86.jpg
    enlarge_icon.gifenlarge_tooltip.gif
    Fig. Remove the crash pad lower panel (A)
  4. Remove the 2 screws (A) and the trip switch connector.
  5. Remove the crash fascia panel (B).

    0996b43f80e41e87.jpg
    enlarge_icon.gifenlarge_tooltip.gif
    Fig. Remove the crash fascia panel (B)
  6. Remove the screw with the ignition in the ON position (IG ON) and disconnect the 6P connector.
  7. Remove the ignition switch (A).
  8. Installation is the reverse of removal procedure.

    0996b43f80e41e88.jpg
    enlarge_icon.gifenlarge_tooltip.gif
    Fig. Remove the ignition switch (A)
Specific to:
Hyundai Accent 2006-2008
Hyundai Azera 2006-2008
Hyundai Elantra 2006-2008
Hyundai Sonata 2006-2008
Hyundai Tiburon 2006-2008
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    The negative battery terminalThe crash pad lower panelThe ignition switch after loosening the screw with IG ON and disconnecting the 6P connector
  3. Installation is the reverse of the removal procedure.hope this helps it is off autozone website

Aug 02, 2014 | 2006 Hyundai Tiburon

2 Answers

I'm trying to change the battery on my 2006 Tiburon. How do I get a tight connection on the positive post with just a screw going down into the top? It's not holding the cover to anything at all.


I would go to an Auto supply store and look for a replacement batt terminal. a clamp type might be best. You would have to cut off the existing one and install the new one. Person in store might help with suggestions.

Aug 18, 2011 | 2006 Hyundai Tiburon

1 Answer

I have a 2003 Hyundai tiburon. I need to replace the battery. I disconnected both the positive and negative cables. I cannot remove the battery no matter how hard I try. Is the battery bolted down? The...


YES.. the battery is bolted down w/a 12mm bolt. You need to look harder. Toward the front of the battery. You will find a battery lock-down plate and its 12mm bolt.

Jun 29, 2011 | 2005 Hyundai Tiburon

1 Answer

How to change a battery for 2006 Hyundai Tiburon GT? Theres a nut with a washer that is screwed down on the battery terminal


Just remove the nut and washer on both post. If you have a rod that locks the battery down, loosen it up so you can remove the clamp that holds the battery down.
Remove negative battery cable first, then positive cable.
When putting the cables back on, positive gets put on first, then negative.

Sep 29, 2010 | 2006 Hyundai Tiburon

1 Answer

There is a wierd metal housing on the positive battery post. i need to replace the battery but don't want to damage this when taking off. HEEEELP!


that wierd metal housing is the pos. terminal and they ****, remove the 10mm nut on top, use a good pair of pliers or vicegrips and grasp it firmly and lovingly rock it from side to side while aplying upward presure, a new one can be obtained at your local hyundai dealer there pretty cheap.

Oct 11, 2009 | 2003 Hyundai Tiburon

1 Answer

Cant get positive terminal off its post


Buy a battery cable remover. It lookc like a clamp. The hooks go under the cable end and the post goes to the center of the terminal. When you turn it, the terminal will pop right off. About $5.

Mar 21, 2009 | 2003 Hyundai Tiburon

1 Answer

Fuel Filter


FUEL FILTER REPLACEMENT
1. Reduce the internal pressure of the fuel pipes and hoses by completing the following operations. (1)
Disconnect the fuel pump harness after removing the rear seat cushion. (2)
Start the engine and after it stalls, turn the ignition switch OFF. (3)
Disconnect the battery negative (-) terminal.
bf8695b.gif (4)
Connect the fuel pump harness connector

2. Remove the bolt connecting the fuel line with the fuel filter. Cover with a shop towel to avoid gasoline from splashing. 3. Remove the fuel filter mounting bolt, then remove the fuel filter from the fuel filter clamp. 4. After replacing the fuel filter, check for fuel leaks.
1ff5185.gif

Jun 09, 2008 | 2001 Hyundai Tiburon

1 Answer

4 cylinder motor


http://www.analogstereo.com/pdf/om/hyundai_tiburon_owners_manual_2003.pdf
note_icon.gif Mark all wiring and hoses to avoid misconnection. Inspection the timing belt before removing the cylinder head. Turn the crankshaft pulley so that the No. 1 piston is at top dead center
1. Disconnect the neagative terminal from the battery 2. Remove the engine cover. . Drain the engine coolant. Remove the radiator cap to speed draining. 4. Remove the intake air hose and air cleaner assembly. (1) Disconnect the AFS connector. (2) Disconnect the breather hose from air cleaner hose. (3) Remove the intake air hose and air cleaner. 5. Remove the upper radiator hose (A) and lower radiator hose (B). 6. Remove the heater hoses 7. Remove the engine wire harness connectors and wire harness clamps from the cylinder head and the intake manifold. (1) OCV(Oil Control Valve) connector (A). (2) Oil temperature sensor connector (B). (3) ECT (Engine Coolant Temperature) sensor (C) connector. (4) Ignition coil connector (D). (5) TPS (Throttle Position Sensor) connector (A). (6) ISA (Idle Speed Actuator) connector (B). (7) CMP (Camshaft Position Sensor) connector (A). (8) Four fuel injector connectors (B). (9) Knock sensor connector (C).

May 27, 2008 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...