Question about 2007 Dodge Caliber SXT Sport Hatchback

Open Question

My dodge caliber wont start or turn over p0700 and p161b codes

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Dustybobcat
  • 39 Answers

SOURCE: I have a 2007 Dodge Caliber 2.0 automatic. My wont

the stering wheel has a loke that can interfer with the barrell. so make shore that the steering wheel is not jamed in lock posistion by terning it to a senter position

Posted on Mar 14, 2010

Ad
  • 20 Answers

SOURCE: My 2007 dodge caliber wont start my radio and

there should be a single red light on the dash around the speedometer, if it dosent turn off after 5 seconds after you turn the car on it means the car dosent recgnoize the computer chip thats in your key... check that first, if the light stays on then your key is bad

Posted on Jul 14, 2010

cansmo
  • 2431 Answers

SOURCE: my 2007 dodge caliber wont start

You are dealing with 2 possible problem. The ignition switch,or the alarm, If you have a alarm problem the vehicle will crank then in 2 seconds shut down,this is because the key is recognized,now if this is the problem roll down a window and disconnect the negative battery terminal,put the key in the ignition but in the off position.After 5 minutes reconnect the battery and turn the ignition on but dont crank the engine leave for 1 minute. Then see if that resolved the issue.Now if its an ignition switch problem crank the engine and slowly let it go.try to keep the key in the position where it stays running. By the way there is a campaign of a recall dealing with a TIPM software update Re-configure ,anti-theft system. Customer satisfaction notice G42. You will have to see the dealer for this campaign.

Posted on Nov 03, 2011

  • 1207 Answers

SOURCE: 2006 dodge 1500 hemi-trouble codes p0700 and p0800, what are they?

the P0700 means Transmission Control System (MIL Request)
the P0800 means Transfer Case Control Circuit

hid conversion kits

Posted on Aug 27, 2012

jsleigh3
  • 78 Answers

SOURCE: I have a 2007 dodge caliber. Recently the battery died. After replacing it I all of a sudden had codes p161b and p0700 P161- control module torque performance condition P0700- transaxle control system

Battery changes can mess with a computer's settings. (I've had it happen to mine!) Restart car and wait 1-15 min. and see if codes persist.

Posted on Feb 19, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Compass. What are the probable causes of DTCs P161B and P0700?


which engine? first year is 2007
which one? errors very by , ENGINE!
2.0 L World I4 (gasoline)
2.0 L VW I4 (turbo diesel)
2.2 L OM651 I4 (turbo diesel)
2.4 L World I4 (gasoline)


p07 means transmission errors,. and need a real scan tool to read them ALL full codes, 700 means (have errors in trans scan me the correct and full way)
P161b (p1 means jeep factory codes, power train)

not B161 or P1618
are you sure, it matters.
this means the battery was low
the battery was disonnected
or while cranking at -40F starter overloaded a weak or discharged battery.... (heard the starter run slow, did you?)
it means battery voltage discover too low for any reasons.,.
P161B-BATTERY DISCONNECT / TCM INTERNAL

16be68b4-e970-47f6-b47f-99709fbee501.jpg

Feb 16, 2016 | Jeep Cars & Trucks

1 Answer

I have a problemis with my dodge caliber 2009 the transmissoin dos not changing,there is the code po700 po1729


You have a transmission problem p0700 transmission control system malfunction. P1729 4x4 low switch error

Jul 20, 2015 | 2009 Dodge Caliber

1 Answer

Car turns off after it is started, scanned and gave codes P0700 and P161B


Why does my car turn off while in motion? I've also noticed that it does it when gas is low.

Jan 03, 2014 | 2008 Dodge Caliber

2 Answers

What should i do to fix error code p0700 on a 2010 dodge caliber


p0700 is a transmission overall problem -tcm transmission control module problem u need to have the truck hook up to a diagnostic reader for the transmission -first check the fluid make sure full and not burnt[may need to change fluid and filter other than that their are to many problems that can cause the code

Mar 31, 2013 | Cars & Trucks

2 Answers

I have a 2011 dodge caliber and it isz throw a c0700 code could u tell me what this is


P0700 DODGE - Transaxle Control System Malfunction

Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transaxle shifting problems

Possible causes - Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module

Tech notes Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem.

P0700 DODGE Description The transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transaxle controls.
CLEAR THE CODES AND SEE IF IT RESETS. MOST LIKELY NOT A PROBLEM

Sep 07, 2011 | 2002 Dodge Grand Caravan

1 Answer

I have a 2007 Dodge Caliber 2.0 automatic. My wont


the stering wheel has a loke that can interfer with the barrell. so make shore that the steering wheel is not jamed in lock posistion by terning it to a senter position

Mar 14, 2010 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

My car will not start starter will not turn over. i took my car to a mechanic and he ran the fault codes for me and came up with P161B P0700 P0113 electrical shifting isnt working at the moment


Possible causes:

WRONG VEHICLE CALIBRATION FUSED B(+), TRANSMISSION CONTROL OUTPUT, AND/OR GROUND OPEN TRANSMISSION CONTROL MODULE (TCM)

Jul 04, 2009 | 2008 Jeep Compass

Not finding what you are looking for?
2007 Dodge Caliber SXT Sport Hatchback Logo

Related Topics:

1,619 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...