Question about Toyota HiAce

1 Answer

Engine codes p0108 ford


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Toyota Master
  • 20,706 Answers

Post a full question , ????????????????
weak engine power, and P0108
on a Ford Toyota HiAce, is this and engine swap?

Posted on Jan 03, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 2005 300 has code p0108

Check out this website:
'P0108 - Manifold Absolute Pressure/Barometric Pressure Circuit High Input (possible Map Sensor)
Possible Causes:
Faulty Manifold Absolute Pressure sensor
- Manifold Absolute Pressure harness is open or shorted
- Manifold Absolute Pressure sensor circuit poor electrical connection
- Faulty Engine Control Module (ECM)
Possible Symptoms:
Engine Light ON (or Service Engine Soon Warning Light)
- Engine rough idle
- Engine hesitation"

Apr 17, 2015 | Cars & Trucks

1 Answer


Code 108 is for a problem with the map sensor that measures engine vac.
The sensor would need to be tested.

Feb 10, 2013 | 2005 Mitsubishi Endeavor

1 Answer

Have a 108 code show up on a 1999 sunfire what might the problem be

Potential causes of a P0108 code:

  • Bad MAP sensor
  • Leak in vacuum supply line to MAP sensor
  • Engine vacuum leak
  • Short on signal wire to PCM
  • Short on reference voltage wire from PCM
  • Open in ground circuit to MAP
  • Worn engine causing low vacuum

got from here

Dec 08, 2012 | Pontiac Cars & Trucks

1 Answer

D0108 fault code

I will assume this is a "P" code.

P0108 FORD - Manifold Absolute Pressure/Barometric Pressure Sensor High Inputxicon.jpg CodePossible causes- Manifold Absolute Pressure harness is open or shorted
- Manifold Absolute Pressure sensor poor electrical circuit connector
- Faulty Manifold Absolute Pressure sensor
- Faulty Engine Control Module (ECM) When is the code detected?The Engine Control Module (ECM) has detected a performance fault with the anifold Absolute Pressure (MAP) sensorSymptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Engine rough idle
- Engine hesitation

Read more:

Jul 26, 2012 | 2003 Lincoln Aviator

2 Answers

My 2005 mustang has it's engine light on. the code was p0108. i replaced the map air flow sensor and re set the battery and the engine light went off for a minute. i drove my car about a mile and the...

You now know that the MAP sensor was only being effected and was not the problem. Here are a few possible causes for the high signal transfer of the circuit:

  • Leaking EGR valve
  • Vacuum leaks
  • Dirty fuel injectors
  • Wrong fuel pressure
  • Low engine compression
  • Ignition miss
  • Carbon deposits on the intake valves
  • Valve problems

Sep 13, 2011 | 2005 Ford Mustang

2 Answers

I have a 2000 Dodge Durango with 128,000 miles. The check engine light has been on and off the past few days. The OBD II code is P0108. What does this mean?

P0108 - MAP (Manifold Absolute Pressure/Barometric Pressure) Circuit High Input
The MAP (Manifold Absolute Pressure) sensor measures engine manifold negative air pressure. It's usually a three wire sensor: a ground wire, a 5 volt reference wire from the PCM (Powertrain Control Module) to the MAP sensor, and a signal wire that informs the PCM of the MAP sensor voltage reading as it changes. The higher the engine vacuum, the lower the voltage reading. The voltage should range between about 1 volt (at idle) to about 5 volts (WOT wide open throttle).

If the PCM sees the voltage reading from the MAP sensor is greater than 5 Volts, or if the voltage reading is higher than what the PCM considers normal under certain circumstances, a P0108 DTC will set.

Contact us if need additional details; good luck.

Sep 04, 2011 | 2000 Dodge Durango

1 Answer

What are these codes that appears on my engine check machines? p1391,p1297,p0108,p1492

P1391 Intermitant loss of cam or crank; P1297 No change in map from start to run; P0108 Map sensor voltage too high; p1492 Battery temp sensor too high.

Apr 16, 2011 | 2002 Chrysler Sebring

1 Answer

P0108 do i need to change my intake gasket? starts and idles poor and sometimes dies in morning may not do it for days, once it warms up it runs great!

It's entirely possible the intake manifold gasket has failed. An engine vacuum leak is a potential cause of the P0108 code.

For full details, see

Sep 23, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer


Definition of check engine code P0108:
Generic (Common for all car manufacturers):
Manifold Absolute Pressure/Barometric Pressure Circuit High

Blocking in the exhaust?

Oct 07, 2017 | 1996 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides