Question about Hyundai Motor 2003 XG350

1 Answer

Programming factory remote on 2003 Hyundai XG350

I found instructions to program the remote as follows:

1. Access alarm system control module located behind driver’s side fascia panel
2. Ensure memory switch is in off position.
3. Turn ignition to on
4. Wait 5 seconds, set memory switch to set position.
5. Push remote lcok button to send code to alarm system control module

Where is the driver's side fascia panel and how do I remove it?

Thanks

Guy

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Again, the remotes can only be programmed by a Hyundai Technician (ETACS - Electronis Time and Alarm Control System).

Posted on May 27, 2009

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ghost4548
  • 776 Answers

SOURCE: Program factory remote keyless entry 2003 Hyundai XG350

I've informed you of what you need to do. Take the veh into a Hyundai Service Center - let them program the remotes.

Posted on May 31, 2009

ghost4548
  • 776 Answers

SOURCE: Program factory remote keyless entry: 2003 Hyundai XG350

The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

Posted on May 27, 2009

ghost4548
  • 776 Answers

SOURCE: program factory remote keyless entry for 2003 Hyundai XG350

This bulletin supersedes TSB# 02-90-001.
DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:

  • 2001 - 2004 MY Elantra
  • 2001 - 2004 MY Santa Fe
  • 2002 - 2004 MY Sonata
  • 2001 - 2004 MY XG300/350 0390020a.gif
NOTE
  • The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
  • The most current Keyless Adapter Cable Instructions are available in the following shop manuals:
SHOP MANUAL

PAGES

2004 MY Elantra
BE-73 - BE-74
2004 MY Santa Fe
BE-43 - BE-44
2004 MY Sonata
BE-40 - BE-41
2004 MY XG350
BE-46 - BE-47
KEYLESS ADAPTER CABLE INSTRUCTIONS:
  1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable. 0390020b.gif
  2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
    0390020c.gif
  3. Turn the Hi-Scan Pro ON
    and press ENTER
    . NOTE "Release date 29. Sep. 2003" OR LATER
    must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
    0390020d.gif
  4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
    and press ENTER
    . 0390020e.gif
  5. Select vehicle model and press ENTER
    . 0390020f.gif
  6. Select option "TRANSMITTER CODE SAVING"
    and press ENTER
    . 0390020g.gif
  7. Ensure that the key has been removed from the ignition cylinder before proceeding. 0390020h.gif
  8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
    0390020i.gif
  9. Press ESC
    on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
  10. Turn the Hi-Scan Pro OFF
    and disconnect the adapter cable from the multi-purpose connector.

Posted on May 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reprogram a keyless remote? Where is the alarm system control module located?


go to google! or the parts dept where you got the remote they have instructions for it there

May 05, 2016 | 2002 Hyundai XG350

1 Answer

HOW PROGRAM THE KEY LESS ENTRY FOR SONATA 2012


  1. Cars
  2. Car Maintenance
  3. General Car Maintenance
  4. How to Program Keyless Entry Remotes in a Hyundai Sonata
How to Program Keyless Entry Remotes in a Hyundai Sonata By Christian Killian, eHow Contributor
20Found This Helpful The keyless entry system in your Hyundai Sonata is part of the factory alarm system. If you have to replace a lost or damaged remote, reprogramming will be necessary. The remote is important because not only does it lock and unlock the doors, it also arms and disarms that factory alarm when you open or close your car doors. New remotes are available from any Hyundai dealer. While they will program it for you, you can do it yourself and save a programming fee.
How to Program Keyless Entry Remotes in a Hyundai Sonata(Kleophaus Livingston/Demand Media)

Other People Are Reading


Step 1: Locate the fuse panel under the dash on the driver's side of the car. Just below it is the control module for the factory alarm system. Open the cover on the alarm system control module and locate the memory switch inside.
(Kleophaus Livingston/Demand Media) Step 2: Verify that the switch is in the "Off" position; if it is not, switch it to the "Off" position. This is important for the system to understand what you want it to do when you move to the programming mode.
(Kleophaus Livingston/Demand Media) Sponsored Links
Step 3: Insert the key into the ignition of your Sonata and turn the key to the "On" position. Wait for 60 seconds, then move the memory switch inside the control module to "Set."
(Kleophaus Livingston/Demand Media) Step 4: Depress and hold the "Lock" button on your remote for one full minute. This allows the remote and the control module to communicate and sync. Release the "Lock" button and turn the memory switch in the control module back to the "Off" position.
(Kleophaus Livingston/Demand Media) Step 5: Turn the ignition switch to the "Off" position and test the remote by pressing the "Lock" or "Unlock" button, verifying that the doors do lock or unlock.


Read more : http://www.ehow.com/how_6362326_program-entry-remotes-hyundai-sonata.html

Mar 29, 2015 | Hyundai Sonata Cars & Trucks

1 Answer

I need instructions to program keyless entry remote for 2002 Hundai Santa Fe


For a 1994 to 2006 Sonata, a 2001 to 2006 Elantra, a 2000 to 2006 XG350 or a 2001 to 2006 Santa Fe, you will need to access alarm system control module. On most of those vehicles it is located on the driver's side fascia panel. But on the Sonata, the facia panel is in the center.

  • 2 Once you have found this module, you will want to ensure that the memory switch is in the OFF position. Then turn the ignition on.
  • 3 Wait 5 seconds and set the memory switch to SET position and then press the remote transmitter lock button to send the code to the alarm system control module.
  • 4 If you would like to program a second remote transmitter then you will need to press second remote transmitter lock button.
  • 5 Next set the memory switch to off, then turn the ignition off. You can confirm your programming by locking and unlocking the vehicle with both of the remotes. good luck my friend
  • Feb 08, 2012 | Hyundai Cars & Trucks

    2 Answers

    2004 Elantra. New door locking bought from the US has instructions and diagrams which don't relate to my car. They show a control unit with a switch and have relevant instructions for programming the...


    Welcome to Fixya

    Try this procedure:

    Access alarm system control module. It is located on the at the facia panel in the center. Once you have found this module, ensure that the memory switch is in the OFF position. Then turn the ignition on. Wait 5 seconds and set the memory switch to SET position and then press the remote transmitter lock button to send the code to the alarm system control module. If you would like to program a second remote transmitter then you will need to press second remote transmitter lock button. Next set the memory switch to off, then turn the ignition off. You can confirm your programming by locking and unlocking the vehicle with both of the remotes.

    Thank you for using Fixya!

    Aug 21, 2011 | Hyundai Elantra Cars & Trucks

    2 Answers

    Hyundai santa fe key fob 1 works 1 does not have changed battery deal says to buy new ,can i unlock with key without alarm going off


    System operation
    Pressing remote control lock button locks vehicle and activates system Fig. 1 . Indicators flash once. Pressing remote control unlock button unlocks vehicle and deactivates system Fig. 1 . Indicators flash twice.
    Fig. 1
    Synchronization
    When
    System malfunction. Remote control added or replaced.
    How
    Access alarm system control module located under driver's side lower fascia Fig. 2 . Set memory switch to SET position. Press remote control lock or unlock button. Set memory switch to OFF position. Confirm synchronization has been successful by locking and unlocking vehicle. Repeat procedure for second remote control. Synchronization can also be carried out using diagnostic equipment.
    NOTE: A maximum of 2 remote controls can be programmed. NOTE: If remote control fails, system can be deactivated as detailed in the owner's handbook.

    Jul 30, 2010 | 2003 Hyundai Santa Fe

    1 Answer

    Hyundai sonata 2002 remote


    There is a special (proprietary) programming electronics 'black box' for the keyless entry system on all Hyundai vehicles for programming the remotes. This programming is stored in either the BCM (body control module) or the ETACS module (Electronic Time and Control System).

    May 22, 2009 | Hyundai Motor 2002 Sonata

    2 Answers

    Program factory remote keyless entry: 2003 Hyundai XG350


    The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

    May 22, 2009 | Hyundai Motor 2003 XG350

    1 Answer

    Program factory remote keyless entry 2003 Hyundai XG350


    I've informed you of what you need to do. Take the veh into a Hyundai Service Center - let them program the remotes.

    May 22, 2009 | Hyundai Motor 2003 XG350

    1 Answer

    Program factory remote keyless entry for 2003 Hyundai XG350


    This bulletin supersedes TSB# 02-90-001.
    DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
    or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:
    • 2001 - 2004 MY Elantra
    • 2001 - 2004 MY Santa Fe
    • 2002 - 2004 MY Sonata
    • 2001 - 2004 MY XG300/350 0390020a.gif
    NOTE
    • The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
    • The most current Keyless Adapter Cable Instructions are available in the following shop manuals:
    SHOP MANUAL

    PAGES

    2004 MY Elantra
    BE-73 - BE-74
    2004 MY Santa Fe
    BE-43 - BE-44
    2004 MY Sonata
    BE-40 - BE-41
    2004 MY XG350
    BE-46 - BE-47
    KEYLESS ADAPTER CABLE INSTRUCTIONS:
    1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable. 0390020b.gif
    2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
      0390020c.gif
    3. Turn the Hi-Scan Pro ON
      and press ENTER
      . NOTE "Release date 29. Sep. 2003" OR LATER
      must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
      0390020d.gif
    4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
      and press ENTER
      . 0390020e.gif
    5. Select vehicle model and press ENTER
      . 0390020f.gif
    6. Select option "TRANSMITTER CODE SAVING"
      and press ENTER
      . 0390020g.gif
    7. Ensure that the key has been removed from the ignition cylinder before proceeding. 0390020h.gif
    8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
      0390020i.gif
    9. Press ESC
      on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
    10. Turn the Hi-Scan Pro OFF
      and disconnect the adapter cable from the multi-purpose connector.

    May 22, 2009 | Hyundai Motor 2003 XG350

    Not finding what you are looking for?
    Hyundai Motor 2003 XG350 Logo

    733 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    76051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8266 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...