Question about 2001 Daewoo Nubira

Open Question

Where is the turning light flasher unit located?

Daewoo nubira 2001 2 litre ,where in the vehicle is the flasher unit for the turning lights located?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: timing sincronization crank and cram shafe

Hi. Here are thi information that you need.

I hope this solve your problem,

c638dc9.jpg
This figure is for the crankshaft. look the mark at lower of the cover.

0333190.jpg OK. this figure is for the camshaft . look the marks at uppur of the back cover and on the sprockets.

OK> If this information is good for you Just RATE it.

Thank you for use fixya.

Posted on Jul 12, 2008

SOURCE: 2000 daewoo nubira brake light problem.

Thanks to your advice my problem is solved. A big fixya is in order. Thanks again

Posted on Oct 07, 2008

alicantecoli
  • 22156 Answers

SOURCE: 2000 Daewoo Nubira camshaft position sensor

on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Posted on Sep 11, 2009

  • 1986 Answers

SOURCE: How to scan the 2001 daewoo nubira fault codes.

Your port should be located under the dash on the driver's side near your knee area. The port should be pointing straight down from the dash. The scanner will be plug and play and you shouldn't have to jump and pins for the OBD-II port. As for the codes, there are so many thousands of codes that you can't even guess what codes will be generated from your scan

Posted on Sep 30, 2009

emissionwiz
  • 75842 Answers

SOURCE: how to change the timing belt on a 2001 daewoo

follow these instructions exactly, be sure u get it right or u will bend the engine valves this is an interference engine, if u have a broken belt u most likey have bent valves, about 90% of the time the valves do get bent.
here are the instructions.

Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on Apr 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the flasher located on a 2002 daewoo nubira


-Check in its manual.


Good Luck

mai lor

Nov 01, 2014 | 2002 Daewoo Nubira

1 Answer

What are the torque specifications and tightening sequence for cam journal and cylinder head for 2001 daewoo nubira 2.0 :(


  1. The torque settings for the cylinder head bolts on a daewoo ...

    www.answers.com > ... > Categories > Cars & Vehicles > Asian Car i need how much pression (torque) for head daewoo nubira 2001 2.0 ... What is the cylinder head torque specs for a 2001 daewoo nubira 2.0 litre engine and ...

Apr 15, 2011 | 2001 Daewoo Nubira

1 Answer

Could you please advise where the Flasher Units are located in a 1997 Daewoo Leganza.


check engine bay fuse 12 and fuse 11 in car
ones for hazzard lights so do they work?
the other for indicators(turn signals)
left hand drive has fuse & relays left kick pannel area and right hand drive vehicles are similar
unit is not shown in workshop manuals
does indicators flash when locking unlocking vehicle? control is also through keyless entry module

Mar 09, 2011 | Daewoo Leganza Cars & Trucks

1 Answer

I heard that 2001 daewoo nubiras were recalled, who can i contact if i believe i have a defective unit?


ok you can check if you have any of the recall problems here http://www.autorecalls.us/aut-04/recalls/2001/daewoo/nubira/78657.html then contact the nearest daewoo dealer to arange repairs. these should be at no expense to you as they are factory faults. hope that helps. let me know how you go.

Feb 04, 2011 | 2001 Daewoo Nubira

1 Answer

Need to know how many litres of unleaded fuel are in the reserve tank once the fuel light comes on t/y


the light comes on at 5ltr(some cars the light flashes at 5 and is solid at 3.

Sep 23, 2010 | 2000 Daewoo Nubira

1 Answer

My 2001 daewoo nubira will not shift from park


do you have brake lights?? if not brake switch

May 17, 2010 | 2001 Daewoo Nubira

1 Answer

How to scan the 2001 daewoo nubira fault codes.


Your port should be located under the dash on the driver's side near your knee area. The port should be pointing straight down from the dash. The scanner will be plug and play and you shouldn't have to jump and pins for the OBD-II port. As for the codes, there are so many thousands of codes that you can't even guess what codes will be generated from your scan

Sep 30, 2009 | 2001 Daewoo Nubira

1 Answer

Were is the flasher module located on a 1999 daewoo nubria


Most vehicles lefthand drive somewhere above your right foot above .
I usually find them there. Some cars have two of them.

Apr 08, 2009 | 1999 Daewoo Nubira

1 Answer

Oil light is blinking on 2001 daewoo nubira only when at a stop.


Hi. there could be three issues here. One could be that you need to change the oil in the engine. Secondly, the oil pump itself may be malfunctioning. Also, the oil sending unit(module) may be malfunctioning as well. A good starting point would be to check the oil to see if its low or needs changing.


please rate and god bless.

Mar 18, 2009 | 2001 Daewoo Nubira

Not finding what you are looking for?
2001 Daewoo Nubira Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75824 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...