Question about 1995 Saturn Sl

1 Answer

Changed timing chain and need to align to cam with the crang

How do you align the timing marks up on a 1995 saturn L series 1.9.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 186 Answers

Align the chain with the colored links on the chain over the marks on the cams.Twin cams Have a small hole on the cam gears that will align with a hole in the front of head.Crank Gear has a pip mark that goes straight up.colored links on crank go to the 5 & 7 Oclock position on the lower crank gear with pip mark on crank gear at 12:00.Hope this helps

Posted on May 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instruction changing timing belt 1979 Alfa Romeo Spider Veloz?


With Cam Caps loosened, FIRST loosen timing chain tensioner, press it in to loosen tension, Crank using ratchet to TDC (Top Dead Center on crank pully, (to keep from damage to pistons), align Exhaust Cam Timing Mark to mark on #1 Exhaust cam cover, then take up slack between Exhaust & Intake Cams (on top between the cams), Then align the Intake Cam to mark on #1 Cam Cap, "Now" loosen the 17mm bolt to tighten timing chain, rotate engine using rachet two times, reset TDC at the crank, and look at "Cam Timing Marks on both the Exhaust, and Intake Cams. If you did all this correctly the "Timing Marks" should be lined up so TDC,Exhaust, and Intake marks are all the same.

Oct 10, 2014 | 1979 Alfa Romeo

1 Answer

Timming chain broke


place no 1 piston at TDC compression stroke. There are procedures for the timing of the balance shafts but if it is only the timing chain I will go to that
Align uniquely coloured chain link with intake camshaft sprocket timing mark-- INT--. ( this will be pointing at the 2 o'clock position)
install timing chain and sprocket as an assembly
align first matching coloured chain link crankshaft timing mark (5 o'clock position)
align the second matching coloured chain link with exhaust cam shaft timing mark--EXH ( at the 11 o'clock position
There is a special procedure to reset the balance tensioner and it is different to the timing chain procedure.

To reset cam shaft timing chain tensioner push piston fully and turn clockwise until locked
Once the tensioner has been compressed ensure the distance from end to end is 2.83 inches . If not repeat the resetting process
vehicles 30.000 miles the tensioner is released when the engine is first started . In vehicles over 30.000 miles manually release tensioner by tapping the plunger
Note cam shaft and crank shaft sprockets bolts MUST only be used once. If you want details on the balancer chain procedure then make a comment in the box
use tension wrench and a degree gauge
cam bolts are tensioned to 63 ft lbs + 30 degrees
crank shaft pulley is tensioned to 74 ft lbs + 75 degrees

Feb 02, 2014 | 2003 Saturn ION

1 Answer

Chain mark timing gabriel align


Here's a link to your timing chain.

Jun 07, 2013 | 1995 Nissan Maxima

1 Answer

We are installing a timing chain in our 1995 Jeep cherokee sundown edition for the first time can you please send me the timing gear specs the motor is a 4.0 with air. thank you


By :"specs" I assume you need install position? To index the gears, whne you take it apart, turn the crank pulley 'till the timing mark aligns with the "0" on the timing scale. Don't turn the crankshaft again. When you are ready to install the chain, locate the mark on the crank gear and align the mark on the cam gear so they point to each other. The mark on the crank gear should be at 12 o'clock and the cam gear mark at 6 o'clock. Make sure when you put the cam gear on the cam that the location pin fits into the gear to position it correctly. Jeep recommends that after putting the chain and gears on, you rotate the engine by hand and place the crank mark at 6 o'clock and the cam gear at 3 o'clock, then count the number of pins in the chain (pins, not links) between those two points. There should be 15 pins. If you are rebuilding the engine and have the cylinder removed, it's a good time to check the front crank pulley (some have the outer ring move on the rubber). Put a piece of flat steel across #1 cylinder with a bolt through the steel extending into the bore center. Turn the engine by hand 'till the piston contacts the bolt. Make a mark on the pulley and turn the engine in the opposite direction till contact is again made. Your timing mark on the pulley should be exactly between the two marks you made. If not, make a new mark at that point and use that as your actual TDC reference. If it is radically off, replace the pulley.
When setting up cam position I always use a degree wheel. If you are installing an aftermarket cam
its important to do that. If you're just replacing a stock chain, You will be fine with the method I've outlined.

May 16, 2011 | 1995 Jeep Grand Cherokee

1 Answer

Do you have a diagram for 2003 saturn timing belt


The 2.2 liter engine uses colored links on the timing chain to align with the marks on the gears. You just have to rotate the engine to where the copper chain link is up on the upper right side of the intake can gear--aligned to the INT diamond on the gear. Then the silver link should be down at about 5 O-Clock on the crankshaft timing mark. The other silver link should then be aligned to the mark on the exhaust cam sprocket. See picture below.

For the 3.0 liter engine, there are marks on the belt that line up with marks on the gears. The book calls out special tools to hold the cam sprockets in alignment while the belt is put on. There is also a special tool to lock the belt onto the crankshaft sprocket. See pictures below.
Please let me know if you have questions.

2.2 liter:

jturcotte_425.gif



jturcotte_426.gif

3.0 liter:
camshaft sprocket alignment with belt marks

jturcotte_427.gif


Camshaft locking tools

jturcotte_428.gif



Crankshaft belt tool

jturcotte_429.gif


Properly adjusted tensioner

jturcotte_430.gif

Dec 08, 2010 | 2003 Saturn VUE

1 Answer

Need directions on how to install a timing chain on a 2002 Saturn L series 2.2 liter along with the allignment marks for the intake and exhaust cams


To Install:
  1. Install or connect the following:
    • Timing chain drive sprocket to crankshaft
      1. Rotate the crank so the mark on the sprocket is at the 5 o'clock position
  2. Assemble chain to the intake camshaft sprocket alignment copper link to the "INT" diamond timing mark on the camshaft sprocket sat_car_22_tmng-chn_pos.gif

    NOTE: When lowering the timing chain rotate the assembly 90° to allow the chain to fall between the cylinder block bosses then rotate the assembly back so the camshaft sprocket is facing forward.
    sat_car_22_tmng-c_hsng_opng.gif

  3. Lower the assembly through the chain housing opening on top of the cylinder head. Use care to ensure that the chain goes around both sides of the cylinder block bosses NOTE: The crankshaft sprocket timing mark will be at approximately the 5 o'clock position.
  4. Route chain around crankshaft sprocket and align silver link to the timing mark sat_car_22_set_tdc.gif

    NOTE: The camshaft sprocket bolts are not reusable; they are torque-to-yield and must be discarded to prevent premature failure.
  5. Install or connect the following:
    • Intake camshaft sprocket loosely onto the intake camshaft then install the new camshaft sprocket bolt finger tight NOTE: It is not necessary to align the sprocket-to-camshaft offset notch at this time.
    • Adjustable timing chain guide through the opening on top of the cylinder head then install the chain guide bolt; torque to 89 lb-in. (10 Nm) sat_car_22_ajst_tmng-ch_guid.gif

      sat_car_22_cm-shft_sprkt_blts.gif

    • Exhaust camshaft sprocket loosely onto the exhaust camshaft with the timing mark on the sprocket aligned with the silver link then install a new camshaft sprocket bolt finger tight
    NOTE: It is not necessary to align the sprocket-to-camshaft offset notch at this time.
    NOTE: The camshaft sprocket bolts are not reusable; they are torque-to-yield and must be discarded to prevent premature failure.
  6. Align the camshaft sprocket-to-camshaft then tighten the camshaft bolt using the following procedure: sat_car_22_crnk_tmng-c_mrk.gif

    NOTE: Do not rotate either camshaft more than 1/2 turn in either direction with the crankshaft at Top Dead Center (TDC). To do so may cause valve to piston contact resulting in a damaged valve and/or a damaged piston.
    • Ensure that the sprocket timing mark is at the 5 o'clock position
    • Rotate the intake camshaft using a 24mm wrench on the flats of the camshaft until the sprocket-to-camshaft alignment notch seats
    • When the sprocket seats on the camshaft tighten the sprocket bolt finger tight
    • Rotate exhaust camshaft using a 24mm wrench on the flats of the camshaft until the sprocket-to-camshaft alignment notch seats
    • When the sprocket seats on the camshaft tighten the sprocket bolt finger tight
  7. Verify that all colored links are aligned with the appropriate marks on the camshaft and crankshaft sprockets NOTE: If they are not repeat steps 1C through 4.
  8. Install the fixed timing chain guide and bolts; torque to 89 lb-in. (10 Nm)
  9. Install the fixed timing chain guide bolt access hole plug; torque to 30 lb-ft. (40 Nm)
  10. Install upper timing chain guide and bolts; torque to 89 lb-in. (10 Nm) NOTE: Use a 24mm wrench to support the camshaft while applying torque to the camshaft sprocket bolt. Do not torque the camshaft bolts against the timing chain as it may damage the timing chain.
  11. Torque the intake and exhaust camshaft sprocket bolts; torque as follows:
    • First Pass: 63 lb-ft. (85 Nm)
    • Second Pass: Turn an additional 30° using a torque angle gauge
  12. Install the sealing ring and tensioner assembly; torque to 55 lb-ft. (75 Nm)
  13. Install or connect the following:
    • Timing chain oil nozzle and bolt; torque to 89 lb-in. (10 Nm)
    • Camshaft cover assembly
    • Engine front cover
    • Negative battery cable; torque to 13 lb-ft. (17 Nm)

Nov 12, 2010 | 2002 Saturn L-Series

1 Answer

I am replacing the timing chain on my 02 saturn. I replaced the head gasket and the chain slipped. Now i have to re-align the marks to put the cahin back on how should I do this? How are the marks on the...


okay i posted you a picture of the postion. be carefull not to turn the crank or the cams or you will damaged the valves. let me know if you need more hlep.

Jun 13, 2010 | 2000 Saturn SL

1 Answer

How to setup the timing chain for BMW


The sadder thing is you have a 740. align both cam pulley per the book or where you marked them before you took the chain off. They're marked in relation to top dead center of the #1 cylinder and crankshaft.

Didn't do that beforehand.......uh oh. Tow it to dealer, bring one wheelbarrow full of fresh cash. Drive away in about 6 hours.

Jun 01, 2010 | 1992 BMW 3 Series

1 Answer

Cam align marks chain


My apologies for the delayed response. I am going back to answer unanswered questions.
CLICK
on the following LINK. It has the Cam Alignment Mark Diagrams you will need.
If you would: Before Clicking let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks!

Not sure what L-series you have.

For the LS2:
http://www.2carpros.com/car_repair_information/year/2000/make/saturn/model/ls2/2000_saturn_ls2_timing_belt_diagram_marks.htm

For the LW2:
http://www.2carpros.com/car_repair_information/year/2000/make/saturn/model/lw2/2000_saturn_lw2_timing_belt_diagram_marks.htm

Dec 21, 2009 | 2000 Saturn L-Series

2 Answers

Need to know how to set the timing


Cylinder #1 set at TDC, compression stroke. Cam marks level with head, aligned with mark on cover, or if unclear where to mark the cam: SET Cam at point where intake valve has just closed and both valves are shut on cyl. #1, cam gear marks should start to appear more clearly to technician, along with corresponding alignment points. This is ballpark. Remember, on clockwise rotation, after cylinder #1 intake valve(s) are shut, the cam will continue to rotate 90 degrees and come to rest at a position in which both exhaust and intake valves are at their maximum lash point. (the most play) Hopefully if you get this close, you will decipher the marks that exist on your Bavarian machine.

Jan 19, 2009 | 1999 BMW 318 ti

Not finding what you are looking for?
Cars & Trucks Logo

749 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...