Question about 2010 Nissan Navara DoubleCab

Open Question

Hard to push clutch down

Hard to push down clutch and takes a while to kick in

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My clutch is hard to push down and I have fluid coming out of back driver side wheel of my 1990 geo tracker


the cable is seized, they all do this at near 150k miles.
replace it ,its cheap and easy and avoids 3 other expensive repairs.
the wheel slave cylinder is bad, or line rusted through. replace them.
replace that, which leaks...

if the cable is bad, the fire wall cracks.
or the pedal lever spline strips
not how there are many cables. for different bodies
http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

May 24, 2015 | 1990 Geo Tracker

1 Answer

Replaced clutch and now won't shift into 1st, 3rd, or 5th gear


if it worked before why a new clutch,,,(context wins, here/??????)
ok, so you the clutch is failing,
you never posted the symtoms, not really
does car start in gear with clutch depresses, or start to move
does car take off in 1st ?
or is it just moving fast issues>????
cant up shift, cant down shift
hard to shift. (blocks)
grinds.

my wild guess, based on no input is the clutch linkage,
was never adjustED
the side kicks (not sport 1.8L) all have
cable clutches, and the 1 inch rule stated here.
i bet you didnt adjust it or the linkage splines are damaged.
or the pedal is cracked , caused by bad cable.
always replace the cable first. is it breaks other things if not.

http://www.fixkick.com/tranny/clutch/clutch-on-kick.html


tell the full story and get ,very accurate tests to do,
and inspections.

Sep 02, 2014 | 1995 Suzuki Sidekick

1 Answer

Pedal hard to push in has new cluch


the cables is #1 top failure. and can damage car, or it can stick and cause a wreck
http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

never run old cables here.
they fail inside, big time, where you will never see,
also if you keep it like this, the spins on the top of the clutch pedal
strip, (good luck finding that)
or fire wall cracks at the mount for cable.
or the pedal welds snap.
seen 100's on all tracker/kick forums.

Apr 02, 2014 | 1992 Geo Tracker

1 Answer

I had a new clutch asembly and new slave cly put in my 1990 nissan truck about year and half ago. My problem is my clutch is hard to push down and if i don't push it all the way to floor it will g


replace the clutch master cylinder. The rubbers on the piston swell over time and/ or break down blocking up the ports in the cylinder.. Wrong fluid is the main culprit for this type of fault.

Mar 29, 2013 | Cars & Trucks

1 Answer

Where is the adjustment for the clutch on a renault scenic 2004


I have a renault megane scenic 1.4 16v 04 plate my clutch is extremely high I only have to push down a 1mm or 2mm for bitting point is there anyway I can adjust it I did take it back to the garage I bought it from and they just dismissed the issue saying it's fine the pedle is easy to push still the car has sone 77thousand miles thank you for any help

Mar 22, 2012 | 2005 Renault Scenic 1.5

1 Answer

I just bought a 1997 BMW Z3 1.9 engine 5 speed, It is very hard to shift into all gears, if I push it all the way to the floor hard it gets easier but still sort of hard, is there a adjustment for the...


you have a bought a car with a worn out clutch end of story ,so take gearbox out and then take old clutch in hand to auto factor so you get the right clutch first time then fit it and you will have a nice car ,the clutch is hard to push down because the diaphramn spring in the pressure plate is working overtime because the clutch disk is worn to excess .not too difficult on this rear wheel drive car though just dirty work

Feb 26, 2011 | BMW Z3 Cars & Trucks

1 Answer

1999 honda prelude manual transmission isn't disengaging all the way when i shift, sometimes locking the shifter in gear or not allowing me to up or down shift. I know my master and slave cylinders need to...


This depends as dose it do it when cold or hot.
2nd when you push in pedal and put in gear dose it go in clean or hard to select 3rd can you hear a grinding noise when pushing in pedal and noise goes
when you take you foot off the clutch pedal IF so then its the thrust bearing on clutch REPLACE ALL .4th if you push in clutch pedal and select a gear and let the clutch out if drive right out (replace)

Sep 27, 2009 | 1999 Honda Prelude

1 Answer

My pontiac vibe Ac has stopped working..it started taking a long time to kick in ...now it only kicks on for a short time if im lucky.


the clutch on the ac compressor is going out.

replace the ac compressor (when you push the a/c button it should imidiately kick the compressor on).

also check the connection on the compressor, along with the fuses.

Aug 14, 2009 | 1995 Jeep Grand Cherokee

2 Answers

Clutch pedal is very heavy to push down


If the clutch in your car is hydralic there is no way to adjust that type of clutch. That you describe the clutch as being hard to push and that you have to have the clutch "right down on the floor to engage a gear" is an indication that the clutch is worn and needs to be replaced. If the clutch in your car is pushed by a cable, the cable might be adjustable and if that is the case you might get a few more months of use from the car, but the fix is still the same, you will need to get a new clutch put in your car.

Nov 26, 2008 | 2005 Hyundai Tucson

Not finding what you are looking for?
2010 Nissan Navara DoubleCab Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...