Question about 2009 Saturn Aura XR

Open Question

How to sequence brake bleeding on a saturn aura

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
redlinetech0
  • 33 Answers

SOURCE: How to replace brakes on a 2007 saturn aura

you will need a 19mm socket to get the wheels off, a 13mm to get the caliper off, and a 15mm to get the caliper bracket off and rotor loose.

Posted on May 18, 2009

Ad
bdubsee
  • 75 Answers

SOURCE: Saturn Aura 2007 Rear Brakes

The trick is to remove the cap on the brake fluid reservoir on the firewall under the hood before squeezing the caliper. Be sure to replace the cap before attempting to press the brake pedal.

Posted on Jan 25, 2010

  • 1 Answer

SOURCE: do i use a c-clamp to get the piston back in place

piston will not go back in with a C clamp. They make a reset tool but a pair of pliers will work just fine. Place the pliers in the two v shaped slots and turn clockwise. This will turn the piston back in.

Posted on Mar 27, 2010

  • 172 Answers

SOURCE: 2007 Saturn aura humming noise once you rech about

go little faster- move steering a little to left and then to the right,
what side is louder,
sounds as if you have a hub going bad

Posted on Apr 16, 2010

bdubsee
  • 75 Answers

SOURCE: how to change a headlight bulb in a saturn aura?

Access to change the headlamp bulbs is through the wheel well. The recommended method is to remove the front tire and then the plastic inner fender liner. Once removed, you'll have easy (more or less) access to the rear of the headlamp housing.

Posted on Oct 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 Saturn, Aura. Heater does not blow hot, slow coolant leak, & it also over heats. Please help! I'm freezing when I'm in my car!!!


You need to fix the coolant leak, then refill and bleed cooling system, then you will get heat and cure overheating problem too

Dec 16, 2015 | Cars & Trucks

1 Answer

Bleed brakes and will not hold aftet bleeding


You have to bleed the whole system in sequence. It is a two man job. you have air in the system. You must bleed each wheel starting with the wheel farthest from the master cylinder. then the next wheel that shares the same circuit then the next and the next. Each car has its own sequence to follow. front wheel drive cars bleed differently than rear wheel cars . You must keep the master cylinder full as you do this, as to not allow any more air to enter the system. If air has entered the ABS system it will have to be bleed as well .. You have to refer to a manual for your car.

Mar 11, 2015 | 2004 Saturn VUE

1 Answer

Aura speedometer light goes out


PDF]2007 Saturn AURA Owner Manual

www.saturn.com/.../saturn/.../2007/aura/2007-saturn-aur... Saturn Corporation2007 Saturn AURA Owner Manual M. 1 ... trademarks, and the name AURA is a trademark ... Warning Lights, Gages, and Indicators in ..... Get it up to speed.

Apr 14, 2013 | 2007 Saturn Aura XR Sedan

2 Answers

I have a 2008 saturn aura the brake lights come on by themselves, when you apply the brakes the lights go out. And the cruise will not work at the same time. The problem is very random.


Hello: Possible intermittent brake light switch, it could be loose or misadjusted. You may have to replace it. It is mounted on the brake pedal assembly.

Aug 05, 2011 | 2008 Saturn Aura

1 Answer

2007 saturn aura- when i press down on parking brake pedal, it easily goes to the floor. i looked under there and the cable doesnt move. how do i tighten this up, or did the cable come out of some sort of...


The parking brake cable has probably snapped. Look under the vehicle and see if the cables are loose, at the calipers. If so, you will need a new brake cable. Hope this helps...

Mar 05, 2011 | 2007 Saturn Aura XR Sedan

1 Answer

How to bleed brakes on 1997 Saturn


The brake system bleeding procedure differs for ABS and non-ABS vehicles. The following procedure pertains only to non-ABS vehicles. For details on bleeding ABS equipped vehicles, refer to the ABS procedures later in this section.

WARNING Make sure the master cylinder contains clean DOT 3 brake fluid at all times during the procedure.
  1. The master cylinder must be bled first if it is suspected of containing air. Bleed the master cylinder as follows:
    1. Position a container under the master cylinder to catch the brake fluid.
    2. Loosen the left front brake line (front upper port) at the master cylinder and allow the fluid to flow from the front port.
    3. Connect the line and tighten to 24 ft. lbs. (32 Nm).
    4. Have an assistant depress the brake pedal slowly one time and hold it down, while you loosen the front line to expel air from the master cylinder. Tighten the line, then release the brake pedal. Repeat until all air is removed from the master cylinder.
    5. Tighten the brake line to 24 ft. lbs. (32 Nm) when finished.
    6. Repeat these steps for the right front brake line (rear upper port) at the master cylinder.
WARNING Do not allow brake fluid to spill on or come in contact with the vehicle' finish, as it will remove the paint. In case of a spill, immediately flush the area with water.
  1. If a single line or fitting was the only hydraulic line disconnected, then only the caliper(s) or wheel cylinder(s) affected by that line must be bled. If the master cylinder required bleeding, then all calipers and wheel cylinders must be bled in the proper sequence:
    1. Right rear
    2. Left front
    3. Left rear
    4. Right front
  2. Bleed the individual calipers or wheel cylinders as follows:
    1. Place a suitable wrench over the bleeder screw and attach a clear plastic hose over the screw end.
    2. Submerge the other end in a transparent container of brake fluid.
    3. Loosen the bleed screw, then have an assistant apply the brake pedal slowly and hold it down. Close the bleed screw, then release the brake pedal. Repeat the sequence until all air is expelled from the caliper or cylinder.
    4. When finished, tighten the bleed screw to 97 inch lbs. (11 Nm) for the front, or 66 inch lbs. (7.5 Nm) for the rear.
  3. Check the pedal for a hard feeling with the engine not running. If the pedal is soft, repeat the bleeding procedure until a firm pedal is obtained.
zjlimited_349.jpg

Fig. 1: Loosen the front brake line in order to bleed the master cylinder

zjlimited_350.jpg

Fig. 2: Connect a bleed hose from the bleed valve on the front caliper to a jar of brake fluid

zjlimited_351.jpg

Fig. 3: Always follow the lettered sequence when bleeding the hydraulic brake system





Hope this helps to solve it; remember to rate this answer.

Dec 29, 2010 | 1997 Saturn SL

1 Answer

Bleeding the brakes on a 2005 saturn vue


I would start by removing the wheels and finding the bleed screw or bolt.
Pour a little brake fluid on the bolt to free up the rust that will form over time.
Then use a box end wrench to open the bleeder.

Fill the master cylinder with brake fluid and have some ready to add as you bleed the brakes.

Have an assistant push down on the brake pedal until it bottoms out and fluid squirts out of the bleeder screw area.

Watch your eyes.

Then tighten the bleeder screw.

Have them pump up the brakes again.

Do this in sequence from the furthest wheel from the master cylinder to the closest, and you'll be done.

Oct 09, 2010 | 2006 Saturn Vue

1 Answer

Proper brake pad replacement procedure for 2007 saturn aura


The proper replacment proceedures for saturn aura brake pads front is to take off your wheels, unbolt the caliper housing on it. You should also replace the shims when you replace the brake pads, it's the metal brackets around the pads. The new brake pads slide into place. If i was you I would also replace the caliper pin boots with new ones aftermarket. My car had a warping issue and a uneven brake pad wear and this fixed both problems. Need anything else ask, the tire should be retorqued to 100ft/lbs when you reassemble everything.

Sep 02, 2010 | 2007 Saturn Aura XR Sedan

1 Answer

Saturn Aura 2007 Rear Brakes


The trick is to remove the cap on the brake fluid reservoir on the firewall under the hood before squeezing the caliper. Be sure to replace the cap before attempting to press the brake pedal.

Jan 17, 2010 | 2007 Saturn Aura XR Sedan

1 Answer

Brake lights stopped working 2009 saturn aura


take back 2 the dealer its under its under warienty

Feb 11, 2009 | 2009 Saturn Aura

Not finding what you are looking for?
2009 Saturn Aura XR Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...