Question about 1993 Ford Festiva

Open Question

Timing cover - 1993 Ford Festiva

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change timing belt


timing belt? on a Jeep? 05 wrangler
what engine is this>?
ah the 2.4L
front cover
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the crankshaft vibration damper.
  3. Remove the generator drive belt tensioner assembly.
  4. Remove the timing belt front cover bolts, and remove the covers.


rear cover
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the front covers.
  3. Remove the timing belt.
  4. Hold the camshaft sprocket with Special Tool 6847, or equivalent, while removing the center bolt.
  5. Remove the timing belt idler pulley.
  6. Remove the rear cover fasteners and remove the cover from engine.

Apr 04, 2014 | 2005 Jeep Wrangler

1 Answer

How to mark camshaft on a 1zm-fe engine


Instructions
  1. Check Your Timing Belt
    • Check your owner's manual for the recommended mileage for replacing your timing belt. Replacement for a Toyota Camry is 60,000 miles for 1984 to 1997 models and 90,000 for 1998 to 2004 models.
    • 2Locate the timing belt and examine it for breaks, damage, fraying, worn spots or looseness.
    • 3
    • Inspect the belt for cracked or missing teeth. It's possible that foreign material collected between them.
    • 4Determine if there's damage on both sides of the timing belt. Single-side damage may be caused by the timing belt's guide.
    Remove Your Timing Belt
    • 5Unscrew the bolts to release the lower timing belt cover.
    • 6Disconnect the engine wire protector from the rear belt cover.
    • 7Remove the clamp holding the rear cover's engine wire protector clamp.
    • 8Take the bolts off the front cover and lift it from the engine.
    • 9Line up the crankshaft timing pulley groove with the oil pump by rotating the engine to the right.
    • 10Be sure the camshaft timing pulleys and rear belt covers line up. You may need to rotate the engine one full turn.
    • 11Undo the crankshaft pulley bolt and release the tensioner and dust boot.
    • 12Unscrew the bolts to release the lower timing belt cover.
    Install Your Timing Belt
    • 13Wipe off any oil or water on the pulleys.
    • 14Align the timing belt's front mark with that of the crankshaft timing pulley's mark and the timing belt's installation marks with those on the camshaft pulley.
    • 15Install the pulleys in this order: crankshaft, water pump, left camshaft, No. 2 idler, right camshaft and No. 1 idler.
    • 16Compress the tensioner until the pushrod's holes and housing align. Connect the dust boot to the tensioner then tauten the tensioner's bolts to 20 foot pounds (27 Nm).
    • 17Rotate the crankshaft to the right and line up its timing pulley groove with the oil pump. The camshaft timing marks and those on the rear timing belt cover should match up.
    • 18Put in the timing belt guide and secure the bolts to 21 foot pounds (28 Nm).
    • 19Secure the upper timing belt cover to 74 inch pounds (8 Nm).
    • 20Reinstall the engine wire protector and clamp to the timing belt cover. Replace the lower timing belt cover and secure the bolts to 74 inch pounds (8 Nm).
    • 21Reconnect any remaining items. Start the engine and check that the timing belt is functioning properly.

Nov 05, 2012 | 1998 Toyota Camry

2 Answers

Noise in the timing chain


May be its problem with timing chain and it has to be inspected and replaced.Or its possible that timing chain is got misaligned.

There are few help,links provided related to timing chain assembly and dis-assembly. Go through it and confirm proper inspecting of timing chain.

Click the required help link below:----How to Replace Timing Chain Cover & Seal on Audi A4 ? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-timing-chain-cover-seal.html
----------1982 Toyota Pickup: Set ignition timing, engine overheating, timing chain issue, dist off? http://whatisbyme.blogspot.in/2012/05/1982-toyota-pickup-set-ignition.html
----------How to Remove Timing Chain Cover and Seal on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-timing-chain-cover-and.html

--------


How to Remove Timing Chain and Gears on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-timing-chain-and-gears-on.html

-------


Ford Mondeo ST220 camshaft Timing specifications? http://technoanswers.blogspot.in/2012/02/ford-mondeo-st220-camshaft-timing.html
------------Replacing Timing Chain Cover For 2009 Ford?

http://repairhelpcenter.blogspot.in/2012/03/replacing-timing-chain-cover-ford-2009.html


-----------
Timing Chains & Front Cover Removal on 2008 Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/timing-chains-front-cover-removal-on.html
----------How to Replace Timing Chain Cover, Chain, Sprockets, & Seal On Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-cover-chain.html
---------How to Replace Timing Chain & Sprockets on Ford Windstar? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets.html
---------Timing Chain & Sprockets Replacing on Ford, Mercury and Lincoln? http://fordrepairhelp.blogspot.in/2012/03/timing-chain-sprockets-replacing-on.html
----------How to Replace Timing Chain & Sprockets on Ford Edge and Lincoln MKX? http://howtobyme.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets.html
------How To Replace Timing Chain, Sprockets & Front Cover on Ford Expedition and Lincoln Navigator? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets_356.html
---------Timing Chain, Sprockets, Front Cover & Seal removal for Ford Mustang? http://schematicsdiagram.blogspot.in/2012/03/timing-chain-sprockets-front-cover-seal.html
---------How to Replace Timing Chain on Buick LaCrosse? http://howtobyme.blogspot.in/2012/03/how-to-replace-timing-chain-on-buick.html
---------These details will help.For more help keep updated.Thanks.

Oct 15, 2012 | Cars & Trucks

2 Answers

Need timing gear marks for 2004 Kia Sadona 3.5L engine



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes.

    Kia_Sedona_2002-2006
    Timing Chain, Sprockets, Front Cover & Seal

    Print


    Removal & Installation

    3.8L Engine

    1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
    2. Record the radio anti theft code data.
    3. Remove the engine from the vehicle.
    4. Remove the drive belt. Remove the power steering pump. Remove the air conditioning compressor.
    5. Remove the alternator. Remove the drive belt idler. Remove the drive belt tensioner. Remove the water pump pulley. Remove the intake manifold.
    6. Remove the connector bracket from the left cylinder head cover. Disconnect the right ignition coil connector, condenser connector and remove the bracket.
    7. Remove the left cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    8. Remove the right cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    9. Set the No. 1 cylinder to TDC on the compression stroke. Turn the crankshaft pulley and align its groove with the timing mark T of the lower timing chain cover.
    10. Check that the mark of the camshaft timing sprockets are in straight line positioning on the cylinder head surface. If not rotate the crankshaft 360 degrees. Do not rotate the engine counterclockwise.
    11. Remove the oil pan. Remove the crankshaft damper pulley. Remove the timing chain cover.
      NOTE Be careful not to damage the contact surfaces of the cylinder block, cylinder head and timing chain cover. Before removing the timing chain, mark the right and left timing chains with an identification mark based on the location of the sprocket because the identification mark on the chain for TDC can be erased.
    12. After compressing the timing chain tensioner, install a set pin. Remove the right cam to cam guide. Remove the right timing chain auto tensioner and timing chain tensioner arm.
    13. Remove the oil pump chain cover. Remove the oil pump chain tensioner assembly. Remove the oil pump chain guide. Remove the right timing chain.
    14. Remove the right timing chain guide. Remove the oil pump chain sprocket and oil pump chain. Remove the crankshaft sprocket, oil pump and camshaft drive gear.
    15. Remove the left cam to cam guide. Remove the left timing chain auto tensioner and timing chain tensioner arm. Remove the left timing chain.
    16. Remove the left timing chain guide. Remove the crankshaft sprocket and left camshaft drive. Remove the tensioner adapter assembly.

      0996b43f8020193b.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing chain and related components-3.8L Engine


    To install:
    1. Check the camshaft and crankshaft sprockets for wear and damage, replace as required.
    2. Inspect the tensioner arm and chain guide for wear and damage, replace as required.
    3. Check that the tensioner pin moves smoothly when the ratchet pawl is released with a thin rod.
    4. The key of the crankshaft should be aligned with the timing mark of the timing chain cover. This indicates that the piston is at TDC on the compression stroke.
    5. Install the tensioner adapter assembly. Install the crankshaft sprocket and left camshaft drive.
    6. Install the left timing chain guide and torque the retaining bolts 14-18 ft. lbs.
    7. Install the left timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, timing chain guide, exhaust camshaft sprocket, intake camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201924.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Left timing chain markings and installation: (D) exhaust camshaft sprocket (C) intake camshaft sprocket-3.8L Engine

    8. Install the left timing chain tensioner arm and torque the retaining bolts 14-16 ft. lbs.
    9. Install the left timing chain tensioner and torque the retaining bolts 7-9 ft. lbs.
    10. Install the left cam to cam guide and torque the retaining bolts 7-9 ft. lbs.
    11. Install the crankshaft sprocket, oil pump and right camshaft drive.
    12. Install the oil pump chain and oil pump sprocket. Torque the retaining bolt to 14-16 ft. lbs.
    13. Install the right timing chain guide. Torque the retaining bolts to 14-18 ft. lbs.
    14. Install the right timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, intake camshaft sprocket, exhaust camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201925.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Right timing chain markings and installation: (C) exhaust camshaft sprocket (B) intake camshaft sprocket-3.8L Engine

    15. Install the right timing chain tensioner arm. Torque the retaining bolts to 14-17 ft. lbs.
    16. Install the right timing chain auto tensioner. Torque the retaining bolts to 7-9 ft. lbs.
    17. Install the right cam to cam guide and torque the retaining bolts to 7-9 ft. lbs.
    18. Install the oil pump chain guide. Torque the retaining bolts to 7-9 ft. lbs.
    19. Install the oil pump tensioner assembly. Torque the retaining bolts to 7-9 ft. lbs.
    20. Pull out the pins on both the left and right hydraulic tensioners. Install the oil pump chain cover.
    21. Rotate the crankshaft two revolutions in the clockwise direction. Confirm the timing mark. Be sure to rotate the crankshaft in the clockwise direction.
    22. Apply sealant on the chain cover and on the cylinder head, cylinder block, and lower oil pan. Be sure these parts are free of engine oil and dirt.
      NOTE Before assembling the timing chain cover, the liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201926.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Sealant application (1 inch bead width)-3.8L Engine

    23. Apply sealant on the chain cover.
      NOTE The liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201927.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover sealant application-3.8L Engine

    24. Install a new gasket to the timing case cover.
      NOTE It is important that the dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover in the correct position.


      0996b43f80201928.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover gasket installation (A) gaskets-3.8L Engine

    25. Install the timing chain cover. Torque the retaining bolts in the proper sequence and to specification. The engine should not be started for at least thirty minutes after timing chain cover assembly.

      0996b43f80201929.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover bolt torque sequence and specification-3.8L Engine

    26. Install the timing case cover oil seal.
    27. Continue the installation in the reverse order of the removal procedure.

May 19, 2012 | 2004 Kia Sedona

1 Answer

How do you remove timing cover on a 2001 dodge durango 5.9


this thing, has a lot things to do. a certified technicians only can do the job. but if you wanna do it alone, here are some instruction(s) after removing the parts to have acces on it.
1. Remove the crankshaft pulley using the appropriate socket.
2. Remove the harmonic balancer using the harmonic balancer puller.
3. Loosen the oil pan bolts.
4. Remove the front two oil pan bolts--one on each side of the crankshaft--these two bolts help hold the timing cover in place.
4. Remove the timing cover bolts using the appropriate socket.
5.Pull the cover off the block.
6.Remove the seal from the timing cover using a seal puller(if it is your problem).
7. Clean the gasket mounting surfaces on the engine and timing cover with the scraper.
8. Smear a thin layer of silicone on the timing cover's gasket mounting surface.
9. Fit the gasket on the timing cover.
10. Install the timing cover and tighten the bolts to it's specified torque.
11. Reinstall the two oil pan bolts and tighten them to it's specified torque.
12. Reinstall the accessories in reverse order of removal.

Feb 19, 2012 | 2001 Dodge Durango

1 Answer

Can i check valve timing without pulling off timing cover? 1987 Dodge caravan 2.6 liter


you can check ignition timing but not valve timing unless cover is removed

Jan 21, 2012 | Cars & Trucks

1 Answer

Water pump bolt broke off


Common problem. You are in for a rough ride my friend. The only way to fix that is to remove the rest of the bolts, the front crankshaft dampener pulley and take the timing chain cover off. Usually the bolt is seized into the timing cover itself and the timing cover ends up getting destroyed in the process. Once the cover is out of the way, the bolt will most likely come out fairly easilly with a pair of Vise-Grips.

Fortunately, a replacement timing chain cover is not real expensive. The trick is to get the [BLANKETY] thing off without causing any damage to the engine block. If you are going that far, I recommend putting a new timing chain set on it while you are in there.

Recommended parts: Timing cover gasket and front seal set, timing chain and gear set, and possibly a new timing cover unless you can get it off without ANY damage.

Keep in mind that if you have to pry it off and the pry tool leaves indentations in the gasket surface, or if you "warp" the cover, the timing cover MUST be replaced unless you want to do the job over to fix oil and engine coolant leaks. (It doesn't take much to make the thing leak)

Aug 16, 2011 | 1991 Ford F150

1 Answer

Easiest way to check timing belt


If you simply want to check the timing belt condition, then remove the plastic cover and visually inspect it. If you have the 5 sfe engine, the timing belt cover is a 2 piece assembly, upper and lower. if you have the 7 afe or 4 afe engine the timing cover is 3 pieces and to inspect the top of the timing belt you must remove the 4 nuts holding the valve cover down and the 2 bolts holding the wire loom. remove the whole valve cover. to inspect timing belt condition.

Aug 06, 2011 | 1990 Toyota Corolla

1 Answer

What is the right way to time a 4cyl Chevy S-10 timing chain


1998-2003 To Remove:
  1. Remove or disconnect the following:
    • Crankshaft pulley and hub
    • Drive belt tensioner gm_truck_s10_tcbolts.gif

    • Timing chain cover bolts gm_truck_s10_tc.gif

    • Timing chain cover and gasket
  2. Install a bolt in the end of the crankshaft CAUTION
    Do not install the crankshaft balancer bolt or a bolt longer than 1 inch or damage to the crankshaft threaded hole will result.
  3. Rotate crankshaft until the number 1 piston is at Top Dead Center of compression stroke.
  4. Make sure that the alignment marks are aligned with the tabs on the timing chain tensioner. gm-03-22-611.gif

  5. Measure distance between hole in bracket and unworn surface of timing chain tensioner shoe. NOTE: If distance between the hole and unworn surface of timing chain tensioner is greater than 0.314 in (8 mm), replace tensioner, timing chain and sprockets.
  6. Remove timing chain tensioner bolts.
  7. Remove the timing chain, timing chain tensioner and camshaft sprocket at the same time.
  8. Remove the crankshaft sprocket using special tool J 22888-20A or equivalent.
  9. Remove crankshaft sprocket alignment key.
gm-03-22-612.gif

NOTE: If any camshaft components are being replaced to correct a noise problem, all camshaft drive components must be replaced.
To Install:
  1. Install the crankshaft sprocket alignment key.
  2. Install the crankshaft sprocket using special tool J 5590 or equivalent. gm-03-22-613.gif

  3. Compress the timing chain tensioner spring and insert a pin into the tensioner hole to retain the tensioner shoe.
  4. Install timing chain and timing chain tensioner (do not tighten tension bolts).
  5. Align the crankshaft and camshaft timing marks with the tab on the timing chain tensioner.
  6. Tighten the timing chain tensioner bolts.
    • Torque to: 18 ft lbs (24 Nm)
  7. Tighten the camshaft sprocket bolt.
    • Torque to: 96 ft lbs (130 Nm)
  8. Remove pin from timing chain tensioner hole.
  9. Remove bolt from end of crankshaft. CAUTION
    Inspect the timing chain cover for warping or damage. Replace if needed.
  10. Clean all timing chain cover mating surfaces.
  11. Install or connect the following:
    • Timing chain cover to the engine block
      1. Ensure that the gasket is installed properly in the groove in the timing chain cover
    • Timing chain cover and make sure it fully seated on the alignment dowel pins
    • Timing chain cover bolts
      1. Torque to: 97 inch lbs (11 Nm)
    • Drive belt tensioner
    • Crankshaft damper hub and the crankshaft pulley

Aug 17, 2010 | 2000 Chevrolet S-10

1 Answer

What is timing cover and if this goes do you need to replace timing chain and water pump


engine with 3.3 liters and 3.8 liters are equiped with timing chain.
the timing chain cover is the cover that cover and protect the chain
it must be seal because there is oil that come from the oil pan to lubricate the chain.
normally the cover does not go bad unless the chain broke or some thing hits it.
the water pump is out side and not involed in the timing chain or it cover

Mar 05, 2010 | 1996 Plymouth Voyager

Not finding what you are looking for?
1993 Ford Festiva Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...